Henderson-Hasselbalch equation || Application and calculations

Рет қаралды 28,464

4 жыл бұрын

Can we find pH of weak acid or weak base by knowing its concentration? Absolutely we can't as pH depends on its pKa and concentration of ionized form. Here Henderson-Hasselbalch equation comes into the play. So in this video, we have discussed significance of this equation along with few practical problems.
#phandpka
#henderson
#weakacids

Пікірлер: 23

@rashmibadsiwal7204 3 жыл бұрын

sir please continue this series its very helpful

@rashmibadsiwal7204 3 жыл бұрын

very detailed explanation sir thanks alot for the video

@ayade74 3 жыл бұрын

Great explanation, thank you

@mohamedabdulkadir8032 3 жыл бұрын

That was a nice explanation

@jaluzworld624 3 жыл бұрын

thank u so much.helpful vdo

@VarshaSharma7 3 жыл бұрын

Awesome ❤️

@pain_is_ultimate 3 жыл бұрын

Thx sir!

@pain_is_ultimate 3 жыл бұрын

Sir,In gpat and Niper examination, do they provide logarithm book for calculating final ans?

@egpat 3 жыл бұрын

As it is a online exam, they will not provide any logarithm book. You have to calculate on the rough paper given to you at that time.

@mh72-show11 3 жыл бұрын

For weak base POH = pkb + log BH+ /B …. I think

@ohchevi4268 3 жыл бұрын

how to solve if we dont knw the mole of base? like for example, how many moles NaoH to add to 0,040 mole of NaH2PO4 (Pka = 2), So we can get pH = 7,0 ??? please help me....

@angusmacchesney5810 3 жыл бұрын

I am not an expert but I can try to help here. The NaOH would react with the acid to form conj. base, which would be needed for the H-H equation. *Reaction: NaH2PO4 + NaOH -> Na2HPO4 + H2O* Using the H-H equation, with the goal in mind, I would get: *7.0 = 2 + log({mol NaOH}/{0.040 mol NaH2PO4})* Since the weak acid and strong base are in the same amount of liquid, you do not need to calculate molarity. Moving the 2 over, we get this equation: *5 = log({mol NaOH}/{0.040 mol NaH2PO4})* Rearranging the equation (by using properties of logarithms): *10^5 = (mol NaOH)/(0.040 mol NaH2PO4)* Dividing both sides by 0.040 we get: *100000*0.040 = mol NaOH* To eventually get the amount of moles of NaOH needed: *4000 mol of NaOH.* That seems ridiculously off but that's what I calculated, so maybe I did something wrong, however it seemed right when I plugged it in. The HA would be the NaH2PO4, and the A- would be Na2HPO4 (seems wrong, again, but this whole thing is wacky). I know this is late but I hope this helps!

@Sujeetsingh-eu9bz 4 жыл бұрын

How to calculate the ph of 0.005N HCL

@egpat 4 жыл бұрын

You can use simply -log(0.005) which gives you a value of 2.3

@Sujeetsingh-eu9bz 4 жыл бұрын

Thank sir

@Sujeetsingh-eu9bz 4 жыл бұрын

How to calculate log and antilog value

@egpat 4 жыл бұрын

Log value can be obtained from logarithm tables or simply by using a calculator. Antilog can be obtained by taking 10 to the power of x in calculator.

@Sujeetsingh-eu9bz 4 жыл бұрын

Thank you sir

@c.v.anjali8670 3 жыл бұрын

Sir can you give some reference book on this topic❤🥳

@egpat 3 жыл бұрын

So many references we can quote, but you can refer Vogel's textbook of quantitative chemical analysis. Thank you.

@c.v.anjali8670 3 жыл бұрын

@@egpat thank you😁👍

@dineshpardhi744 2 ай бұрын

There is major mistake I found while I watched this video. Value of pH in HENDERSON HASSELBALCH EQUATION is pKa +log [salt]/[acid] whereas value for pOH is pKa+log [salt]/base. in both equation salt is in NUMERATOR. But in this video pH value for weak acid mentioned salt in the Numerator whereas for pOH value salt mentioned in the DENOMINATOR.

@egpat 2 ай бұрын

You have mistaken. In the video it is given pH of weak base, not the pOH equation. For a weak base, when you calculate pH, salt comes in denominator. Even for a base, it is convention to measure pH rather than pOH. Hope it is clear. Thanks for watching.