How to adjust the clamp on our paper cutters so that it clamps level. Also how-to replace the blade or remove it for sharpening.
Пікірлер: 33
@onionike4198 Жыл бұрын
Cool, My clamp became skewed shortly after use, but it's so easy to fix I'm not at all bothered by it. Thanks for the tutorial! :D
@PoisonousRakun Жыл бұрын
Awwwwesome! I spent half a ream damaged because i didnt know my clamp is skewed already. This video is simple and actually works! Thank you so much
@joepolach47144 жыл бұрын
Thanks. Made me look like a pro in the office.
@pratibhamootoo64023 жыл бұрын
Thank you thank you I thought I would not be able to fix my clamp thank u sir I appreciate this video you clamp is totally uneaven
@jessicaosburn64064 жыл бұрын
How do you adjust the blade so its level? It's been cutting straight but now nothing is cutting if it's up against the top. It is sitting uneven like the clamp in this video.
@pratibhamootoo64023 жыл бұрын
This cutter is amazing and has helped me alot
@HardlyAMemory Жыл бұрын
I wish you would add a video about leveling the blade. Several people have asked. Apparently it is not the same as leveling the clamp, because I tried that.
@aresnguyen_rsv8 жыл бұрын
Very useful. Thank you for posting this!
@thefaughns9 жыл бұрын
Huge help, thanks!
@mattanderson70652 жыл бұрын
Is there a video on how to fix the blade angle? The cutter I'm using cuts crooked by 1/16 of an inch.
@jessicaosburn8644 жыл бұрын
I don't think we got the blade holder thing in our box - is there a way to remove/replace without it?
@hfshardwarefactorystore22294 жыл бұрын
The blade holder is now the lid of the "toolbox", just flip it upside down.
@ricacamiyaya3 жыл бұрын
thank you so much!!!
@dalesusanmerrill30013 жыл бұрын
Great video! Thank you! This is my second time adjusting the blade and I thought I remembered how to do it. So I turned the allen wrench bolt next to the two bolts you're supposed to turn. Now, the clamp will come down straight until I crank it down hard. Then one end starts rising again. Did I break it? Is there a way to fix that? Thank you!
@major2525 жыл бұрын
can you show how to align the balde to 90 degrees with the back stop so the cuts are perfectly square???
@hungwanyiu Жыл бұрын
Where could I buy the blade holder?
@Loftenaturalcare8 жыл бұрын
when are you going to have this paper guillotine back in stock?
@tinybim669ify3 жыл бұрын
When I adjust paper clamp and tried to tighten the 2 bolts 1 of them was stripped out from the factory. How can I get a replacement plate?
@johnd12165 жыл бұрын
How do I cut small sizes precisely? For example .56 inches.
@robinpetrina69457 жыл бұрын
So I am leveling the clamp and I did exactly what this video says, but when I camp on to paper and tighten it, one side of the clamp becomes unlevel therefore not holding the paper, what shall I do??
@hfshardwarefactorystore22297 жыл бұрын
Hello, It's possible that the metal piece is broken, you can take it off all the way and inspect it. If so, contact us through our website please. Also make sure there is no grease on it that would allow it to slide, and make sure the screws are tightened very hard when put back in. Sincerely, HFS
@davidberndt62757 жыл бұрын
Is there any way to adjust the blade to be more parallel the the cutting pad? I have the 17inch model and the first 7 or 8 inches cut fine, but I have to apply quite a bit of pressure cutting quite deeply into the red pad. The blade won't come in to complete contact with the pad from about the middle on back.
@HardwareFactoryStore7 жыл бұрын
Hello, Yes there is. Follow the same method above for removing the side access panel. Once that is off, look at the back of the cutter and you will see a silver plate with three bolts aligned vertically. If you loosen the top and bottom bolt only, the entire plate and hinge will be able to shift up and down to level the blade. Note that on the top of the silver plate there is a small set-screw, which may need to be adjust as well. This set screw acts as a stop against the frame to make leveling easier. Sincerely, HFS
@davidberndt62757 жыл бұрын
That worked! Thank you!!
@ZobiLaMoucheLeRetour7 жыл бұрын
Thank you very much too ! Worked for me too !
@jesusa.castillo47246 жыл бұрын
Thank you!!! Really easy to do with your help.
@michaelbelfer16924 жыл бұрын
Jesus A. Castillo should there be slop at the end of travel?
@aetherprintingservices5 жыл бұрын
What do you call that red plastic bar that the blade hits when cutting? Mine is already grooved and damage, I need it replaced.
@galvosaur3 жыл бұрын
CUTTING STICK -- mine is all damaged too and I'm trying to remove it but the thing is STUCK :(
@lovablelilac91323 жыл бұрын
@@galvosaur There are two bolts underneath holding them in place! So frustrating until I found those.
@gabriellamcnevin18585 жыл бұрын
THIS IS A HUGE PROBLEM. I got this machine a week ago and the clamp became misaligned the first night I used it. I followed the instructions to fix the problem, but could not achieve 100% alignment. After following these steps, I achieve around 95% alignment. 3 days later, I used the machine again. After cutting 5 sheets of paper, I found that the clamp was (again) VERY misaligned. I’m so disappointed with this machine. It’s disappointing for 2 key reasons. 1) the frequency in which the clamp becomes misaligned and 2) the inability to fully correct the problem. The likelihood of experiencing one of these problems should deter someone from buying it. The likelihood of experiencing both problems is outrageous.
@gabriellamcnevin18585 жыл бұрын
The base is not flat.
@hfshardwarefactorystore22295 жыл бұрын
Gabriella, I am sorry to hear about the trouble you are having with our cutter. Doing this process once should fix it permanently, it sounds like there must be something else that is causing the issue you're having. If you could please contact us through our website we'd be happy to offer additional help, or send out a replacement cutter if needed. hardwarefactorystore.com/pages/support Sincerely, HFS