Hilti Demolition Breaker model TE1000AVR _ ( Maintenance Operation )
Рет қаралды 85,774
10 жыл бұрынHow does the maintenance of Hilti Demolition Breaker Model TE1000AVR
ٌُReset And Restart the basic electronic circuit, which is responsible for the operation of the working system Demolition breaker, without the need to use the device Agency, an innovative and simple solution
by Ahmed Jehad Najeep
visit us on website www.npt.najeco.com
TE1000AVR عملية صيانة للكسارة ماركة هيلتي موديل
تصفير وإعادة تشغيل الدارة الالكترونية الاساسية المسؤولة عن تشغيل نظام عمل الكسارة
دون الحاجة لجهاز الوكالة ، وبحل بسيط ومبتكر بواسطة أحمد جهاد ىجيب
@Mirou-bboyingSamir 4 ай бұрын
شكرا جزيلا والله التجربة فادتني و الحمد لله و بارك الله فيك
@user-gh7nn3pq8e 3 жыл бұрын
الله يزيدك من فضلة استاذ احمد
@TheCommentsMaster 7 жыл бұрын
I have an old hilti TE60 bought in a car boot sale for about $100 It has a theft protection system light on that stops it from working and I have no fob key to activate it. I don't want to go to hilti as they charge a lot of money. Any suggestions before I throw it to the bin?
@rocsvt1 7 жыл бұрын
do you work on wacker eh65 hammers
@jeffmagid8333 6 жыл бұрын
Does anyone know where I can get parts for a HIlti TE 805 demo hammer
@krzysiupiontek9767 3 жыл бұрын
When you hover over the red lamp with the laser, the lamp goes out and after some time it lights up again. What to do ?
@christianhabetswallner7402 8 жыл бұрын
how does it work on Hilti te70?
@jhonmares1329 6 жыл бұрын
MUCHAS GRACIAS, ESTUBO MUY BUENO EL VIDEO, COMPRE UN HILTI 3000AVR Y OJALA NO ME APAREZCA ESAS LUCES ROJAS, Y SI APARECIERA ESAS LUCES PROBARE SU ENSEÑANZA....MIL GRACIAS.
@manuelbriceno4051 5 жыл бұрын
Que hiciste con el 3000 yo tengo con luz encendida y no funciona el truco. espero me puedas ayudar
@muhammadfarook Жыл бұрын
www.youtube.com/@HILTI.Pakistan Hilti unlock device SRT reset tool available here connect
@b3safe 9 жыл бұрын
thanks for this informational video but i kind of did'nt get what u did there... all i understood was u pinted the laser at the red light and u reset it.... so if its that simple, do you really need to open the tool to do what u did or can u do it with the tool closed up and point the laser at it from the outside? Looking forward to hear from you. thanks
@AhmedJehadNajeep 8 жыл бұрын
+Mouad Rachidi Welcome Mr. I will answer your question: ( do you really need to open the tool to do what u did ) I have been working in the maintenance center, and when the customer brings his machine, in order to repair it, we dismantle and analysis of faults in it, and in any case I will soon upload video on KZfaq, explain the method and system work fot TE1000 AVR , and please visit our site maintenance, in order to understand my intention and my goal of video publishing www.npt.najeco.com
@premjibhudia4480 2 жыл бұрын
I have taken out wires to repair blue wire from connector and forgot where it came out. Would you please let me know where to they go in connector
@irfanabdulqayyum2637 6 жыл бұрын
Asslam o alaikum brother i m also working in a tools service center can u tell me plz where do i find the control board of te 1000 avr i have 12 piece to repair help me out please ,thanks
@nunoferreira1842 7 жыл бұрын
hello, where can I find schematic board , You provide?
@joserojas9931 7 жыл бұрын
Si funciona, yo tenia un te60 y el único problema que tenia es que se había dañado el cable de corriente, todo lo mecánico estaba en perfectas condiciones, solo le pase el láser y funciono. gracias
@manuelbriceno4051 5 жыл бұрын
Broder tengo un th 3000 ya lo hice y nada espero me ayudes urge
@edwinponce1 3 жыл бұрын
@@manuelbriceno4051 lo boy a intentar yo tengon un t500
@manuelbriceno4051 3 жыл бұрын
@@edwinponce1 que tengas suerte bro!
@reydiazperez3053 Жыл бұрын
A mi no me funciona
@abdessattarfytahi7830 3 жыл бұрын
السلام عليكم ورحمة الله وبركاته اخي ممكن طريقة صنع جهاز اعادة تشغيل الدارة الرئيسية
@electromecanicaeltaller422 7 жыл бұрын
Estimado, soy de Argentina y tengo un problema con el martillo Hilti TE-706 AVR. El fallo es que al intentar encenderlo intenta arrancar y se para (la mecanica esta en perfectas condiciones) luego enciende la luz de servicio. Muchas gracias desde ya, saludos cordiales Simon Herrera. Dear, I'm from Argentina and I have a problem with the Hilti TE-706 AVR hammer. The fault is that when trying to turn it on it tries to start and stops (the engine is in perfect condition) then turns on the service light. Many thanks from now, best regards Simon Herrera.
@edilsonreis8498 8 жыл бұрын
OLÁ AMIGO EU FIS COM UM LESE DESSE MESMO JEITO AI EM UM DO MESMO HILTI TE 1000 AVR, SÓ QUE FUSIONOU E DEPOIS PAROU NÃO QUIS FUSIONAR MAS NÃO,O QUE SERÁ QUE PODE SER ?
@manutencaonapratica2396 5 жыл бұрын
Boa noite amigo e o seu comentário eu estou com uma máquina dessa mesmo com esse mesmo problema fiz mesmo procedimento aí do vídeo com laser e nada foi resolvido não consegui êxito nenhum encontro com a máquina parada e a placa não tem possibilidade de recuperar ela porque dá é coberta com a Regina plástica não sei ponto a máquina parada e uma placa dessa muito cara ele funciona ou também fiz com LED e acendeu as luzes apontei o laser na direção do EDGE funcionou e depois parou não funcionou mais souber de algum resultado aí você fala para mim valeu obrigado aí uma força
@user-gh7nn3pq8e 3 жыл бұрын
عندي هيلت نفس الموديل فية مشكلة في القطعة الاكترونية كيف اقدر افحصها
@dareksieron61 4 жыл бұрын
How to reset red light on TE 905 ?thx
@mohammedchouarfi8508 5 жыл бұрын
chokrn
@senolkaytanl4013 7 жыл бұрын
Hi, what about TE 3000 AVR, I have the same issue, I turned off the red light with laser, but I couldn't make it work. Is there a different way to fix that or something I ignored.
@AhmedJehadNajeep 7 жыл бұрын
Şenol Kaytanlı no, you have done all you can do , they work at the same principle they have SR motor ( switched reluctance motor ) i think there are problem in the way of work because there is a lot of electronic element in the main board and when the breaker get working , the electric elements separated from it's places , and the selecon material where but on the board , prevent you to fix any thing so it big mistake and Hilti ignore that . thank you again
@sdilan80 7 жыл бұрын
Ahmed Jehad Najeep a
@davidram1974 6 жыл бұрын
Eliminate the circuit board and connect it cable cord to the switch. It will work
@ameerqassas 4 жыл бұрын
@@davidram1974 do you have more info how to do that plz
@muhammadfarook Жыл бұрын
www.youtube.com/@HILTI.Pakistan I can provide you if you need hilti srt device unlock all model hammer drill electrics card
@riko2186 5 жыл бұрын
how to get around hilti tps ?
@AJ-he2el 7 жыл бұрын
good
@154electrician 7 жыл бұрын
Ananthraj Raj did it work?
@ravikumarbanshiwal1781 9 жыл бұрын
thanks sir for sharing such rare information, however can you tell me which kind of laser light is required to reset circuit board of TE1000AVR.
@AhmedJehadNajeep 8 жыл бұрын
+Ravi Kumar Banshiwal any one red thank you
@HILTi.Pakistan Жыл бұрын
www.youtube.com/@HILTI.Pakistan
@muhammadfarook Жыл бұрын
www.youtube.com/@HILTI.Pakistan Hilti unlock device SRT reset tool available here connect with me on this number
@HILTi.Pakistan Жыл бұрын
@@muhammadfarook www.youtube.com/@HILTI.Pakistan
@edgaradriancastroguzman6143 6 жыл бұрын
the good gear system and where the piston goes uses oil or grease on a hilti TE_1000_AVR
@enzocirino2394 5 жыл бұрын
How to reset red light on TE 905 ? TKS
@artthemandan 8 жыл бұрын
It worked for me, but what I had to do was to take the laser and point it across the opening back and forth. The light shut of right away.
@bertoloche 7 жыл бұрын
Dan Nordoff can you explain a little more about the presses you did ?
@CSJiGSaW08 Жыл бұрын
can you explain???
@antonypolosalas1270 7 жыл бұрын
WORK WITH THE TE 70 ATC ??
@muhammadfarook Жыл бұрын
www.youtube.com/@HILTI.Pakistan Yes and connect with me on this number
@eliasel-khoury6821 5 жыл бұрын
i had the same problem and i also tried solving it with a laser annd it worked aslong as it is still plugged in. as soon as you unplug it and replug it again the light goes on again and have to laser restart it again.
@syte7544 4 жыл бұрын
i have same problem did you find a salutation ???
@paulokljajic4716 2 жыл бұрын
@@syte7544 hello did u find salution?
@muhammadfarook Жыл бұрын
www.youtube.com/@HILTI.Pakistan Available here it's salution
@hishemovitsh3986 7 жыл бұрын
العملية ضبطت معايا بس ما اشتغلت ايه هو المشكل؟
@joseeduardorios9256 7 жыл бұрын
buenas tardes como estas ese aparato es un laser comun
@HKRChanel 7 жыл бұрын
صديقي بتزبط على كل الانواع هاي الطريقه
@AhmedJehadNajeep 10 жыл бұрын
ابتكار طريقة لتصفير وإعادة تشغيل الدارة الرئيسية المعقدة المسؤولة عن تشغيل نظام عمل الكسارة الهيلتي موديل TE1000AVR فخر منتجات هيلتي الالمانية Innovating a way to reset and restart the main circuit complex is responsible for operating the system work Demolition breaker Hilti Model TE1000AVR, the pride of the German Hilti products visit us on website www.npt.najeco.com
@frankcolon8156 8 жыл бұрын
What about the 905. Will the laser work?
@jamalfarra36 6 жыл бұрын
عندي هيلتي موديل te706avr مزوده بداره الكترونيه بلداخل .لما اشغلها يشعل الضو الاحمر بلأعلى وماتشتغل .فكيتها وماعرفت سوي اي شي .ممكن المساعده
@jamalfarra36 6 жыл бұрын
رقم الوتس اب عندي 00971506645459 ولك الشكر الجزيل
@syte7544 4 жыл бұрын
i have same problem and i also tried solving it with a laser and it worked but as soon as you unplug it and turn it back on again the light comes back on again ................. Any one found a salutation.
@perfecttoolrentalrepairinc3564 9 жыл бұрын
DO U KNOW HOW TO ٌُReset And Restart the basic electronic circuit FOR TE 706
@AhmedJehadNajeep 9 жыл бұрын
you welcome i think it's the same way That you see in this clips
@marcoalmeida3351 9 жыл бұрын
Ahmed Jehad Najeep I've done what is in the video, but when I unplug the power supply and I switch back on, turn the red light
@AhmedJehadNajeep 9 жыл бұрын
This means that the fault in the main circuit and not in the reboot circuit and in this case you have to change the main circuit, and nothing to do but change the main circuit good luck
@AhmedJehadNajeep 8 жыл бұрын
+PERFECT TOOL RENTAL & REPAIR INC. its the same thank you
@elrincondelmecanico 3 жыл бұрын
Marco, were you able to reset your 706? how? I have one with the same problem as yours
@liridonaterstena2980 8 жыл бұрын
hallo I am from kosovo I servising hilti watched the video hilti TE1000 avr all hilti valid for a lazer to the code or only for the 1000avr hilti please help me
@AhmedJehadNajeep 8 жыл бұрын
+Liridona Terstena I will send you to schemes for Hilti breaker by e-mail Send me your email address to communicate thank you
@liridonaterstena2980 8 жыл бұрын
Email : dona.gazi.87@gmail.com Thank you
@AhmedJehadNajeep 8 жыл бұрын
+Liridona Terstena it work with many model like te706avr so the test is better way to insure
@jojo-zd5yj 8 жыл бұрын
hello, What power for the laser, please?
@AhmedJehadNajeep 8 жыл бұрын
I think if you can get lazer pen with 1mw power and 630-680 nm it's good enugh
@jojo-zd5yj 8 жыл бұрын
OK thanks ,I'll try on a 70 atc
@007TiFi 4 жыл бұрын
Did it work?
@syedaliabbas2476 3 жыл бұрын
it can not possible to reset the tool Hilti breaker with any "red light". And if you see that man shown not only one video but it compiles two videos of Hilti breaker
@HILTi.Pakistan Жыл бұрын
www.youtube.com/@HILTI.Pakistan
@muhammadfarook Жыл бұрын
www.youtube.com/@HILTI.Pakistan Hilti unlock device SRT reset tool available here
@leewalker1327 7 жыл бұрын
the service indicator/light is an indication that your tool needs serviced not that the light only needs reset. would you do that with your car...no. send the tool to hilti for a professional repair and you will get a warranty with the repair. Yes you will reset the light but your tool will only lack performance and lead to a more costly repair in the future. this guys tool in the video really needs a repair or service.
@hamda422 7 жыл бұрын
مش عارف ايش بدّي احكي
@claudioreggianini5845 7 жыл бұрын
HI DON'T WORK ON HILTI TE50
@ramijedidi1510 8 жыл бұрын
you can stop red light flashing for couple of minute. Ok but you can't reset the TE 1000 with this china laser delete this rare video
@AhmedJehadNajeep 8 жыл бұрын
+Rami Jedidi According to your comment ( you can stop red light flashing for couple of minute. ) I have succeeded and resolve first problem and no need to (delete this rare video) thank you
@joseeduardorios9256 7 жыл бұрын
buenas tardes como estas ese aparato es un laser comun
ISSEI / いっせい
Рет қаралды 81 МЛН
Fabiosa Best Lifehacks
Рет қаралды 38 МЛН
Hilti.Pakistan
Рет қаралды 131
Hilti TE 1000 AVR Red Light Problem Reset with WiFi Reset Tool SRT Command. with .Android. Mobile...
Hilti.Pakistan
Рет қаралды 1 М.
Wrecker
Рет қаралды 362 М.
notebook-31
Рет қаралды 41 М.