What the fuck did you guys expected him to build tiger tank? For a home build this is awesome.

Looks like that track needs some more tension.

Sergey Bondarenko 53 seconds ago Hello my dear friend designer. Put a caterpillar tensioner on your machine, otherwise the caterpillars will be constantly snacking. The upper support rollers are very narrow, make them wider otherwise the caterpillar may just fly off. The design is very interesting, but the transmission is very weak, the belts will wear out very quickly. Put an automatic clutch, for example, from a snowmobile or a full-fledged clutch from a car. use the gearbox to humiliate the gear ratio, because the engine is very weak and the EMU is complex to move such a structure, and on turns it stalls in you. And you will be happy

And I'm waiting for a new video. You can't leave us waiting like this! Lol

You need chain tensioners...The 2 rims on the rear should be able to slide in and out and be spring loaded to take the slack out of the track chains

English at bottom. Ведущее колесо должно тянуть гусеницу, а не толкать ее. Также нужны гусеничные натяжители. Сделайте переднюю часть задней, переверните дифференциал, поменяйте местами ведущие колеса слева направо. Чем больше веса вы добавите, тем хуже будет проблема, если вы не сделаете это сейчас. Продолжайте в том же духе. Надеюсь это поможет. The driving wheel needs to be pulling the track not pushing it. It also needs track tensioners. Make the front the back, flip the differential over, swap the drive wheels left to right. The more weight you add the worse the problem will be if you dont do it now. Keep up tho good work. Hope this helps.

i think we are all waiting for part 9 and waitng for him to add armor and turret

You really need to install track tensioner or shorten the track. I also suggest you look at installing up to 3 additional support roller wheels on the outer edge of the top (under the track) to keep the track from leaning to the outside. Great job overall.

Track tension required. Adjust the rear sprockets

I can't understand if you've already said it, but those tracks could do with tensioners. Otherwise, great test!

You need chain tensioners...The 2 rims on the rear should be able to slide in and out and be spring loaded to take the slack out of the track chains. They are going to stretch a bit as well and it will make the tracks run smoother :) Looking forward to the next Vid. :)

good, now make a T-34

Парень лёгких путей не ищет! Голова светлая и руки прямые,молодец!!!!!!

I have a homemade heavy tank ready to storm Albania. Not sure how to get it to Europe though.

Очень хороший аппарат! Главное практичный! Только гусянки чуток надо будет подтянуть или установить натяжные катки и будет вообще супер! Таким вездеходом можно даже поле пахать! Молодец - голова работает как надо и руки растут откуда надо! 👍👍👍👍👍👍👍! Моё вам уважение!

Kawał dobrej roboty!! Gratulacje pomysłu i wykonania!!

Gdy World of Tanks wejdzie za mocno :D Super robota

10:49 - "next video is coming out in a week or two" =(

You really need a track tensioner and an upper trail rail. Good job tough !!!

Вы молодец! Но для правильной работы вам необходимо увеличить натяжение на траках путем удаления звена! И все должно работать правильно. Удачи!!!

Лайк однозначно..,(хотя конечно же парню изначально надо было посмотреть как натягивается гусень на тракторах или танках... без амортизации можно только до магазина доехать...обода колесных дисков разьебутся через пять км бетонки или 15 км грунтовки..) ,но парень молодец.!

I was wondering why he made the tank front drive. Because of all the tanks that I have seen they have had the drive wheels at the back. It would be easier and a lot less work if he just turned the controls and engine around. So the tank pulled the tracks under the wheels rather than pushing them over the top of the small wheels. Well I ges you live and learn. But its still cool to see something built in a small garage.

Brother, you got serious skills!!. Very impressive. I just watched the motorcycle build the other day and that was impressive. And then I see this...Wow! You have the gift of patience and talent thats for sure. Bravo again!!!

Bạn rất sáng tạo rất tuyệt vời 👍

Ajde do 1 miliuna subova Sretan božić

Nice build. You need some way to take the slack up on those tracks. There seems to be too much track on the left side for sure. Can't tell about the right side because the left side is shown more. But interesting build all the same... Thumbs Up!

That young man is very technical smart he got the very basics down way to go

9:39 was a smile bringer. And also ringtone greatness.

молодец парень,минусов конечно много,но для твоего возраста это приемлимо,остальные косяки доработаеш со временем,молодец что дошол до конца и не бросил своего гусеничного коня☝️💪👍👍👍👍

Poz iz Dalmacije drago mi što i Hrvati imaju KZfaqra koji ima milion preplatnika svaka čast. 👍🤚🥂🍾

Koliko si ti zapravo gotivan tip. J svaki dan gledam tvoje izume i pokusavam isto kao i ti . Svaka ti cast. :)

Very interesting mini series enjoy watching this vid a big shout out from the UK peace out boys and girls stay safe wherever you are in this planet

Homemade helicopter next 😂

everybody gangsta until this shows up in the batllefeild.

this shows the value of engineering work. It allows you to avoid problem in the future.

Совет: сделай два ряда резиновых колёс, чтобы гусеници лучше держались и их не перекашивало

Might help if you could tighten the tracks a bit---add a tensioner.

Need to put a tensioner system on the tracks and you should be good to go on the lower half. Good luck with your adventures.

Track tensioning, drive teeth are problem areas . Tanks usually have the drive sprockets in the back, not in the front. Spin the driveshaft the opposite way, and turn the chair/ controls around. Consider adding a roll bar,too. Otherwise, great job !

BRAVO MY FRIEND! Tank drives always used a toothed drive gear to stop track bite that you experienced and all tanks experience some amount of track sack as you apply torque to the track usually in reverse so they rarely back up perfuring to just lock track turn the tank. Agine BROVO!

Should have put the drive wheels in the back. Nice build.

The tracks are loose. You need to shim out the rear wheel.

Instead of metal link style track like a bulldozer, I would've used rubber belting and cleats. No slip on the drive sprockets, less weight, etc. A small 2wd truck with open differential would be the entire driveline needed, just separate left and right brakes for steering much like the ripsaw tank vehicle driveline. Except the tracks would be more like a pistenbully or prinoth. You'd also have reverse. I like your videos anyway, keep up the good work man, very talented.

Ciao, hai fatto un lavoro da ingegneristica complimenti .

How to make this tank run properly. 1) All 6 wheels should not completely touch the ground at the same time. The front and rear axle should be mounted slightly higher off the ground than the middle axle. So the tank teeter-totters a small amount on the middle axle. 2) Connect the drive shaft and brake calipers to the middle axle. 3) Slot the frame where either the front or rear axle mounts. The same way the wheel on a bicycle mounts. Use a heavy duty spring pushing the axle towards the rear of the slot. EXPLANATION: Moving the drive shaft and brakes to the middle axle will make it easier to turn the tank somewhat in its own tracks. By making the center wheels always in contact with the ground more than either the front or rear wheels, means less resistance trying to turn all 6 wheels. Plus less strain on the motor by placing the pivot point in the center of the tank. Rather than the pivot point be at the front or rear axle, as it is currently. Slotting the frame for the axle will force tension on your tracks, while eliminating the slack. It also allows a little bit of give so you won't break the treads upon heavy impact with obstacles. The spring is not required. But if used, the spring has to be extremely hard in order to maintain enough tension on the tracks. PEACE!!!

U need to take a few links out of the tracks they are too loose that's y they catch

Thanks for sharing such wonderful content with your audience. It is very interesting stuff. I appreciate all the work put into it. Sincere thanks!

Well done! you have real talents, only advice i have got is swap the axle over 180 and turn your seat and controls the other way, it will work 200% better, keep it up its good to see young people playing with their hands :), we dont see a lot of this in the UK anymore.

Tracks are still too loose!?

Чувак , сделай натяжитель гусеницы . Обычный длинный шток или болт с гайкой и скобой . Будет легче натягивать .

Hey young man; I love your build. ..just looking at your thumb-nail image; i think you should put some (maybe 4) wheels to carry the tracks. What I mean is, between your tire-wheels.. -- have fun, friend & take care. Merry Christmas to ALL..

Hola amigo, yo le sacaria las ruedas de goma, hacen que la cadena quede torcida, de a poco va a ir quedando, te felicito!!!

Update us man. Miss this thing. Want to see it driving

Столько труда впустую, нет положительного результата.

This guy had to have grown up on a farm..... His fabrication skills are amazing...!!!!

Definitely need to tighten up those tracks. Theyre so loose!

My friend, You should add a track retention to adjust the tension of the tracks. (like real tanks have)

Great job! You've managed to engineer a pretty good homemade track drive. I would suggest that you stagger the bogies so that it supports the top part of the track better. Look up the German Panzerkampfwagen VI Ausf H for ideas on what it should look like.

I'm making one of these too, but very different. It's intended to be street legal and travel on freeways. Currently I'm in the process of manufacturing and machining all of the parts for it.

Brilliant young man...I wished you can build the body too. I like it a lot. Thank you.

You need track tensioners. A gearbox and clutch still wouldn't hurt either. Otherwise well done!

The tracks are way to loose, and you should do away with that whole pully system and change it to a belt drive like a snow mobile would have

Svaka cast, momak je genijalan!

Find a motorcycle gearbox and put it on between the engine and the big pulley! + you can adapt the clutch cable to your pedal

You should turn the driver's seat and engine by 180 degrees, well, and move the control levers accordingly. The driving axle should always be the rear one, not the front - just compare the tension of the tracks and steering in both variants.

Teacher: "What did you do for your holiday?" Student: "I built a tank" Teacher: "You have a vivid imagination. No, seriously, what did you do" Student" "No. Seriously."

the tracks seem loose and wobbly on the bogies. I know you need *some* slack, but is there any way you can tension them up just a bit?

Peace be upon you and God's mercy and blessings be with you Azzouz from Saudi Arabia

Drago mi je što lajkuje samo balkanske komentare 😂Dobar video sprdnjica

I get the impression, that the motorwheels should be at the back of the vehicle, so that the caterpillars could be tight at the bottom and loose on the top.

Great build, tension the tracks a bit more, they seem loosen

I have Loved watching Your Creativity in the Construction of Your Mini Tank . I have designed and built parts used in both the U.S.A. space program for the space shuttles and our Missile systems. And I Extremely miss building and creating fun projects ! Been Retired since 2002 ! Also a Master Gunsmith Armorer ! So I Really am hoping your planning on mounting some type of firearm to it hopefully a nice belt fed machine gun . Should be fairly easy to find one in that part of the world . Best of Luck to You !!!

Нет натяжения гусениц. Разверни конструкцию задом наперед, что бы ведущие колеса были сзади, тогда гусеница будет всегда натянута.

Prijatelju, pratim tvoj projekt od početka, lepo si ti ovo zamislio ali imaš par konstruktivnih grešaka. Gusenice nesmeju da ti budu labave jer će pri prvom naglom skretanju spasti, moraš da napraviš zatezač gusenice na kontra točku od vučnog, slično motornoj testeri. Meni se to jednom desili na vojnom guseničaru po zimi i blatu do kolena.. 😂 Prilikom kretanja gusenica treba da se zateže preko ove tri donje felne a ne preko malih pasivnih točkova. Razmisli o tome da samo sedište i komande okreneš za 180 ° tako da ti vučni točak bude pozadi. Lepo se odmori i proslavi praznike, jedva čekam da vidim kako ćeš da finiširaš mašinu

Super, samo moras zategnuti gusjenice i izvuci dva gumena tocka malo prema vani jer ti gusjenice padaju sa strane, pri vecoj brzini bi to mogao biti problem. Sve u svemu mlad momak a takav projekat, svaka cast!

good job. keep up the good work and keep building.

Very good work my brother! Respect from Bulgaria 🇧🇬👌

Yes, tracks are a bit too loose.

You changed to a bigger, double ridge pulley. Good! Just asking. Can we use one with " teeth" to engage with the power shaft ?

Good work sargent.... now we need sentry gun for it.... 😂😂😂👍.

ponoviću: ne mogu pogonski točkovi biti napred,moraju biti zadnja dva a ne prednja,zbog zatezanja samih gusjenica,u svakom slučaju pohvaljujem tvoj rad,pozdrav!

You've done an excellent job you are very skilled thanks for sharing this build with us.

Maybe more springs because it's going to get heavier! Please make more vids as this one of the best channels!!!

You need to turn seat and controls 180 deg. Drive wheels should be on the back of the tenk to pool tracks.

Trebao bi izgraditi poklopac, ali osim toga izgleda stvarno lijeeeeepo👏👏👏

When will you finish the tank?

Amigo Doctor D. S. muchisimas gracias por tu video!!!! aprendí mucho!! lo que hay que hacer y lo que no hay que hacer!!! un fuerte abrazo desde Argentina!! Друг доктор Д. С. Большое спасибо за видео !!!! Я многому научился!! что делать и чего не делать !!! крепкие объятия из Аргентины !!

Very nice job .Thanks from Poland :-)

do you have reverse? and as others have said tracks too loose.

wonderful work! greeting from Japan

Muito massa esse projeto... estou acompanhando dês do começo !!

Doctor D.S.: What do you need? Everyone: Tanks, lots of tanks...

It cant turn can't it. I suspect that is why it has not received an update.

This Really needs a Mk 19 Grenade Launcher is a 40 mm belt-fed !

I think a sprung track tensioner might help

Lastima que no estés en España, compartiríamos hobby por estas maquinas!!!

Them rubber tires whey don’t you space every other one apart so the first one is touching the inside of the track and the second is touching the outside of the track and so on? That way the track won’t sag (be uneven) over the rubber tires! Or even better double up each tire!

all the way to the end.. you great man watching from Kenya

Главное, далеко от гаража не уезжать)))

que buena creatividad .hombre futurista bienvenido al mundo Felicidades desde Colombia