You should have a clutch pedal and when you push the pedal in it loosens the belt. You would also need a way to lock the clutch pedal down for starting and getting off the go-kart while it's running. I think that would be better than having to hold your lever up to keep moving.

Your arm is now the clutch spring. Wow.

يعتيكم الصحة ولاد بلادي Bravo 😍😍

For any of you who might use this design, remember to put the tensioner so it pushes against the part of the belt that is going from the engine to the wheels. Don’t do it like this guy did, he put it on the part of the belt going from the wheels to the engine.

Buen trabajo saludos desde Ricardo palma - Huarochiri

Good work, try to improve clutch system by preventing heat , noise and neutral friction (at N position of gear ).

Just found your channel and Subscribed. Nice work

Awesome

Good job keep it up.

Your work is good, well done. I congratulate you on this ingenious skill. I love you. I will support you with a like and a subscription to the channel, and I tell you to continue.

good keep it up.. but for more, take out the govnor and slap a new carb for more power... by the way try making the lever a foot paddle to the accelerator

chế giám bằng chan thì ok

Te felicito muy buen trabajo sigue adelanté

Mantappppp

Not bad at all. A small gearbox with reverse selector will give more torque and reversibility. Good work.

I love your work n thinking. I'm dyslexic so don't take me wrong. Ur doin everything backwards Ur clutch or pressure wheel needs to be creating pressure from the outside of the belt n from the. Slack side. Not the pull side. this creates easier tension and more tension

e uno dei veicoli più straordinari del mondo il prossimo video al mcdrive

Put on a centrifugal clutch to avoid burning up the belts put the tensioner pulley on the out side of the belt with a spring keeping tention on it and use your string the same then add a rear sprocket from a mountan bike and boom you got yourself a 7 speed go cart

No reverse?

Good

So essentially what you just made was a belt dive that wants to blow itself up? Because that belt tensioner is 1 tensioning the wrong side of the belt, and 2 tensioning your chain, and the Fact that you could have just fixed and the spinning components to one place, and made your belt tensioner what gives you engagement, your set up would be way more reliable, and also, that's not a clutch, it's a belt drive

Прикольно наблюдать как в 21 веке делают технику из 19 века

Based

if stepped on is much better and easier . keep it up bro

One hand drive ?

Couldnt be a better commercial than the maybelline commercial here..

I wonder if the belt is gonna last for 2 days without breaking due to friction?🤔🤔

Nyimak bosku

👍

Esse cabo estivador de Correia era para ficar junto com acelerador!

Basic clucth like in the car manual transmision

O meu amigo o pedal de acelerar tem que ser no pé você tem que ter as duas2 mãos para para a direção está e a regra ok mano ???

No. Pulley goes on bottom of that belt, NOT 'pulling' side. Also, how is it that all these (offshore) videos have real honda engines, yet U.S.A. Stuck with Chinese predator knockoff type? Comin home to roost,I guess..

Which car parts

Натяжитель ремня не правильно поставил,с верху матор сам тянет .или он хочет перетянуть матор .

Some squeal off the belt on start off My old castle garden lawn mower had that system. 20 years ago worked much better I though he was making a clutch. Not a belt burner Back to the drawing board for the reinvented wheel going soon

how did you make that adapter for the crankshaft?

You should make it longer no leg room.

You should push down on the belt rather than pull up on it... creates more belt in contact with the pulley.

Podia ter colocado motor de moto já com a caixa 🤷🙄.

Where are your old BMW restoration vids

I like this except I think the belt tightener idler should come up from the bottom. That way you get a better grip on the small pulley. I think the belt tensioner should be activated by a foot peddle or a lever that stays tight once it is pushed or pulled over so far.

This kind of cluch is not very Well,but you can turn it better.

Clutch? Looks more like a Jack Shaft tensioner system like on a cheap mower. But hey got the views I suppose🤷🏻‍♂️

Ресурс - 50 км

You should have reverse the whole procedure to wear when you let go it engages the number 2 it should have been a foot pedal

Junior s ilva moto

Pretty useless in fact that there are centrifugal chlutches and torque converters for these engines..

That go cart is sketchy

Aliminyum kasnak kullanmalisin... demir kasnak kayişi yakar 😉