this is how was built my homemade towable 360 degrees mini excavator.
Пікірлер: 49
@melarigata Жыл бұрын
Μπράβο. Τηλέφωνο επικοινωνίας.
@XristosQsisDIY Жыл бұрын
Σε ευχαριστώ πολύ.στειλε μου e-mail sto kiousisx@yahoo.gr και σου δίνω τηλ
@MINItraktor1967 ай бұрын
😎👍👍👍
@user-bu9yy4ks1c2 жыл бұрын
Πολύ δουλειά έριξες αλλά το έκανες σαν να βγήκε από εργοστάσιο 👌
@XristosQsisDIY2 жыл бұрын
Σε ευχαριστώ πολύ !Σαν πρώτη προσπάθεια και χωρίς γνώση στα υδραυλικά είμαι πολύ ευχαριστημενος με το αποτέλεσμα.βεβαια είναι στο πρόγραμμα να κάνω κάποιες βελτιώσεις που θα ανεβάσω φυσικά καθώς επίσης και να εξοικιωθω με το χειρισμό του
@christianrivera6611 Жыл бұрын
Genial estoy tratando de hacer una parecida podrías alludarme enviándome las fotos q salen en el video muy rápido para cojer ideas grandes
@user-bg1ul8od5c Жыл бұрын
عيز اشتريه بكام السعر الحالي
@ktulu9482 жыл бұрын
Genial
@XristosQsisDIY2 жыл бұрын
Thank you
@TeluguWatcher Жыл бұрын
I planning to make one could you please help me to know about the swivel bearing / slew bearing cost and the center / swivel joint cost and specifications??
@XristosQsisDIY Жыл бұрын
Hello mate.the boom and stick cylinders are 70mm bottle and 30mm actuator with 500 mm run.the bucket cylinder is 60bottle,25mm actuator and 60 run.the swing bearing is based on a car wheel bearing system.and the hydraulic motor i dont know the characteristics.i hve used an big gear module 4 for steady gear and a little one to the motor
@TeluguWatcher Жыл бұрын
@@XristosQsisDIY how much maximum pressure that cylinders can bear upto?
@XristosQsisDIY Жыл бұрын
Now is up to 130 bar because of my pump whitch is a small one
@TeluguWatcher Жыл бұрын
@@XristosQsisDIY is it a gear pump or a piston pump how much lpm it discharges?
@TeluguWatcher Жыл бұрын
I am happy that you reply for my comment these little information is very much to me
@mnb26112010 Жыл бұрын
what size of Boom and arm part?
@XristosQsisDIY Жыл бұрын
Thank you for the comment .It is made of square 100x100mm tube
@mnb26112010 Жыл бұрын
@@XristosQsisDIY Thank you for your reply.
@user-bg1ul8od5c Жыл бұрын
عيز اعرف اعمل وحد زي دي
@gholammoziriyan2493 Жыл бұрын
سلام شماره خریدارم
@user-cx8oc8xx7f2 жыл бұрын
สนใจราคาเท่าไหร่ครับ
@XristosQsisDIY2 жыл бұрын
I just made it for prototype.it cost me 2000- 2500 Euro
@rubelmollah16172 жыл бұрын
Hi
@XristosQsisDIY2 жыл бұрын
Hello my friend
@viping31898 ай бұрын
Do you have the instructions and drawings to share?
@XristosQsisDIY8 ай бұрын
Ι have not plans i built it step by step.it will be my pleasure if i can help only by instructions in every step
@flaviopozzer3 ай бұрын
Hi, could you tell me how you created the 360 degree rotating system?
@XristosQsisDIY3 ай бұрын
@flaviopozzer hello.it's based on a car wheel bearing hub but i suggest you to take from a small truck to be more stable.i want to change it to
@flaviopozzer3 ай бұрын
Thanks and the engine? Is this a normal orbital engine? Have you connected any valves?
@XristosQsisDIY3 ай бұрын
The engine is 11 hp briggs and Stratton and it is connected with a small hydraulic pump.
@offroadadventuresgreece2 жыл бұрын
Άμα έχεις όρεξη , υπομονή και πιάνουν τα χέρια σου!!!
@sirtimidsokasanatha57962 жыл бұрын
ερ - εισαι επαγγελματιας
@XristosQsisDIY2 жыл бұрын
No i am not.i am only a pasionated builder with simple tools
@XristosQsisDIY2 жыл бұрын
Όχι ερασιτέχνης είμαι απλά μου αρέσουν οι κατασκευές.και μάλιστα διαθέτω μόνο απλά εργαλεια