Very nice achievement.This log splitter is effective.Congratulations!
@josevelasco3245 Жыл бұрын
The splitting chamber is awesome
@bluethunder19515 ай бұрын
I like this setup, btw, birch is the worst kind if wood to split its fibres are so long and stringy they tend to stay together. Like other videos on firewood processors nobody likes to show the last piece getting split, maybe because it’s the toughest to control and maybe an embarrassment. But all in all this is a nice processor 👍🏻
@ViralclownАй бұрын
Awesome!
@terryhaldeman1474 Жыл бұрын
This is the nicest processor of this type
@RJM1011 Жыл бұрын
Well done I like it. Thank you for the video. 👍
@outdoorswithlarryrobin Жыл бұрын
Nice work, just subscribed, maybe little more protection on the hoses, Take Care 🚜🪵👍🏼🇺🇸
@brunow61014 ай бұрын
Good design, where did you get the saw and hydraulic motor from?
@MickesDIY4 ай бұрын
Hydralic motor is a secondhand parker f11-5. Saw bar is just a standard bar for harvester
@brunow61014 ай бұрын
Thank you for the reply. @@MickesDIY
@user-pd4we4ev1d10 ай бұрын
GENIUS Thank you
@robmack15110 ай бұрын
Now thats a design that makes sense from start to finish. Would you build another one, or have plans for the one you built? Its much more innovative than anything offered by AVANT, or that ive seen elsewhere. Kudos
@MickesDIY10 ай бұрын
Thank you! I have no plans, I just build it pretty much. It’s inspired by halverson processors but theirs is much bigger and heavier and wouldn’t work on such small machines.
@bartudink689 ай бұрын
This machine is very similar to the BTD saw splitting machine kzfaq.info/get/bejne/nMyBdcd4nq6ldXU.html&ab_channel=MartinBloemenkamp
@Rooftopmatty4 ай бұрын
What are you using for an assembly to run the saw? That’s the only thing holding up my building
@MickesDIY4 ай бұрын
I built it from scratch. One big plate holding the sawmotor with two bolts that locks the last plate. Then a sliding plate with two pins that fit the sawbar and a tension screw, also a coupling for chain oil. Lastly a little plate on the other side of the sawbar with two holes with threads that the two bolts from the sawmotor plate screw into and locks it after it's been tightened. At first big plate, sliding plate, sawbar, little lock plate. In that order sandwich together.
@Murphinator1964 Жыл бұрын
Looks like a Halverson but luv the hyd wedge. Awesome job
@tunintunin34178 ай бұрын
Great build man, I am impressed. I am researching to build something for my tractor, do you have any drawings, blueprints for this you would share, sell? Thank you.
@MickesDIY6 ай бұрын
Thanks! I don't have any drawings. I just designed it as I was building it.
@modyfoxy29906 ай бұрын
great machine:) what hydraulic motor is used with the cutting chains? I have Parker f11-010 it will be ok in my project? Thank you for your help😊
@MickesDIY6 ай бұрын
Thanks! I run with Parker F11-5, if the larger one fits your build depends on what flow you have.
@modyfoxy29906 ай бұрын
@@MickesDIY Thank you very much. You are my hero👏
@magnusolsson864 Жыл бұрын
Grymt bygge 🇸🇪💪
@natrob123 Жыл бұрын
Very nice work 👍🏽 how much do you think it cost you to build?
@MickesDIY6 ай бұрын
Thanks. Haven't done the maths on that 😅 But around 2-3000 euro I think.
@user-xp4yw4cy2r11 ай бұрын
is your f11-05 motor have a 18 mm shaft and how did you fit a sprocket to it?
@MickesDIY11 ай бұрын
Yes it's 18mm shaft. I had a local machineshop make an adapter for me to fit standard harvester sprockets with 25mm hole.
@user-xp4yw4cy2r11 ай бұрын
@@MickesDIY lol was thinking the same thing
@user-xp4yw4cy2r11 ай бұрын
would like to see how you did it or just say how but it would be hard to take picture
@adamzanellato7114 Жыл бұрын
What did you use for your saw motor
@MickesDIY Жыл бұрын
I'm using a volvo/parker F11-5c.
@adamzanellato7114 Жыл бұрын
Where did you order it from
@MickesDIY Жыл бұрын
It's old and used so can't help you with that. Any hydraulic shop can probably sell it.