HONDA CRF LOWER LINKAGE BEARING REMOVAL. BRILLIANT SIMPLE METHOD AND TOOL.

Рет қаралды 24,030

8 жыл бұрын

Just a short video and demonstration showing a simple tool I have developed to push out those internal bearings on the honda crf linkage(or any motorbike linkage). The linkage in the video was already on the bike and in a poor condition of neglect. I replaced the linkage and bearings myself and would never let any components get anywhere near this condition. Hope this helps please share as there's so many questions asked on how to remove them but no definitive answer hence the need to post this video.

Пікірлер: 34

@porter5877 4 жыл бұрын

U just saved me £90 for a motion Pro bearing puller....awesome video

@lorenzkockaerts 19 күн бұрын

i gonne test it right now 8j after video posted still handy very smart hope it works good here ..... it works thx very very ussefull thx allot

@Gyoszor Жыл бұрын

I'll test next week, when my bearings arrive. Thanks for the idea!

@MrXiztence 7 жыл бұрын

WOW you know out of the 15 or so videos showing how to replace the bearings on the linkage, none of the showed how they got these out. Thank you for your genius tool im going to make one as well since my stupid bearings wont come out. Thank you!

@phil9939 7 жыл бұрын

Yes my friend - THANK YOU. After 11 years of neglect of my 05 CFR250R I've has since 2010, I'm finally doing the swing arm and lower linkage. Swing arm bolt was seized but lots of PB Blaster and let still for 24hours and it came out no problems today. Just started doing the lower linkage and the full Honda Service manual does NOT explain needing the blind bearing tool but I just looked at my Clymer and it explains it and I thought this was going to cost me $$$$$$ for the tool. I'm doing this in my back yard and I have access to the redi rod and expansion piece etc for free so brilliant!!!!! All the needle bearings came out in pieces but i'm soaking the old bearings in PB Blaster and will have at them tomorrow. I had a huge crack in the sub arm assembly and bought one of Ebay for $40 CDN and IMO its brand new all the bearings etc are pristine.

@richiperlotti3090 Жыл бұрын

great!! thank you very much!! I've saved money!!!

@SlagathoR45 7 жыл бұрын

Just did this method and worked perfectly for my CRF250X. Thanks Marvin!!

5 жыл бұрын

Don't forget to give the man a thumbs up, Good job and thank you.

@DarrinCJones 6 жыл бұрын

Thank you for posting! Very helpful.

@ralphhill6872 6 жыл бұрын

That's the bomb. 20mm ramset dyna bolt for 2011 YZ 125. Fit into bearing outer after needles removed, then a steel drift (long 16mm bolt) from the opposite side. Slight variation but same result. Thanks heaps.

@user-xz7nb7qs3x 8 жыл бұрын

this video saved me thx a lot

@katiejohns3415 4 жыл бұрын

Brilliant idea thanks

@onlygazza 5 жыл бұрын

Brill idea bud 👍

@EastWolfRiders 7 жыл бұрын

you are the best :D :D thanks for sulution of my problem

@matthewframe6616 6 жыл бұрын

THANK YOU.

@toddmcilroy2759 7 жыл бұрын

Awesome idea! I believe it's a heavy duty concrete wall anchor.

@MegaIcecream13 7 жыл бұрын

yes your correct you can get them in a few different sizes. this is an easy fix

@dirkdiggler9082 7 жыл бұрын

Awesome!!!

@sijmes 7 жыл бұрын

Great stuff, I was trying to punch the both bearings with what I thought was a spacer, all the way through and out. Now I see hat they are blind bearings. Just as well I didnt go and use the hydraulic press at my works ;-)

@sijmes 7 жыл бұрын

M10 was too small for my WR450. Warming up the aluminium with a hot air gun was the key to getting my bearings out.

@MarkNealon 6 жыл бұрын

Inspired by this I went to B&Q... they didn't have these exact parts (no M10 nuts at all!) but I got a 60mm M10 masonry plug which did the trick to get one of the bearings out... unfortunately on the other the lip just snapped off. Nightmare.

@gamz1 7 жыл бұрын

Yep worked great but only with M12 rawl bolt and thread, mine wouldn't come out with M10 rawl bolt, WR250 F

7 жыл бұрын

Uh be damned good job mate

@nickkaplan6585 7 жыл бұрын

what exactly is that M10 plug? I've looked up wall plug, roll plug...can't find it. What is it really used for? thanks! brilliant idea!

@outbackatl 7 жыл бұрын

its called a Rawl Plug

@tempooo31 4 жыл бұрын

it's not a rawl plug ,,,,,,it is a anchor bolt for concrete or red head size m10

@D6onGPS 3 жыл бұрын

Dyna bolt in some countries

@aTcMDaMo 5 жыл бұрын

Anyone in Australia a 20mm x 110mm dynabolt from bunnings is perfect for the lower link bearing cages for crf250 2010, use lots of heat!!!

@D6onGPS 3 жыл бұрын

Wish I read this before I left I grabbed a 16mm which was to small gunna try a 20mm now

@Mamangjangkrik88 2 жыл бұрын

What is the bearing number?

@tazzthedoodle7861 3 жыл бұрын

So now you still need a press to get the bearings installed. So you might as well set up the press to get the old ones out. Good idea tho

@D6onGPS 3 жыл бұрын

You can hit them in using the old race and those bits of timber

@mickeymouse4897 3 жыл бұрын

Animal ... rough as F**K ... could have easily used a longer threaded bar, locked Rawl bolt behind bearing, used a socket as a puller tube, nut & washer & wound it out without smashing a soft alloy linkage into a socket, clearly damaging alloy rocker ....