Honda Magna Carb Rebuild - Installation fixing final touches

No video

Honda Magna Carb Rebuild - Installation fixing final touches

Рет қаралды 8,053

Күн бұрын

╔═╦╗╔╦╗╔═╦═╦╦╦╦╗╔═╗
║╚╣║║║╚╣╚╣╔╣╔╣║╚╣═╣
╠╗║╚╝║║╠╗║╚╣║║║║║═╣
╚═╩══╩═╩═╩═╩╝╚╩═╩═╝
Leave me your thoughts: One of my favorite things about doing this is making connections with so many new people!
* * * * * * * * *
LINKS -
Patreon: / mannymarvelous
Insta: / mannymarvelous
Linktree: linktr.ee/Mann...
* * * * * * * * *
Enter to win my jacket - SUBSCRIBE: to stay up to date and not miss any content!
SHARE: It will bring your joy to others!
Giveaway at 10k!

Пікірлер: 32

@EvendimataE 2 ай бұрын

ILL MAKE THIS ALL CAPS, ITS IMPORTANT......THE KEY POINT IS "RUBBER BOOT INSTALLED ON THE ENGINE 1ST. THE BOOTS HAVE THAT SLANTED CUT TO GUIDE THE CARBS....IF YOU WILL INTALL THE BOOT TO THE CARB 1ST, YOU MIGHT END UP RUINING THE BOOT.....AND OF COURSE DONT FORGET TO LUBE.

@frankb4292 Жыл бұрын

Best video I seen on installing Magna carbs for years 1994-2003. No bloviating or annoying music.

@MannyMarvelous Жыл бұрын

exactly what I was going for

@davidblack7528 9 ай бұрын

Great job and so needed video! Bought my yellow Magna new in 1996. The Honda dealer charged me $500.00 two years ago and I know it's gone up if I do it again. I will do it myself next time. Thank you Manny

@delschier1419 9 ай бұрын

You put the float bowls on backwards. The float drain needles are supposed to be on the outside so you can get to them when the carburetors are on the bike!

@unique-daann6098 Жыл бұрын

My carbs haven’t been cleaned for 5-6 years now. And she still rips like a silver back ape. (Almost riding season near me) but next fall she’s getting rebuilt.

@MannyMarvelous Жыл бұрын

surprisingly easy job

@dannysmits9706 Жыл бұрын

Would that be because there is real petrol available in every of your country's gas station?

@SeriousGamerTouch 2 жыл бұрын

great video, glab you got it running, now i have to go do the same job lol.

@MannyMarvelous 2 жыл бұрын

it's easy to do and worth it

@1Somsak Жыл бұрын

@ 4:35 you mention how "people complain how hard it is ..." . There's a HUGE difference re-installing carbs on a 3rd gen. bike (like yours) and a 1st gen. bike. The carb bank angle is more pronounced on the 1st gen. bikes making the alignment and fit a lot more difficult. The 3rd gen. alignment is almost straight on compared to the 1st gen's. Maybe that's what folks are complaining about.?.?.?

@MannyMarvelous Жыл бұрын

that's a good point! I'm familiar with that fact but the way to get it on is still the same. what I'm really trying to say is that complaining isn't going to make it any better but finding ways to have machines work for you instead of against you will always prevail.

@vicjames2743 9 ай бұрын

I got charged $1200 for motorcycle shop to rebuild my 94 magna carbs. They put plastic zip ties on each tube connection

@MannyMarvelous 9 ай бұрын

now that's just shameful of them. damn

@BloodSteed 2 ай бұрын

Look up the Carb Spa, ran by MagnAndy, a trusted member on the v4musclebike forums.

@MannyMarvelous 2 жыл бұрын

FIRST!

@joshhinton4232 Жыл бұрын

what shocks are those on your bike?

@alexanderking3971 Жыл бұрын

Can you do a vid on bench synching these carbs? I bought mine last season. It needed a lot of TLC. I've redone all fluids, new steel brake lines. Lithium battery. Everything except the carbs. They scares me 😂

@MannyMarvelous Жыл бұрын

I'm pretty sure there's a section in my video about how to bench sync. but if not here's the trick. it's super easy. as long as the jets are already set- all you need to do is adjust the 1 screw on each butterfly valve so that the little time hole on the wall of the intake that meets the butterfly valve is barley visible when the valves are closed. do this to each one then you can adjust idle from there while running. you'll need to take the unit off first.

@alexanderking3971 Жыл бұрын

@@MannyMarvelous awesome I'll give this a try

@isaacthompson7117 Жыл бұрын

Hey can you show a video on how to rebuild the carburetors?

@MannyMarvelous Жыл бұрын

if the need arises I will!

@inajefflymanner 11 ай бұрын

I have a '94 magna VF750. The carbs were leaking fuel so I took it to a shop for a rebuild. Mind you I had to remove the carb myself and bring in just that. Not a big deal, but I am very new to riding so my problem may be my own fault. Anyway, got the carb back, put the bike back together and now it won't start. :( It turns over, but just won't start. Not sure if it's something I did in the installation or if it means the rebuild was bad or what. Any ideas?

@MannyMarvelous 11 ай бұрын

they have a vacuum automatic fuel shut off so it's nothing that you did wrong in the first place. in fact leaking carbs is a sign of having the same exact issue that I had in this video where the float needle had no more gasket left. as for the no start it could be a multitude of things but the simplest thing is that maybe it's jetted wrong or you forgot to turn on the fuel once you put the carbs back on from your petcock

@AlexeyShkalyabin 2 жыл бұрын

Congrats, bro! Did you use the same old gaskets with sealant?

@MannyMarvelous 2 жыл бұрын

nope they were in the new rebuild kit!

@abiprates284 Жыл бұрын

Great video. I just got a 1988 Honda super magna 750. Would carburetor be same? Did you have to synchronize yours? thank you.

@MannyMarvelous Жыл бұрын

you can bench synch them by looking at the butterfly valves in comparison to the little holes in the side of the inlet. just make sure they're all same