2007 ODYSSEY: Called the dealer $312.30 for labor (2.5 hours they say) + $91.96 for a faulty part. Total = $437 Bought the part at Advanced Auto, installed & test drove in 1.5 hours. Total $47. Great video. Thank you!

We just saved ourselves 1260.00 thanks to your help and videos 🙌

Messing with the steering column had its moments, but I was able to replace the switch in about an hour, saving about $400. Thanks for the video! Recommend an angled phillips screwdriver for that one pesky screw. Very straightforward replacement.

This job took me a good 2 hours on an 07. I’ve been working on cars for 50 years for some perspective. What I found was that the two outer screws holding the lower cover on, as well as the two screws holding the switch on, are JIS, not Phillips, and it helped to have both a #1 Phillips screwdriver and a 1/4” bit in #1 Phillips, both with the very tip ground off. That simulated a JIS driver closely enough. I also used a pair of right angle ratcheting bit holders, straight and angled, and those were very helpful. Overall it was kind of a PITA job. But great video!

Pro Tip: Turn the steering wheel upside down and pull out the bottom kick panel off a bit (don't need to take all the way off). This will allow you to remove the bottom steering column cover easier. Also, if you don't have a right angle screwdriver, you can use a philips bit and small vice grips.

Changed it myself. Very proud. Broke down other stuff though. Probably not that important

Please add link to the part I’m having a hard time finding the part you used

This was not for removing the ignition tumbler and replacing it? I need to replace the old tumbler with my new one that I had a locksmith match the keys to the old ones so I could get into the doors and start it with same keys. Had him program me 2 new ones also.

I have a2006 and unable to remove lower cover after removal of the three screws. what year is this odyessy? any advise would be appreciated

I took everything apart. It wasn't a problem since i previously changed the ignition lock cylinder a year earlier. This time, when i disconnected everything for the ignition starter switch. I turned the key before i had the starter switch in and now i can't turn the key again. I might just the take lock cylinder off again and see whats up if i can't find an easy fix for it.

I got a 2011 odyssey. Is there something I’m missing getting the trim casing off the steering column. I can’t find any info on a 2011. I get it halfway but will not budge.

Is it possible to swap an ignition switch solenoid off a used and out it on my current one to avoid all this? My key gets stuck in first position regularly. Thanks man

How did you get the lower housing off? The steering wheel height lever is in the way. The video cuts off there.

Nice video K. I like the edition and the yext as a reference. I wondered if you can show me how change a flat tire. Thank you and I wait for more of your videos.

when you change the ignition do you have to program the new keys?

hey man i did what you did exactly in this video but now my key will not turn at all and i put the old ignition switch back in and still won’t turn and then accidentally locked the steering wheel. any tips on what i should do

Do we need to reprogram or not for odyssey 2009 after replace it? Thanks

uable to remove lower shroud to access ignition switch. our is a 2006 model. the lever is in the way.

I have 01 Honda odessey it just star stall when drive this week but it turn an crank but if wait for few min an shake the key it start up an run HELP PLEASE

My wife has an 07 odessey touring the parking lights and tail light stay on and kills the battery would this fix the issue?

2005 odyssey key won’t turn car over smashed key what can I do? If I replace ignition can I get a different key?

My van died while driving. After checking the alternator, battery and fuel pump everything seems good. I'm guessing it's an ignition switch issue, I have an 07 odyssey. I hear it's a common problem. What do you think? It turns over but never starts.

The key won't go all the way in on my wife's Honda Odyssey.. and it won't turn over. I feel like I can replace this myself but I've heard you may have to have the dealership problem the key? Is this tru? I don't have a scanner or anything to program it myself

So I was able to take the wafer out I put it back together and now it won’t start

So if the key doesn't turn do I have to replace that part?

You cut out steps in the video, if you are going to do a how to video it should show the whole process, we couldn't get the bottom part off and you cut that part in the video it would have been helpful to see that even if it took you as long as it took us to get it out.

I broke my tilt lever trying to tske out bottom piece 😮 im calling the locksmith he can deal with it. These oddesseys suck