I had trouble with my machine and found you. Thank you so much. I fixed it with your video. Thank you. I have a small tailoring shop, and you saved my day.

I watched this 3x and managed to set the timer on my JUKI TL98Q. It "broke", needle locked, I panicked because I had a quilt to complete and a deadline to meet! Repair folks booked for months so I searched for help and found your instructions; THANK YOU!!!! 👏

Your technician clearly explained the steps, fantastic. I have a BROTHER DB2-B797 and your video allowed me to fix the timing myself. Thankyou 🙏 From Australia 🦘

Thank you so much for the detailed timing tutorial. I live 2 hours away from the nearest sewing repair person. So, I’m grateful for this video.

This video saved my day today - the manual wasn't helping (and didn't explain this method at all) so thank you so much!

Thank you so much for this video. I didn’t even know my timing was messed up I just thought I had cheap thread or my needle was too small. So I purchased new thread and new needles in my thread just kept shredding and then I came across this wonderful video. Followed every step and now my problem is gone. 😊 I’m a happy camper!

Thank you so much, as a woman & not knowing anything about fixing my machines but through this video I managed to set my timing 🎉🎉🎉saved a lot of money

I was struggling for the past couples months and this video helped me FINALLY get my machine sewing smoothly. Thank you!

So thankful for this video! I broke a piece off the basket trying to remove a thread jam. So once I got my new part and put it back together, I realized the timing was off, and with the help of this video, I was able to time it myself. Again, thank you so much! ☺

Your tutorial saved me. I spent the whole day trying to set the timing and it just was not working till I came across your tutorial. THANK YOU

All these years I never knew there is a timing mark on the needle bar. Great explanation.

I am in absolute awe of the beautiful detail and focus of this video. You are both wonderful instructors. Thank you

great video! my Juki DU-141 was eating needles so i pulled the rotary hook and found it was seized... upon trying to un-seize it i broke it right where the position finger goes... so i bought a new rotary hook and watched your video for proper setup... man, straight forward and down to earth... my foot was loose too and your video helped me figure out how to align it and now my Juki DU-141 sews like a dream! thank you for your taking the time to make this video!

After watching like 5 times I understood the importance of the two marks on the needle clamp and i managed to solve the issue of timing on my machine. Thank you soo much 🙏🙏

Thank you SO MUCH for this video! It was super helpful. I had some thread break and get caught under the feed dogs and that ended up messing with the hook timing too, with your help I was able to remove the plate and feed dogs to remove the thread, and then fix the hook timing and re-assemble everything perfectly. Edited to add: and y'all seem like such nice people, I felt like there was some good banter in there too so it was a pleasant video to watch.

Thank you so much, I couldn't find anyone to fix my machine. I followed the instructions and I did it . This is so great, good job!

Excellent video. My mom's machine has been sitting idle for 5 years. An old ddl 555. Broke a needle due to not inserting the bobbin housing till it latchedand before I know it checking out related videos. Now understand the bobbin side much better. And was threading the wrong way too.

Thanks for excellent explanation and close up video! Knocked the timing off and was able to fix quick and not put me behind at my tailor shop.

Thank you for putting this video up my wife was having problems with the bobbin thanks to you I was able to fix the problem.

Thank you so much😍!!!! Its a great tutorial. Was able to reset my timing in less than 30 mins. I was panicking its had been raining for more than 24 hrs and the repair person couldnt come yet I had an urgent order to finish

So thankful for this video!

I can't say thank you enough 🙏 this video have saved me soo much money thank you again

Hi I just want to thank you for this information it has helped me so much it cost me so much money for someone to come to my house to repair my machine something I can do for myself ❤❤

Thank you for the detailed video. Trying to fix the timing on mine as thread got jammed in there and haven’t been able to use it since I bought it new a few months ago so I’ll give it a go with your instructions.

You guys just saved me. Thanks A lot!!

Ty for video, learn another. New to sewing machines.

This is a really good video, very detail and attention to every aspect. Really appreciate it so much. Thank you for taking the time to explain this in full detail with much explanations.

Thank you for this wonderful tutorial 🥰

Thank you so much Sir’s this was really help❤❤❤

THANK You! This video is a lifesaver!!!❤

This video is a life saver. Thank you so much

This video saved my hair on head. Thanks dude 👍

Incredibly helpful! Thank you

This video saved me alot it really help I'm so greatful 😊

I have a Juki TL 98Q and there's so much more stuff in the way of the basket. I haven't been able to find any videos on how to get in there unfortunately. If you ever have a chance to make a video on that machine, it would make my year

Thank you so much ☺️ Good teacher thank you for saving me I have so much clothes to sew

Thanks for all teaching God bless you

Keith, thanks for sharing

Thank you so much🙏🏽🙏🏽you just saved me from the stress I was going through 🙏🏽🙏🏽

So thankful for this video

Thank you so much u saved my life as i depend on my sewing maching for my daily bread

Thank you so much for this information. God bless you.😊

Thanks for your valuable video.

Thank you for valuable information

Thank you this content was very helpful!!!

Thank you!! Great instructions and video. So appreciative!

fantastic video!

Thank you so much that was really helpful

Multumesc frumos am reusit cu ajutorul Domnului si al dumneavoastra sa imi repar masina salutari din Romania

Thank you so so so so much for this. THAAANNNKK YYYOOOUU!!!🎉

Thank you alot it was very useful video

Thanks very much !I got it!

Life saver

Awesome and so helpful, thank you

Cool ,, thank you for sharing.

Brilliant! Thank you!!

Great video!!!

Thank you! I did it!!

Thank you so much!

thanks for great info I've the same sewing machine, it will be usefull if it need to do it by myself. thanks so much.

i can't get any of the screw off. they are so tight !

This is the best how to I have seen ,I was wondering though what the other marks are for ? ,I have a 555dl that I really struggle with

Great and detailed! But I got a question. Or at least something like that. I am sewing neoprene with nylon thread, the normal timing didn't work, so I change it a bit, the needle goes a bit further down the bottom marks and I synchronize it with the going up usual mark. This is to give more gap to make the thread hoop down the fabric.... This works, I managed to do the stiching without loosing any. The question would be if this is good for the Machine or I'm doing stupid changes... Those 2 materials together are a nightmare, maybe I am not using the right needle (DB 12-80)... Thankyou for the advice

Hi guys, thanks for the video. I have a question, what would cause the machine to skip a few (in the first 10cm) stitches at the beginning of a garment. I have tried different needles, fabrics and threads etc. Always the first few cm of sewing. Any help would be gratefully appreciated. Thanks

Thank you so much for this! Do you guys have, or could you make a video on replacing the knives in a DDL8700 with an automatic thread trimmer assembly?

So, if I use another needle but a 90/14 I'll have to retime it? The manual is wrong unless it means "capable" of 9/65-18/110" but as the needles get thicker will they start to rub on hook? Or is the ditch on that side of the needle keep it at the same spot no matter what size? Makes sense after seeing this that thicker needles may rub that hook. If that's true then the manual should say that. They make it sound like you can throw anything from a 9/65-18/110 needle in as long as dbx1 or whatever it it I also know that above that size the dbx1 needle shank is 2mm instead of 1.68mm or whatever. So maybe that's what they mean is the needle bar can take those sizes and with adjustments can be set for different sizes. But man that would slow you down having to go from 90-110 for denim and having to do this every time lol I'll be calling today with a few questions and possibly ordering one of these

I need more samples so I can try to fix mine

Thanks for the video. I accidentally put a scissor underneath the needle and when i switched the machine on, the needle hit the scissor and broke. Now my machine can't sew. What might be the reason? Was needle holder affected 😢

Is the hook timing the issue for the needle skipping stiches on bulky parts of the fabric?

Hi, do you have any similar videos but for the juki LZ 271? Thanks

Hi, what should I do if my machine (juki ddl 8700) doesn't have them 2 lines...my machine won't sew any stitches into the fabric top or bottom

Watched this 6 million times still have no clue what is going on …

Do you have this same video for the 1541s? Can't seem to find one. thanks.

So why are new Juki machines not shipped to Nigeria, since they have their largest African consumers in Nigeria?

The bar underneath that’s holding the bobbin stuff together is blocking my bobbin from going around (I’m sorry it’s SUPER late and been trying to fix it for 3+ hours so all technical term has left me). Any tips from anyone to help me would be GREATLY appreciated 😭

المكينة حقي نفس ذي لي فديوه لي اسبوع من، يوم مااشتريتها. بس تكسر الابر وصل مش عارف من ايش تكسر. وايش المشكله

Hello! I bought a used juki machine but am afraid it might be too busted for me to use. It is hard to crank the hand wheel and I don't know why. I have oil but didn't put it in yet, because I wanted more guidance on what to do. Any advice or help is greatly appreciated 🙏

What should i do when my bobbin thread is always tearing

I am having trouble with my machine JUKI DDL-8700, it just keeps running by itself, please can I do

Do you fix brother sewing machine

I tried replicating this, I’m now able to pick up my bobbin thread to start sewing. But when I try to sew it’s still not picking up the thread after the first stitch. Any tips?

My Juki won't even power on it died while sewing and now won't power on. Can you help any suggestions?

Why would the timing be off?

Bobbin case, not basket

How does a machine get out of time? Seems like it is not a wear item.

Marathi me

My email machine is jumping 8500