Hornady Lock-N-Load AP Unboxing and Setup
Рет қаралды 209,308
8 жыл бұрынPlease consider supporting Ultimate Reloader on Patreon: / ultimatereloader
-------------------------------------------
Important: See disclaimer at end of video description.
-------------------------------------------
Full story: bit.ly/22Um8w7
Wondering about the Hornady Lock-N-Load AP? In this video I show you the entire unboxing process, a review of press and parts, mounting and assembling the press. You'll see everything needed to get your press to load ammunition except die and shellplate installation.
*Update: In addition to the steps listed, you'll need to drop on the primer pickup tube, screw on the shield tube, and then snap the plastic top cap in place to finish priming system assembly. I'll show that in the next video. Thanks alzathoth for pointing this out!
More related blog posts and videos: ultimatereloader.com/hornady
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Disclaimer:
You alone are responsible for the safety of yourself and your property.
Check local and state laws before undertaking any activity involving possessing, transporting, and shooting firearms. Check local and state laws before attempting to load ammunition or perform any modifications to a firearm. Always abide by the law. Always practice gun safety.
The content on this channel (including videos, ammunition reloading data, technical data, comments, and any other information contained within) is for demonstration purposes only.
Do not attempt any of the processes or procedures shown or described in this video or on this KZfaq channel (gavintoobe).
Any reloading data supplied on this KZfaq channel (gavintoobe) or in this video, including any comments from viewers and readers must be assumed to be in error.
Always consult at least three sources of manufacturer's ammunition reloading data before reloading your own ammunition.
Do not attempt to repair or modify any firearms based on information found on this KZfaq channel or in this video.
Gunsmithing procedures should only be performed only by a licensed gunsmith.
Ultimate Reloader, LLC can not be held liable for any harm caused to any individual or any personal property related to activities, procedures, techniques, or practices described in whole or part on this KZfaq channel (gavintoobe) or in this video.
By watching this video in whole or in part, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this KZfaq channel (gavintoobe) or in this video
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Material Connection Notice:
The following Ultimate Reloader partners are featured in this video:
- Hornady
Ultimate Reloader partnerships involve one or more of the following:
Product supplied for evaluation + testing + features in videos/articles, paid advertising and promotions, engineering and product development services, scientific testing and evaluation, external media production and related marketing services.
Ultimate Reloader LLC is committed to publishing subjective and data-driven information+insights related to products whether it be favorable or unfavorable or both.
For more information about Ultimate Reloader partnerships, please visit: ultimatereloader.com/about
@mikescribner5537 8 жыл бұрын
Thanks in advance for your video series on the Hornady LnL AP. One thing that Hornady recommends is, cleaning all components ie: rifle and pistol rotors, powder measure, etc. before using them. All your video series are very informative. I thoroughly enjoy my AP press. I load 45acp, 357, and 556 on the press. I use my Hornady Single Stage for all my large rifle cartridges. Thanks for all you do.
@scottgentile1663 3 жыл бұрын
Thank you for making this video. You just made setup a breeze instead of a headache.
@mrhangfire1 8 жыл бұрын
Pretty good press, I have been using one for close to 5 years now. I probably get a little heavy handed when it comes to priming and I have broken the main toggle link that the handle threads into(Hornady replaced it for free, no questions). There is also a good sized divot in the aluminum frame where contact occurs with the priming punch. My fix for that has been to tap a used small primer cup into the divot with a small brass hammer. The case feeder is a life saver and I like the roller handle I bought from Inline Fabrication. The press is pretty low maintenance, the base plate will work loose over time but two Allen screws tighten right up.
@ericd385 8 жыл бұрын
very cool, and couldn't come at a better time. i have a L. N. L. AP coming! finally upgrading from the lee pro1000 that has served me since 2005
@seemeeseeu 3 жыл бұрын
New to the progressive press scene-been a single stage loader for over 10 years. I appreciate this video as an overview and primer to loading. I found this system(even with gouging going on...) to bee about half as expensive as the blue presses for caliber changes. Although I have zero experience with either the red or blue presses(been on the green ones)-I am already impressed by the package and Hornady's customer service. I wasn't going to wait for 4 months for a Dillon, although will probably buy after the stupidness (if it ever does?). I am happy with Hornady so far and can't wait to load alot. I would recommend the mr bulletfeeder and a case feeder(there are 3d printed versions now). Thanks Gavin !!!
@sdlillystone Жыл бұрын
Top tip = get large boxes and keep pistol dies wiith pistol powder etc Same for rufle dies etc. COMPLETELY clear loading table including cleaning out powder dispenser before moving to another calibre NEVER PUT PISTOL POWDER IN RIDLE CARTRIDGES.
@georgelopez7316 8 жыл бұрын
Great video Gavin. I have the same press and have loaded thousands of round of both pistol and rifle. Once it is set up the key is getting the indexing correct. On my press the indexing was a hair off and drove me crazy. You have to make really small paw adjustments to get it correct. Another key to smooth running is keep the press clean. If even a small amount of powder or dirt gets under the shell plate, primer feed etc. it can cause problems such as indexing improperly or primers not seating correctly. I believe overall it's a great press and I believe all presses have their nuisances.
@jasonpitchios9243 8 жыл бұрын
Just Bought this press. Thanks for the useful information, keep it coming!
@Ultimatereloader 8 жыл бұрын
Sweet- are you cranking rounds yet? :)
@davidarringtonmd 8 жыл бұрын
+1 for Steve's comment below. I'm getting ready to start reloading and have been researching the best bench setups to use. I think yours is by far the best design I've seen. A brief video of how you made it and what it would take to replicate it would be awesome. Keep it up with all your great content!
@Ultimatereloader 8 жыл бұрын
+David Arrington Thanks David!
@Twoboxer2 8 жыл бұрын
Adjusting the pawls can be confusing enough. But it is often made more difficult because most shellplates come with their ball bearings protruding too far out. So when the shellplate approaches the correct position, the ball bearings grab their detent holes in the subplate. This causes the shellplate to lurch forward. That creates more confusion (did the pawls or the ball bearings finalize the index?) and causes powder to pop out of small as well as nearly full cases. Tap the ball bearings further into the subplate (eg with a brass punch)so that the shellplate settles *quietly* into position. Now you know whether pawls need adjusting, and powder popping is eliminated. If you tap the ball bearings in too far, turn the shellplate over and tap them back out :)
@esman1357 7 жыл бұрын
Hornady instructions direct users to clean anti-rust coating from the powder drop before use
@iamkikoman 7 жыл бұрын
Great Video. This has helped me decide which press to buy. I have decided to learn reloading for two reasons: 1) try to bring down cost for ammo, 2) I live in California and the new laws will prevent me from buying ammo online. I figure I will buy all the components (brass, bullets, primers, etc.) online and make my own.
@barlowjmb 2 жыл бұрын
Have you moved yet? Or are you still in California ?
@eXdXgXe4life 8 жыл бұрын
I own the same press and love it. It does have its issues though. Some times primers jam up, getting it indexed correctly can be a problem, and changing it the primer bolt thing on the underside can be a pain. Minor complaints compared to the thousands of rounds I've loaded up.
@enam100 7 жыл бұрын
Great instructional video. Thank you so much.
@Ultimatereloader 7 жыл бұрын
You are welcome, thanks for watching!
@MTNcorps 4 жыл бұрын
I just got this setup in hopes of learning. The kit now has a spent primer catch can.
@ronaldlabiche8777 8 жыл бұрын
great videos so far But I would like to know if Hornady has a low powder buzzer alarm like Dillon has for their presses
@exeninfogmailcom 8 жыл бұрын
Thanks for this Video. Do you have also made one for setting up the PTX expander bracket? The original Hornady Video is not so satisfying.
@jarekcieslik7544 7 жыл бұрын
Great video - thanks for sharing
@georgegiambelluca4812 3 жыл бұрын
Great video, do you know if I can use my Lee dies with this system. Thanks Gavin.
@jormen23 4 жыл бұрын
Hey Gavin, can you use lock n load to size cast bullets?, thanks
@jiujitsu2000 8 жыл бұрын
great video brotha! thank you for sharing!!
@Ultimatereloader 8 жыл бұрын
+jiujitsu2000 Glad you liked it!
@bradprather6749 3 жыл бұрын
Great video. I'm brand new to loading. Can I buy complete die kits, or are they all separate parts. Example 9m kit, 223 kit, etc.
@paulflores5499 6 жыл бұрын
OMG THE NIGHTMARES,,,, I haven't seen a "bloody mary knife" since the last carpet install job I was on,,,,over 27 years ago,,, used one of those for many years. Cool vid , thanks for the info
@Ultimatereloader 6 жыл бұрын
They are scary aren't they? (carpet knives)
@RyanHoulio 8 жыл бұрын
I use AP unit (case&bullet feeder) to load 9mm and am finding my OAL to be wildly inconsistent. quick research online shows i'm not the only one. Not sure how much you are going to like loading 6.5 in the press.
@tetfemal03 8 жыл бұрын
do you clean your dies and powder measure before setting them up?
@MagnumMike44 3 жыл бұрын
Whether your reloading components have Hornady, RCBS, Dillon, or any other American-made brand, you can't go wrong. That's why you'll see a mix of brands on my reloading bench, including Hornady bullets.
@mnPatriot 4 жыл бұрын
I have this same system. We can load .38 and .357 all day, no issues. However, the 9mm will not seat the bullet at the correct depth. It's either too deep, or too tall. Any suggestions? Thanks!
@TehBr0 8 жыл бұрын
Great press, I have 2 of them!
@jfdpratt 5 жыл бұрын
Did you make the mounting plate yourself, or is there somewhere you can get those? I just built a bench, and I have some spare track I could drop in there to use something similar to yours. Thanks.
@CrushOfSiel 3 жыл бұрын
So if I get this same package and I want to lead 223. Is the proper shell plate the only other thing I need? I have all the equipment to run a single-stage press as that is what I've been reloading with for the last year.
@johncarr123 4 жыл бұрын
Is this unit better than the Lee progressive loader when it comes to primer insert?
@seandobson6221 3 жыл бұрын
How do I know which powder insert I need?
@harleyhobie3115 Жыл бұрын
I've been loading multiple pistol calibers on my lnl progressive for years. started to load 223 with it and noticed a issue don't know if its just my press but if I try sizing on the progressive I can't get it headspaced to where I can on my single stage press. when I try it either is very difficult to bring down or the case gets stuck in die. wondered if you had any thoughts on what's happening? for now I'm depriming sizing on single stage. thanks
@therockindoc5453 5 жыл бұрын
very HELPFUL!! Thanks very very much.
@Ultimatereloader 5 жыл бұрын
You are welcome!
@steelbucks1202 Жыл бұрын
What kind of table/workbench is that? It looks amazing
@55Warbird 3 жыл бұрын
what is the purpose of your "riser blocks?" Thanks. Great video.
@rogermays3136 3 жыл бұрын
How wide does the table need to be adding feeder
@publiogidoni5724 4 жыл бұрын
Will this do 300 winmag and 338 lupua i know it won't do 50bmg
@dennismott4226 6 жыл бұрын
Where do you get that neat mounting system?
@johnschlich5505 8 жыл бұрын
where is the plans for building that table
@esteemedenergy 7 жыл бұрын
great job buddy
@Ultimatereloader 7 жыл бұрын
Thanks dude!
@padywac1970 2 жыл бұрын
I’m tired of the frustration of my Lee progressive press. I’m hoping this one will be less frustrating.
@Yourmomisbomb007 6 жыл бұрын
I just used super glue. Squirted it all over the bottom of the press. Set it down on my bathroom sink. Now I reload while pooping. No down time!
@jeffcallaway3557 3 жыл бұрын
I like that,could get highly flammable!!🤪🤪🤪🤪
@paulchristen7610 3 жыл бұрын
huh, no shit?
@RafaelHernandez-tk2xh 7 жыл бұрын
what was the price on the setup?
@willy03wh 4 жыл бұрын
So basically you need to get the bottom plate and dies?
@christopherschreiber5963 7 жыл бұрын
What no scale, mic, or nice tin sign comes with more expensive set up?
@henrybucki7813 3 жыл бұрын
i think my pro 7 died ,hornady no longer had parts ,so they sent me a new lock and load ap .i think it was $200 what a deal they also paid shipping
@chuckswayzee 4 жыл бұрын
aren't you supposed to clean some of these parts according to Hornady?
@77grainballistics66 3 жыл бұрын
no reloading manual???
@BlaineNay 8 жыл бұрын
I once had a Hornady Lock-N-Load AP. I could never trust it to prime the cases. Never. I frequently had to disassemble the press to clean out the powder that kept sifting out of the empty primer pockets. I spent considerable time on the phone talking to Hornady's tech support and even they couldn't hep me to get it to work correctly.
@albatro2676 7 жыл бұрын
Thank very much for all the information. I am going to visit the US on next March, and I am deciding what brand of the different progressive press i am going to buy. I am between this one and the Dillon XL 650... Hard decision...
@donl5158 2 жыл бұрын
New to reloading. Purchased the Hornady AP, scale, clipers etc. Loading 30-30, 357, and 9. What are your guiding directions for the newbie. Any services available where you can buy an hour or two of time to properly load with the Skillmaster's tips. Thanks
@sdlillystone Жыл бұрын
😢
@alzathoth 8 жыл бұрын
hey Gavin. you didn't show how to assemble the primer system...? did I miss something here? ;)
@Ultimatereloader 8 жыл бұрын
+alzathoth You are correct! updated video: *Update: In addition to the steps listed, you'll need to drop on the primer pickup tube, screw on the shield tube, and then snap the plastic top cap in place to finish priming system assembly. I'll show that in the next video. Thanks alzathoth for pointing this out!
@billfrankwurtz 8 жыл бұрын
Gavin, is this a refresh from three years ago? Did you get rid of your original and are now going through a newly purchased one?
@Ultimatereloader 8 жыл бұрын
+Bill Wurtz Bill- I still have the Lock-N-Load AP press that I've shown in the videos previously. I decided it was time to show unboxing (I haven't shown that for this press yet) and wanted to refresh the content with my latest tools (4K camera, overhead camera, etc).
@toolman9081 9 ай бұрын
Is this a good set up to buy in 2023?
@toycollector2611 7 жыл бұрын
Did you clean all the parts to remove the packing grease?
@Ultimatereloader 7 жыл бұрын
Only certain parts - some of the Hornady LNL AP parts are somewhat prone to rust, so it's actually a good idea to spray down lightly with WD-40 or similar, wipe excess off with rag to prevent corrosion/rust - completed cartridge bin bracket, metering inserts (not internal), and other small parts.
@thegungroup2818 3 жыл бұрын
Where is the Primer Slide Spring....AND....where is the large Primer Slide?? I didn't get ether of these in my box nor the spare plastic top Primer Arm.....:(((
@cal30m1 7 жыл бұрын
I would recommend degreasing the internals of the powder measurer and applying a coat of dry lube to the internals.
@Ultimatereloader 7 жыл бұрын
Yes, good call! + Hornady One-Shot to the outside of steel parts- completed cartridge bin bracket, etc.
@CaveWyatt 6 жыл бұрын
Ok, gotcha. I asked this question about the powder measure before I found this comment. Now I'll go ahead and clean it up if I can find some One Shot at Bass Pro or somewhere nearby. Thanks!
@ryanmoore7098 3 жыл бұрын
What was the MSRP price for this originally? Now its going for $1500!!!
@jmf1976jmf 2 жыл бұрын
Under $500
@danielsherman2503 7 жыл бұрын
Have you had any issues with inconsistency in loads with the powder measure? I'm new to reloading and I want to reload 6.5 creedmoor but also 9mm and 223. Thanks
@Ultimatereloader 7 жыл бұрын
This is the most consistent powder measure I've used- two reasons: drum-type (best for precision), and includes baffle to make powder packing consistent from full to empty!
@jozy5154 6 жыл бұрын
Is this hornady lock n load press worth buying?
@Ultimatereloader 6 жыл бұрын
It is a GREAT press- what are you planning to do? (Lock-N-Load AP is optimised for frequent caliber changeovers, ...). Context on your loading will help me give you an answer. :)
@jozy5154 6 жыл бұрын
gavintoobe just want to load .357 magnum, 45acp,
@Ultimatereloader 6 жыл бұрын
It would be perfect for that!
@jcdo367 7 жыл бұрын
can I use Lee dies? tks.
@ZERO_42069 7 жыл бұрын
J Cury yea with the LNL busings
@jcdo367 7 жыл бұрын
Tks for your time bud!
@BecksArmory 8 жыл бұрын
I'm sure you've been asked this a million times but... What is your favorite press?
@SabreWolferos 8 жыл бұрын
+richarddbeck I would like to know as well
@SeanMcKim 5 жыл бұрын
RIP.
@charlesmoeller8826 7 жыл бұрын
Who has money for such an elaborate mounting system? And were did this mounting track and plate come from? I know it was not included within the AP box.
@Ultimatereloader 7 жыл бұрын
It's not included. :)
@danieldiporto9818 6 жыл бұрын
Hi i've buyed this press one week ago but i need to know if insedi the box the powder funnel i only for rifle cartridge o also for pistol. how i can understand it? i need for reloading 9mm thanks
@Ultimatereloader 6 жыл бұрын
I would contact Hornady - you should have the correct powder funnel (the long one) for 9mm!
@abee.s.corpus2455 6 жыл бұрын
Gavin told you right. Another option is to buy a Hornady PTX (powder through expander). It goes in the powder measure assembly in place of the standard spacer/drop tube. It expands the case mouth, freeing up a station that would otherwise hold an expander die.
@ZERO_42069 7 жыл бұрын
what bench is that?
@Ultimatereloader 7 жыл бұрын
It's a custom bench, I plan to offer a kit to "build your own" !
@ZERO_42069 7 жыл бұрын
gavintoobe cant wait fot it, my bench is a shitty home made one from scrap lol
@HDtenor1 5 жыл бұрын
Does how he says measure drive anyone else nuts? 🤣
@EdboxEddie 4 жыл бұрын
powder major :P
@WeencieRants 3 жыл бұрын
Maaayzer
@mafirearmsafety 4 жыл бұрын
You forgot to mention buying shell plates, so actually you are Not ready to go...
@iamcondescending 3 жыл бұрын
So you don't even get the case tray with the press? That's dumb.
@galamonkey 4 жыл бұрын
“And I could hypothetically mount 8 presses to the bench, which I actually have done before” *smirks* *every woman’s panties hit the floor at the same time, causing a 6.7 richter earthquake*
@saddleridgearmory4675 7 жыл бұрын
Defiantly De-grease all of the parts.
@Ultimatereloader 7 жыл бұрын
I only de-grease the parts that need it. (under shellplate powder-contacing parts etc.) - why? Some hornady parts are bare steel and therefore susceptible to corrosion. In fact, it's a good idea to spray such parts with a product like WD-40 or Ballistol and wipe off the excess (except the parts I mentioned).
@HaqqAttak 7 жыл бұрын
It says on their set up video that you MUST degrease the powder measure.
@saddleridgearmory4675 7 жыл бұрын
I degreased the powder measure and the plastic permanently fogged/stained up LOL.
@CaveWyatt 6 жыл бұрын
Great video! Thanks! I was wondering the same thing about the powder feed. Hornady makes such a big deal about removing the corrosion guard, even showing how to disassemble the measure to clean it up. Just a ploy to sell us more Hot Shot (or whatever it's called)? I found an AP under our tree this morning and would like to be sure the powder doesn't clump up or something. Thanks!
@Steve-iw1kj 3 жыл бұрын
I sold that press I totally hated it it was the biggest piece of crap I have ever tried to use....I'm sticking to dillion
@Randy_84 3 жыл бұрын
Not true, you'll need a new plate for whatever you're loading.
@Ultimatereloader 3 жыл бұрын
Actually no. For example: 40 S&W and 10mm use the same plate. 308 Win, 6.5 Creedmoor, 6mm Creedmoor, 243 Win, 6 dasher all use the same plate.
@Randy_84 3 жыл бұрын
@@Ultimatereloader when I got mine, I couldn't reload 338 Lapua or 375 gov 🤷♂️
@Ultimatereloader 3 жыл бұрын
@@Randy_84 Correct- 30-06 is about the longest cartridge the Lock-N-Load AP was designed for :)
@blankreg9890 6 жыл бұрын
"May-sure..."
@Ultimatereloader 6 жыл бұрын
That's how we say it here on the West coast! :) :)
@memoriespast1499 3 жыл бұрын
I followed and I have like hundreds of other parts not installed... not a thorough video
@FJBAFYFVFH 8 ай бұрын
No powder thrower no case feeder no bullet feeder. Boring!
@grcunyus 8 жыл бұрын
this video is a waste of time. too much time spent on the packaging. nothing about setting up the powder measure on a cartridge, or setting up the primer system. I want my 15 minutes back.
Hornady Manufacturing
Рет қаралды 336 М.
Bolt Action Reloading
Рет қаралды 106 М.
HornadyLoader
Рет қаралды 28 М.