Thank you. I've been driving my prius since 2013 and it has always had crappy steering and handling because it was never calibrated after getting new wheel bearings, brakes, etc, so the steering has always been all over the place and it was actually very annoying and frustrating to drive. After finding out about your video, i decided to try this and man, what a big difference! My steering is a lot more stable and isnt all over the place anymore. Even my braking got smoother. I never thought my prius would drive like a normal var again. Sir, i just want to say hats off to you for sharing this video. I am now happy driving my prius again, and i dont plan on selling it anymore. Thank you. Thank you. Thank you!

You just saved the day my friend. Thanks 🙏🏿.

Prius zvw30 2010. Erratic steering. Alignment done. Still not great. Steering jumpy on straight roads at speed. Body roll at corners. No feeling in the wheel. I used your method. NOW car is driving fantastic! My wife is happy with this car for the first time in 2 years. Thank you for your upload.

OMG!!! THIS WORKS!! I’m typically always expecting people are out to make you break your stuff more but this actually works!!! DIAG pops up on the top screen when pin 4. & 5. Are in an cars started. Shut the car off when beeping goes away, take wire out. Start her up an she’s mint!!

Can't beat the ole paper clip, enjoying your vids.

You are a good person, thank you for revealing the secret, otherwise they deceived me, they said you need to change the ABS Block and disassemble everything and remove the entire system, I wanted to go to the master the next day, he told me the ABS block costs $ 800 and for more work, for brake fluid and small things, almost more than $ 1000

I had this problem after changing the steering wheel, thanks for the video

Yayyy! It worked for my 2011 Prius, we had code c1336, BUT same flashing lights, traction, brake & abs.. we used ports 4 and 12! Worked like a charm! Thanks man! 💙

Muchísimas gracias si funciona oh man saved money thank you so much

This worked for my 2011 Prius. Thank you!

Your video is realy helpfull for me i have reset my prius lights thanks bro

Did some Brake work on a 2008 Prius and the lights came on. Did the reset trick by pumping 8 times after turn on. Waited for 30 seconds and everything is rest 100% AWESOME Thanks

My wife’s 2013 Prius was in a collision a few weeks ago and we just got it back from the repair shop 3 days ago. We had them then do an alignment because we felt the car drive differently after the crash. Fast forward to today 9/14/23 and all of a sudden ABS, (!), and BRAKE light came on. Started doing some research, suspected it was due to the alignment, and came across this video and another one that said it could possibly be due to that. Anyway, tried your way 3 times and it didn’t work. Tried it again while actually turning the car on, pumped the brakes 8 times, and turned it off. Restated it and BAM! No more lights! Thank you for your guidance. Just wanted to share what worked for me if anyone tried this and it didn’t work. Cheers!

Excelente en 2007 Toyota prius le cambié unas celdas de la batería hybrida y tenía prendida las luces del brake, abs, svc, ((!)), y funcionó🙏👍😊

You my friend are a money saver!

Such good info, really appreciate your video.

Thank you so much. Perfect video

You saved me bro, I really appreciate it you!

Awesome video. I’ve hit a curb with me front left tire on a 2011 Prius and 3-4 days after that these 3 lights came on. Drivability isn’t affected in any way, but they will just come on and off in short time of period. With the above said ( and I know you are not a magician nor fortune teller ), what do you believe the problem might be brother? Thank you in advance !!! Blessings and stay safe!!!

2010 Gen3 here. Im going to try this today. Hope this works before I take it to the Dlr.

Thanks for the video. Does this work on a 2018 rav4? My steering wheel is tilted to the right after an accident. If I align the wheels and correct steering positon, I get "lane departure alert malfunction" and "pre-collision system malfunction " messages and skidding light. Thanks

Will this work if I just have the vcs, abs and brake lights on after changing brake pads?

Is it PIN #4 & #13 on a 2011 Toyota Prius too? Also, does a 2011 Toyota Prius need 2-wheel alignment or 4-wheel alignment? Thanks!

Worked for me after I topped off Dot 3 brake fluid.

following this in 2024 :) which pins from OBD2 are you shorting ?, just to make sure it could work in a toyota highlander 2015

Worked. Thanks. Probably needs a new 12v. Original with 290k

So what pin # is it, on the OBD2 connector,on the 02 RX300 ? I don’t know which way you count it, left to right or right to left. And the connector facing up or down...thank you...

Will this work on other models like my Ford Edge

I replaced my standard Toyota Aqua/Prius C steering wheel with a leather Prius C one but now the new steering wheel is a little off centre.Will this reset procedure centre it?

Would this work on a 2012 Toyota Camry. I have the exact same lights on. And they came on after a wheel bearing replacement

Mate i just wandering to know is that same thing for Toyota kluger Kx-R 2012??? Tnx

Thank you

wow Nice job

Hello sir how are you and i hope you are fine and sir my question is. About electrical throttle body 0 calibration of Toyota cars and others vehicles is this reset work for throttle or not or it's only for staring calibration ?

Will this procedure work on Skoda Laura ?

Will this work on my 2007 Toyota Camry V6?

Great video , how you do in a 2007 toyota tundra? Thanks

@George Melnik I worked on the front Brake discs of my Lexus GS350 2008 today and after that, I asked a technician to scan the car for me with his machine and lo, ABS VSC & Brake lights came on! I've removed the battery terminals but those lights are still on. What could be the cause? Could it be the scanner cos I've scanned the car earlier this week and those alarms did not populate when the scanning machine was plugged. Could it be the scanner that triggered this? The code that came on on this scanner is C1203. Please advise what to do? Thanks in ad

Would this work for a 2l Renault Clio?

My prius 4, 2015, are the pins same 4 and 13? The ABS and Slip lights keep on recently, but no anything wrong when driving, didn't do any work on the car, am going to try this way. Do you think it is ok, Mr. George? Anybody knows what's wrong with it? Thank you.

Hello George Melnik, I took off the traction and AbS light off but it keeps turning on? I replaced the sensor because it read C0205 which is the left Sensor and made sure it works (continuity test) and the light is still on? I don't know if the 2010 Toyota Prius have a Reluctor? but it only shows that code and it does not make other noises. I noticed that sometimes the car skips and triggers the traction control light on. Can you please help me with this?

Sir i have a hard stearing in prius 2012, i just did alignment but stearing keeps on forcing a bit left side, also driving doesn’t seem plearuble. There is no code or lights, should i do this procedure, plz help me out

Greatfull Dear ☆

I have a ABS VSC code C1345 and B1650. Do you think Doing this will clear the codes? thx

i have a 04 Toyota prius i have repaird the Hybrid battery and now the Synergy pump , the Pyrmid of death triangle is still on no check engine lite no code , would this work for me ?

is this working on a Toyota 2007?

does it work for a 2010 prius 3 generation?

can this work for scion tc 2014??

That option works on the toyota prius 2013 ?? Between which pins are they ??

After a flat tire the traction control light has been on. Is a scan tool required to reset it? I'm looking into the Autel Mk808 since I also have to program new TPMS for winter wheels and also turn off the Maint' required light.

Hello george i have prius 2012 i just wanna know about my problem i m facing only traction control light due to some repairing done i repaired my steering clock cuz of horn problem and also performed front suspention and u know wheel allignment must have done now traction light goes on and i want to know is this video also resolve my problem ?cuz it must be angle senser calibration issue so plz guide me

THANKS BRO

For 2013 Lexus RX350 pin 4 and 13

Good morning sir please Where is the yaw rate sensor and lateral acceleration sensor located in lexus ES350 2007 cause the VSC and the ABS is on even the speed cluster is not working

CAN YOU USE SCANNER?

I have a 2010 Prius that I replaced all 4 hub assemblies on about a month ago. Now all of my lights are on including the hazard lights. Any ideas. I scanned it and got three codes. Both rear speed sensors and something else. Do you think this will help my problem. Any suggestions will be greatly appreciated

Can you tell this method work on crash car air bag light on car My stearing angel sensor is in -850 position

What are the pins what do thy do I need to do my 03 Avalon what pins do I use

Thank you so much . work on my prius 2005 . I jumped 4 to 13 then turn on then of the car dashboard turn off then after couple minutes dashboard light comes and abs light removed .

Does it work in Ford as well?

Thank You!!!!! will say on 04 - 09' Prius I believe i had to press the brake pedal fast 8 - 10 times in 5 sec. after lights go goofy 30 - 60 sec., then turn off... wait.. pull wire out... cycle power on again, pump brakes again 8-10 times, turn off... wait.. hold brake & start ~ that's the only way it worked for me.. ;) so jump wire, 4 in & 13 (5 in on bottom ) power button 2 x ~ wait 60 sec. ~ press brakes 8-10 times fast turn off ~ remove key, wait 10 sec., remove jump wire, ~ power button 2x pump brakes again 8-10 times ~ turn off ~ take out key wait 10 - 30sec. ~ put key back in & start! Wala : ) don't know if all that's necessary for every1, but it's the only thing that worked on r' 04 prius w/ the key fob u have to put in to start the car... ; hopefully will help somebody that the other basic steps isn't working for. ;

I wonder if this will work on a 2015 lexus RC

Can you do this on a 2003 town and country a Chrysler for got to mention

Hey George, I have an 07 Lexus gx 470, vsc, trac and anti skid lights on,what's the pins numbers on the obd connector, to reset those lights? Thanks

kan you show on obd port nummbers

Thank you.. i have one question: if i fuck it up and not do it right will it damage my car? Thanks

How would i do this on a 2003 town and country with the 3.8 v6

For me on my 2014 Prius Plug-in it was pin 4 and 12 And I had to let it sit for 1 minute until all the random sounds stopped and then turn it off pull pin and turn it back on

it shows out of stock. any other supplier?

Hi George, how to do this procedure on Nissan's Car? cheers.

is this good for toyota sienna 2002? or can anybody pls tell me what pin#s tu use ? thank you!

how do you take the cover off before plugging the pape clip?

Hi,i am facing steering angle sensor problem in Prius 2016 model Zvw50 and its a right hand drive car shall i conut the pins from right to left and will it work on 2016 model zvw50. prius. regards hassan

How about on a Nissan Titan 2010

Hi I got 2014 Toyota Corolla prestige. I just replaced an angel sensor because it was not working proper now the steering is very hard is like the is no power steering. Please help me what to do? Mbongeni from South Africa

Hey George, will this work on a 2014-2016 toyota fj150 landcruiser. I replaced the wheel bearing and VSC, ABS and park light went on..

Hi! I´ve tryed to do like in this video, but unfortunally... :( Is it one more way to fix the problem? Prius-30 2010

I tried this with my Lexus CT200h since it’s the same layout as a Prius, it’s still does not clear my abs vsc lights...any thoughts?

I just replaced the rack pinion today and the steering its froze My question is do you think is rack pinion came defective or I just need your method? Thanks

I did try on my Toyota. Prius. But did not work it was good but after I replace my rear brakes i go light on my car. Abs and brake and vsc

thanks you

IT didn’t work on my prius 2011 any other ways?

Please can confirm if your breaks got very hard to depress while driving when the lights came on

I have a 2013 Toyota Prius plug in and I got code c1203 and c1345 and I did the rest and it don’t work. What do you think what it is?

What if i replaced rotors

Thanks

How do I do this on a Chrysler 2003 town and country

hyundai ?

Hi I have 2002 Lexus lx 470 the car drive normal then one day morning I started the car I saw the brake light on and ABS on and trac control on can I do the same wat you do ? Number 4 and 13

Can u send a diagram of the plug to jump thx

For those that this didn’t work for try to erase the codes from a obd reader. I did it for my 2010 Prius. And the lights haven’t came back on “yet”

Hay my one is 2011 prius. I did wheel alingment 2 days ago and now the same light on. I went to mechanic and he did reset with computer but still showing all 4 lights. He is saying some air pressure issue and asking me to replace abs which cost more. Please advise will this work

I have code c1345 and c1368 2013 Prius. Got alignment done they stated the codes were stored and went on after alignment. Have brake light, abs, vsc and parking break light on if anyone can advise. I have tried this pin trick but didn’t work

This did not work I’ve try all of this vids I have a 2010 Prius I replaced the cv axles after this the abs and track control lights came on its given me a 1235 code it had a piece of metal on the hub I remove it still i by pass or jumped the 5 upper pin and 4 bottom , on obd port clear it still comes on and is hard to brake it sound like prack prack and the front wheels skip when I brake I did all this procedures when I brake the abs and traction light come back on dash board . Brake sensors are good I checked them clean them problem still persist , any tips what could be ? This is frustrating like I’ve said I’ve check the abs sensors are good no more metal in hub replaced cv axles after that this started to happen . I check fuses are good , I took car to get an alignment did not work steering wheel pulls to the left or right I try calibration like other vid says still same abs light come on and traction light as well if anyone had this problem , can you help , if I clear the code with paper clip light goes out , but car brakes like crap . I can hear the prack prack on front brakes and light pops right back on

Every time I make a right turn in my 2011 Toyota Prius, a sensor goes off and the warning that a door is open shows and beeps. I really need help with this problem if anyone knows what I can do please let me know, Thank you!

The fuel line increased 😂

Should there be any concern for an actual problem?

I have been getting the Check PCS System message. Any idea how to fix this?

How to set software on it

Hello Which are the pin holes? Which ones?