That rear bumper is 🔥🔥🔥🔥🔥🔥

Def very helpful been so torn between Stage 2 & 3

I put a deaver stage 2 on my 3rd gen TRDPRO. It went up 4 inches and drivetrain vibration was aweful. Required a 6 degree shim to eliminate vibration. My truck has a tonneu cover only added weight..tell your buddy to remove overload leafs and maybe one more and that should have him at 3” lift……still need a shim. Good luck

I don't understand how someone can spend 40K on a truck and add a block to the rear. Good video showing the correct way of raising the rear.

Very good video. I figure the basic concepts are similar with a Tundra besides part #'s and weights of course lol.

I would like to see these truxk with the stage 2 kit

Question! I have a 3rd gen taco. I am running a Decked drawer system (think around 150-200lbs) + Super Pacific X1 camper (300lbs?) + Rigd ultra swing arm with spare 35 inch tire and table. Think Deaver stage 2 or 3?

Another grate video. Thanks for the info. I am interested in the 1.5 leaf. By adding the leaf would it make the ride a bit smoother ?

Great video! After installing the lift/suspension do you still have the "taco lean"? If so, how were you able to address it? Thank you

Hi. I have a 23 Tacoma 4X4 Sport. I'm going to install the Bilstein 5100 and OME 2" coils on the front. If I do the AAL in the rear, wouldn't that just put the rake back to the way it was, only higher? My goal is to lift, but level the truck? Suggestions ? Thank You.

I hv the icon rxt’s on my Tacoma. Because I added a Decked storage system in the bed, have a Snugtop shell, and prinsu top racks my stick springs were negative flex. The Icons (full pack) gives it some rake. I just worry that the overall weight of stuff I hv is too much for the truck. How do yall handle all the stuff you put on ur trucks? Makes me want to remove the Decked system and get rid of a leaf.

What is the rige height change without the additional leaf on the icon . Thanks

So i want to replace my leaf springs. I'm not looking for that 'extra' lift height, since I don't haul heavy loads. ANy recommendation on type of leaf springs to replace the OEM??

With the deavers add a leaf. I've read that it says to take the overload spring out. Is it better to keep it in?

Can you please do more videos like this but with the tundra?🤙🏽

Great video, nice explanation of the difference between some of the major brands of leaf packs and AALs out there. I have an Icon Stage 4 and used the leaf pack that came with the set. Thinking about adding the 1.5" AAL from Icon for a little bit more height, it may allow me to adjust my front end a bit to match the rear and get rid of some minor rubbing. With all of that said, and most importantly, can that upside down G sticker be removed from the frame?

Hey what brand of rear bumper is that?

Thanks for the vid! I have the UpTop overland bed rack and the skycamp 2.0. Im going to eventually move to the RSI bed canopy with the skycamp 2.0. Should I go deaver stage 2 or 3?

Hey! So if I wanted to achieve a 3 inch lift in the front and 3.5 inch in the rear what would be my best option. I don’t have bumpers or a topper or anything, but I haul a lot of weight. I also like the look of extra rake when unloaded

Get vid! You guys usually always keep the pre load when installing the add a leaf? Icon recommends to remove it when installing there add a leaf. What are you thoughts.

Nice demo! how much weight is the back of Kyle's truck that he's getting that much lift out of the stage 3 deavers? if I upgrade leaf packs, would I need new shocks to compensate for the higher spring rate and change in ride height?

Off subject here but where can i get kyle’s “trd semi-pro” bed panel vinyl? I also love the r4t vinyl on the grey tacoma. Either way my tacoma is black and the truck is all blacked out, but looking for bed panel vinyl to dress it up a little.

Tuan what stage deaver is in your main setup on your 2017 trd pro?

Great explanation. So if I've currently got a 3"-2" lift package installed on my 3rd gen and go with something like the Deaver Stage 3, is that an additional 3" lift raising the total in the rear to 6" (within the load parameters, of course)? If so, can you raise the front to reduce rake as well?

who made the rear bumper?

How much weight in the back does that guy who switched to stage II have?

✌️