Hey Team! I like wearing black shirts but boy does it show the saw dust 😂. I placed timestamps below 👇to help you navigate this video. Good luck with your projects! New construction vs old construction 02:20 Safety first 03:33 How to replace an outlet box 04:09 How to run wire from outlet to switch 07:25 How to wire an outlet 09:32 How to set a switch box 13:44 How to wire a switch box 16:27 Final walk through 19:56
@johnnydez54812 жыл бұрын
Tt6
@richardwhite67022 жыл бұрын
I'm stealing power from a receptacle to feed 2 LED lights... I went from the receptacle up to the first light, then to the 2nd light, then to the switch... I'm not sure if the switch is faulty because I have constant power to the light now and the motion sensor/dimmer switch won't turn the light off and the lights are constantly on now... Should I have went from the receptacle, to the the switch, and then to the the 2 lights instead? Does it matter what order?
@davidicousgregorian2 жыл бұрын
@@richardwhite6702 yes receptacle to switch to joint lights and dimmers will work then but now its wrong by your decription unless you sent a 14/3 wire to both lights and dimmer switch from receptacle and in that case use the white nuetral from receptacle to lights and switch , and send power from black wire in receptacle and pigtail the black to power pigtail black to bypass lights straight to switch and leave red wirenutted away from receptacle (dont attach red to receptacle ) and tie red to lights and use red as switchleg silver screw from dimmer to lights then tie black onto switch for power and tie neutral white wire to switch if it is a lighted dimmer or if dimmer requires neutral and tie grounds to receptacle and switch and lights (if lights have ground screw)
@juanjuarez670311 ай бұрын
😊😊
@alanyoder7629 Жыл бұрын
I literally just did this. I’ve wanted a light in the coat closet for 40 years. The electrician who rewired the house refused to do it. Claimed no access. I finally realized the light could be a sconce above the left side of the door and not a ceiling light. I found an outlet in the basement just below the closet to pull the power. Drilled a hole inside the wall from below, ran the wire, and now we have another outlet in the dining room as well as a switched light in the closet. Only took me 44 years to get it, but no point in hurrying. 😊
@UrMomsSuperRichEx Жыл бұрын
God bless you “young man”, better late than never!
@hexZ066 ай бұрын
Old fart
@fjohnson88112 жыл бұрын
Very well taught my friend. I was always shaky on wiring for a new light but with your video I was able to install three recessed lights from an outlet. So glad I didn't have to pay an electrician for an easy job. Thanks again
@tonydurante2821 Жыл бұрын
I have a switch that turns a light off and on. Only 2 wires are on the switch. Can I get power from one of those wires (black) to power a outlet?
@mohammedmakba72672 жыл бұрын
Thanks for teaching, you are my favorite teacher who explains everything in such a beautiful way that a dumb like me have no problem understanding it, God bless you
@TheExcellentLaborer2 жыл бұрын
I appreciate that Mohammed! I try to explain everything in a simple fashion that everyone can understand. God bless you too!
@easttennessee9886 ай бұрын
Amazing perfect video for me today I am wiring a small office in my basement and need a switch to a light off an outlet this looks totally doable 🤛
@aussie-travelandtreasurehu76202 жыл бұрын
Found your channel by mistake, you have everything I need to know for my basement Reno plus more, glad Canadian code and equipment are very similar. You are freaking awesome, thank you
@jeffmykytiuk56429 ай бұрын
I appreciate all the hard work and explanations you put into making your videos. You are one of the best and most thorough teachers whose videos I've watched.
@hugogarcia7574 Жыл бұрын
This is the third video I watch. I like the detailed way you explain what you do. Thank you!🙂
@TheExcellentLaborer Жыл бұрын
Thank you Hugo! I try to add much detail as I can. I appreciate you watching!
@wx28332 жыл бұрын
Excellent content; I am wiring up a HVAC Blower Motor that I am using to build a heat collector for my workshop; I had it wired at 120v so it was running at half speed; which I thought would be enough since it ran an entire two story home in my previous HVAC package; but no joy. I have a lot of sensitive compute electronics that generate a lot of heat; So, my A/C guy suggested building a heat collector since 22 BTU's of A/C could not compete and was overpowered by the heat. I never wired up a 220v switch before; mainly just installed outlets, and some four prong, five wire three phase 240v locking outlets. I picked up a Leviton 3032-21 30a - 120/277 two pole switch; and since the draw is so low for the Blower Motor; I plan to piggyback it off a Metered 30a - 240v outlet; so this video was helpful. The reason I wrote this all out; is incase there is something I am overlooking; or something else I need to consider; since the outlet will be metered, ( and also tracks usage ); I can make sure I stay below 80% load to be safe. As a 90% disabled veteran after 25 years of service; I now work from home; to try and help my wife retire, and building personal data processing systems is something I can do; without have to burden anyone else to get the job done. I have to work with what I have left; since I cannot really use my body to create value these days. Thanks again for the straight forward; no nonsense instruction.
@richardphysician5640 Жыл бұрын
Josh, my man. If I could say I love you long time without it being weird I would like to. I just could not get it until I watched your video. Ty.
@TheExcellentLaborer Жыл бұрын
Hey Richard! I am glad to know my video was helpful for you. Be sure to subscribe for more videos to come. Thank you and take care!
@alvinsaulsberry3983 ай бұрын
Very helpful im learning not to be afraid of doing the work now thanks😊
@dewarfamily48622 жыл бұрын
Your videos have helped me wire my brand new 14x40 shed. Thank you for your help!
@TheExcellentLaborer2 жыл бұрын
That is awesome! Thanks a lot for watching my channel. Stay tuned!
@yepetoesca2 жыл бұрын
Finally someone shows the right way!!! Grate job. Thanks
@bobgherardi4392 Жыл бұрын
This looks to be spelled out simply and understandably. Was about to hire someone. Gonna do it try it myself! Thanks!
@larrybowers83232 жыл бұрын
The Excellent Laborer (Josh) looks like you got yourself some new work gear! (You need to get sponsored. Companies like Carhartt would be great!) Thanks for keeping the channel going and all your do to teach us to build our own houses and save a ton a money. Respect!
@TheExcellentLaborer2 жыл бұрын
It would be nice to get a sponsor! Thanks a lot Larry. I appreciate it!
@CivilianDan2 жыл бұрын
Learned a couple more things I did not know before. Thank you sir.
@TheExcellentLaborer2 жыл бұрын
Awesome! Thanks for watching Dan!
@Tiksunny Жыл бұрын
I found your channel by accident. You are awesome to help me some of the questions on doing the wires in the basement :) thank you so much for your channel
@thomasfoster5200 Жыл бұрын
thank you so much my friend you saved me a lot of money with your videos
@ronbunker57782 жыл бұрын
This is great for open walls during construction but not for finished walls.
@Raptor-700R2 жыл бұрын
Your video came up in my feed. I gave you and shot and boy do i love the way that you explain everything so clear. So yup uou got a new subscriber 😁👍👍
@TheExcellentLaborer2 жыл бұрын
Excellent! I hope you enjoy the rest of my channel. Thanks a lot for watching and subscribing!
@Rick_13375 ай бұрын
Perfect video. Gave me the exact info I was looking for.
@toolsiesampat27379 ай бұрын
You are doing a great job from your videos I have learned a lot thank you josh
@patrickarchuleta95942 жыл бұрын
God almighty bless you. Your work is second to none simply great may God continue to. Bottom line
@johnmurphyable2 жыл бұрын
These are some of the best construction videos ive seen on you tube!
@KevinCopenheaver-sh7mv7 ай бұрын
Super easy to follow. Thanks for your help.
@michaelclark4704 Жыл бұрын
This is a GREAT video. I've rewired the vast majority of my house, and I read a lot of manuals to ensure that I know what I'm doing: Stanley, Home Depot, Black and Decker, and many others. So I have a good point of comparison. This fellow is GREAT. He clarifies everything very well, and makes safety the first issue. Clear and instructions. Well done! One question: Does using 12 with 14 on the same line on a 15 amp service make any difference?
@davidroddini1512 Жыл бұрын
For 15 amps it is safe to use both. The problem is someone else down the road making changes might see the heavier wire and decide to upgrade the breaker to 20 amps without realizing that part of the wiring is not rated for 20 amps.
@deadmanswife3625 Жыл бұрын
@@davidroddini1512 exactly that is what would be the problem with it : people in the future if you believe in such a thing as life after yours😁
@juancuellar86627 ай бұрын
Good explanation, thanks for sharing your experience.
@jimholloway17852 жыл бұрын
I am enjoying your videos because they are real life situations that people are facing, so it is very informative and enjoyable to me. I have seen an increase of people using Wago style connectors lately but I don't see you using them. I was curious on your thoughts on Wago style connectors over the twist wire connectors and if there is a time to use one over the other? Keep up the great work. Jim
@brandonjensen52922 жыл бұрын
I changed old outlets today for the first time. Your content made it really easy. Thanks
@TheExcellentLaborer2 жыл бұрын
Hey Brandon! You are welcome. Im glad you see value in my content. Stay tuned for more!
@JuanGonzalez-wy8mo2 жыл бұрын
Nice explanation Now I’m going to do some wiring
@TheExcellentLaborer2 жыл бұрын
I appreciate you watching!
@albertramos3808 Жыл бұрын
Hey Josh, thank you so much that was a very good video, that is exactly the info I needed to add a light to a room that I built again thank you so much and have a fantastic day..
@silvergrizzly3162 жыл бұрын
HEY👋Josh!! This video couldn't have come at a better time, lol. I'm going to add a light socket over a work bench so I can screw in one of those 10,000 lumen paddle lights. I guess just jumping from the last outlet that the rest of the hanging led lights would be the same. Btw, I turn on my shop lights from two switches on the wall. I love your channel my friend and your detailed explanations!!!👍👍 ☆Jay☆ 😁
@TheExcellentLaborer2 жыл бұрын
Hey Silver Grizzly! It sounds like it will be very easy for you to add a light with that setup. I have not used paddle light before so I will have to do some research on those. Sounds like you have a three-way switch set up in your shop. I’m going to be doing a video in the future on how I do those. I’m glad you are finding value in my channel. Thanks a lot for watching Jay!
@designlife4living5472 жыл бұрын
Excellent work, well explained! Thank you.
@TheExcellentLaborer2 жыл бұрын
You are welcome. Thanks for the comment!
@froylanmunoz80092 жыл бұрын
@@TheExcellentLaborer thank you for excellent job I learned too much with you videos thank you thank you
@carlosportilla7634 Жыл бұрын
Josh! Like the way you makes splanation on your videos 👌👋👋
@TheExcellentLaborer Жыл бұрын
Thank you Carlos! I’m glad I can help!
@mharris150882 жыл бұрын
Thanks for that information, and thanks for your honesty.. and making this look easy.. 👀
@vincedidomenico44063 ай бұрын
Awesome! Thank you for the video. I want to do exactly this, but my question is, my cables have black, white, ground, AND a red wire. What do I do with the red??
@daddyslittlejunkies2 жыл бұрын
Nice. The only thing I see that I would have done differently is to run the wire through 3/8' hole from the other side :) so I only needed to pull 20"'s or so through instead of most of the cable.
@keithp115 Жыл бұрын
This was the absolute best tutorial for what I have been looking for without exception! New subscriber sir!
@TheExcellentLaborer Жыл бұрын
I am glad to hear that. Thanks a lot Keith! Stay tuned for more to come.
@26-CJ8 ай бұрын
@@TheExcellentLaborerCan I jump out of a 20 amp rated outlet box with 12 wire to another created 2 gang box that will have a 20amp outlet that is controlled by a switch. Both the new switch and outlet are also rated at 20 amps and wire is rated right with 12 gauge.
@manuelluna370 Жыл бұрын
Your video is very informative thank you
@TheExcellentLaborer Жыл бұрын
You are welcome. Thanks for watching. Good luck with your project!
@curtzeek8818Күн бұрын
You finally start at 4:10. I hope that tells you something.
@mississippiboi76Ай бұрын
What a good number for you I’m working on a tiny house and need some advise
@johntherat3392 жыл бұрын
This is clutch man! I need to power my well pump coming off an outlet and I'd like to be able to turn the pump on and off with a switch. Thanks for the great and timely video.
@CharlesHogan6 Жыл бұрын
Thank you sir! Well done.
@Gymjb53 ай бұрын
Thank you , I’m wondering if I can do the same to install a exhaust fan .
@TheExcellentLaborer3 ай бұрын
That should not be a problem for a standard exhaust fan. I hope that helps!
@Gymjb53 ай бұрын
@@TheExcellentLaborer thank you ,yeah is just a 6” inch wall exhaust fan for my shower ,now is possible for me to use 14-2 just to run the wire to the fan ? Because im running the wire from a old existing outlet,and im sorry about all these questions 🤦🏻♂️
@icaptured08622 жыл бұрын
Thanks for sharing your talent👍👍
@TheExcellentLaborer2 жыл бұрын
You are welcome. I’m glad I can help!
@darioarthur25252 жыл бұрын
great video...thanks But, people do not forget to put a metal plaque on the studs to protect the cable..
@evelio6778 ай бұрын
I like how you do that job thanks To share
@gailtaylor163610 ай бұрын
WAGO connectors would save you a ton of time.
@islenboi2 жыл бұрын
I'd like to add some would also put tape on that breaker with "Do Not Touch" while you're working on it, that way any who see it knows not to turn on without checking with the crew.
@marshmallowsti61352 жыл бұрын
Or use the proper breaker locks as needed
@weekendhomeprojects2 жыл бұрын
Great video! I'll be putting lights in a few closets soon so this is very helpful!
@TheExcellentLaborer2 жыл бұрын
Awesome! This should give you a few pointers for sure. I know this is a new construction job but is definitely relatable for a remodel too. Thanks!
@davidicousgregorian2 жыл бұрын
dont forget closets lights and basement and garages now require fully enclosed bulbed fixtures no closer than 12 inches from clothes and never above shelving ( pullchains and keyless fixtures are now illegal by code even if replacing broken fixtures)
@weekendhomeprojects2 жыл бұрын
@@davidicousgregorian what about cables recessed puck lights?
@davidicousgregorian2 жыл бұрын
@@weekendhomeprojects i will check do you mean plug in or direct wire from attic or walls to power source
@davidicousgregorian2 жыл бұрын
@@weekendhomeprojects Incandescent luminaires with open or partially open lamps and pendant-type luminaires must not be installed in a clothes closet [410.16(B)].
@arthurreece91552 жыл бұрын
Thanks awesome love your channel very informative
@TheExcellentLaborer2 жыл бұрын
Hey Arthur! I’m glad you are finding value in my channel. Thanks a lot for watching my videos!
@mrkayes12 жыл бұрын
This is what I needed to do my wiring. Good job keep it up. I have 2 questions 1. Can I use wire 14-2 for multiple outlet 2. Can I connect wire 14-2 and wire 12-2 together.
@davidicousgregorian2 жыл бұрын
first get a electrician for help and inspection of work before energizing ,theres alot of safety precautions and things non electricians dont know that vary per city and national electric codes now for questions 1. A 14-2 will supply 1500watts minus 20% for a 15amp circuit max on total circuit and yes you can use more outlets 1 in 1 gang box 2 in 2 gang box etc if all wiring from panel is on same 15amp breaker up to 1200 watts max for continuous use loads like ovens motors etc or 1500 for temp use lighting or receptacles(not always running at same time / and always consider NEC wire fill cubic inch rules.they added rules for grounds and new wire fill rules for everything in or connected to box or lights switches etc. dont combine with 12-2 wire ever and a general rule is 14 plugs and or lights combined on a 14-2 circuit max and 8 if all kitchen or bath or garage and exterior gfi protected serviced outlets lights or devices Microwaves fridges dishwashers disposals sump pumps dryers and ranges are to be on dedicated single use locations (dont get power from these) 2. never combine 12-2 with 14-2 unless you want problems with fire unless a qualified electrician helps you (14-2 can be tied with 12-2 if everyone knows what the reasons they can and cant tie together on this id always stick to all same wiring for safety and future repairs and wiring (easy answer is no)
@edwardogomez29192 жыл бұрын
Absolutely excellent video sir. Just what I needed. Thanks
@runforestrunchainsawcarvin34182 жыл бұрын
Well done! Thanks for the tips.
@TheExcellentLaborer2 жыл бұрын
I appreciate you watching and thank you!
@vaughan6719 Жыл бұрын
Great instructions. Very clear
@Victorvideos1 Жыл бұрын
Bravo well explained
@TheExcellentLaborer Жыл бұрын
Thank you Victor!
@elliothudsonhudsonhomesott2694 Жыл бұрын
Great video, thank-you! Drywall taper here - let me know when you need those boxes filled with mud. 👍 🤣
@richardlawrence31372 жыл бұрын
I am adding a light switch to my new shed, this video was perfect.
@georgeryan913911 ай бұрын
You do not leave any slack at outlets. I know you want to save as much cost as possible, but if there is a problem in the future, you could use some extra wire. You should fold back a little wire. You still have 6” length to staple. That is how they do it in the north east.
@amir990level28 ай бұрын
excellent Work. if the switch was close to the incoming wire to the first outlet box, what do you recommended ? is it possible to add a junction box first, feed the first outlet box and switch from this new Junction box? in this case we do not need to pigtail the three wires together and feed the Switch from the outlet box.
@anduanethlopez7942 жыл бұрын
Thanks brother
@TheExcellentLaborer2 жыл бұрын
No problem!
@justincooper16267 ай бұрын
Thanks for this
@jeanfrancois74702 жыл бұрын
Thankyou good job
@TheExcellentLaborer2 жыл бұрын
You are welcome. Thanks!
@THERE4fabrications2 жыл бұрын
Great video thanks!
@TheExcellentLaborer2 жыл бұрын
I appreciate that Sean!
@easttennessee9886 ай бұрын
Thanks!
@TheExcellentLaborer6 ай бұрын
You’re welcome! Thank you so much for your support. It means a lot. Good luck with your project!
@paelana2 жыл бұрын
Very Helpful, Thanks!!
@jsubs Жыл бұрын
Any videos showing how to install a new ceiling light using existing wall switch that controls a wall outlet. Thanks
@jaywildhorsepatterson4432 Жыл бұрын
Thank you
@TheExcellentLaborer Жыл бұрын
You are welcome, Jay!
@zacharyhall64042 жыл бұрын
This has got to be in the states, for plugs and lights we use 14/2 except for the kitchen that's 12/2.
@vero09922 жыл бұрын
Man, I didn't know those crimp connectors (as you had on the ground) are removable! I still had enough to work with, but I'll know next time to work it free instead of cutting it off.
@oscarfarley41042 жыл бұрын
a lot easier when you're doing the framing. But what about in a house that is finished and you don't want to start a new drywall project?
@dcbiglew Жыл бұрын
Nice and easy to follow. Did you do a follow up showing the final hook ups? Followed everything and want yo make sure that I get the switch and outlet wiring right. Thanks
@MaMa-qh4dy2 жыл бұрын
Excellent. Just subscribed!!!
@TheExcellentLaborer2 жыл бұрын
Awesome Ma Ma! Let’s build this wonderful KZfaq community!🔨
@Nationalist1019 ай бұрын
So to confirm, that box is always hot, right? So when you’d turn off the switch, the outlet is still live? I’m working on UN-pigtailing a three way switch in my house to free up a switch so I can add its own lights off of just that switch. I THINK the extra three way switch is wired off of the outlet below it
@bpwatx2 жыл бұрын
Great stuff man, thanks!
@daniel.j.rauscher2 жыл бұрын
Great video!
@connorsmith207 Жыл бұрын
When wired like this the outlets will have constant power on top and bottom right?
@sonny323 Жыл бұрын
I'm trying to change out a light switch to install a combo of light switch with wall plug/socket. And don't know what to do so I won't get shocked. Or burn out the fuse panel lol
@Turk412.73 Жыл бұрын
Great ! Now , I'm outside replacing std outlet w GFCI . From that I want to power a switch to another outside lite , both gfci & switch in 1 metal 2 gang box - will your procedure be right ?
@tweb32822 жыл бұрын
What do you think about using WAGO connectors? as An upcoming electrician it is being taught in school.
@michaeleverest34872 жыл бұрын
They make connections faster but over time the conductors can come out. Remember wire is vibrating at 60hz a cycle. They can come loose enough that you lose the circuit, or that enough heat is generated from arcing that you get a small fire in the box or big fire. I've seen it enough times to just keep using wire nuts.
@alexesco152110 ай бұрын
Hi I’m an a situation two outlets power from beaker box and wire going to light everything works but when I turn lights off outlet goes off as well?
@khymchristensen12377 ай бұрын
Is it okay to use a junction box between outlets to wire a switch/light if it's an older house and no outlet to wire into nearby ? And how many outlet/switch/light combinations can be on a 15 amp breaker circuit safely?
@AnthonySomes10 ай бұрын
Could you run a 14-3 from the switch to the light? With the 12-2 coming from the receptacle?
@tangamanga942 жыл бұрын
Thank you for the video. Why you didn't do pigtails for the switch like you did for the outlet? I thought that all lights switches also required the white wire to be installed.
@veegee34472 жыл бұрын
Gm josh thank you for sharing. I have question. How do you fix light switch?. when i turn it on the light doesn't come on write away
@TheExcellentLaborer2 жыл бұрын
Are you saying there is a delay when you turn the light switch on?
@ryanwilson6470 Жыл бұрын
Love the videos! It has helped me out tremendously on various projects 👍🏻. I need input on my application for my shop. I’m needing to add a light switch for four overhead lights. Is it safe to come off of an existing outlet that already has 6 outlets on the same circuit?
@MrTomad518 ай бұрын
I put a switch in a box to run off power to a ceiling light. I didn’t wire it a contractor did. The switch doesn’t go to light but to the outlet below it.
@Bewefau Жыл бұрын
I have a question. I already have light switch controlling a power outlet. What I want to do is take the light switch off the power outlet so its always on and can't be shut off. Than I want to take that light switch and have control a light or possible a fan light. They did not add any ceiling lights in this bed room.
@hinterlanderswellness9 ай бұрын
So is it possible to wire up all lights and outlets in a circuit with only 12/2? Or is 12/3 absolutely needed (assuming there are no 3 way switches)?
@virginian33902 жыл бұрын
Scenario: I have a 60W light bulb in the crawl space on the back of house near my water tank. I want to tap that fixture and run a cable under the house and out the front to install an outdoor outlet under my deck front porch. Question: Would that be a good idea and what size cable, 12? I believe the light may be the only fixture on that circuit.
@Mymusickb2 жыл бұрын
If the wire from the main panel that powers that circuit is 12 than you can use 12. If it's 14 then do not use 12. Use 14. Also dose that bulb run off a switch? If so you can't tap into that unless you want the outlet on a switch.
@Mymusickb2 жыл бұрын
I think also if you don't know for sure that bulb is the only thing on that circuit you probably should ask someone to help you that can be sure what you are doing is ok.
@anikettelang98316 ай бұрын
Will this work for using a light switch to add an outlet in a bathroom?
@weekendhomeprojects2 жыл бұрын
Social Blade has you at 900k views a month? Whats the RPM on building channels? About 4? So in that case you'd be pulling in about $3,600 a month in ad rev? Awesome job by the way, I ran across your channel early and was like....how does he only have a a few hundred subs, this content is gold.
@TheExcellentLaborer2 жыл бұрын
The channel has really started getting a lot of traction here in the past couple months. I am very thankful for it! If it wasn’t for viewers like you it would not be what it is and I thank you for it! My RPM is higher than that. I have noticed different videos have different RPMs. So it’s hard to give an exact RPM for any building channel because the content RPM varies a fair amount. My channel has always been directed to give people insight on projects. I hope that helps!
@tannerc9009 ай бұрын
Could this same application work for an exhaust fan?
@x7warrior7352 жыл бұрын
Awesome Job ⭐⭐⭐⭐⭐⭐
@user-vw2eg5el5v11 ай бұрын
I have 2 wires coming out of one conduit and 3 wires coming out from another conduit the only wire that is hot is the red wire the black wires are not hot. Want to put a new receptacle in the box with the light switch that was installed before how do I wire the switch and the receptacle in the same box that it was installed before. Please help me out. Thank you.
@uptondarden45462 жыл бұрын
When you turn on the switch on and off does it turn the outlet on and off?
@TheExcellentLaborer2 жыл бұрын
It does not is wired like shown in the video. Hope that helps!
@o.ggonzalez34702 жыл бұрын
Gracias maistro...
@TheExcellentLaborer2 жыл бұрын
Sure!
@lancer5257 ай бұрын
I've got a puzzler for you. (it's puzzling me, you might think it simple) I have one 14/2 coming from the panel, going to a single pole switch, operating a single led outdoor light. I want to add another switch off the same feed, coming from the first existing box, going to another switch (this one is lighted) for an interior light. Same feed, two different switches, two different lights, each operated by one of the switches. How the heck to wire that one up? Thanks!
@sargentnocap14147 ай бұрын
You have to tie it with the hot, neutral and ground off the existing switch.
@trailsloth69569 ай бұрын
Do you like the weygos? Or you prefer wire nuts?
@blokey51602 жыл бұрын
Nice video. Have you considered using the Wago lever nuts in place of the old fashioned twist-on wire nuts?
@TheExcellentLaborer2 жыл бұрын
Thanks a lot! I have considered those but I have not tried them yet. The tried and true wire nut has simply been my go to for years. If I had some I would definitely try some!
@lorenrickey54812 жыл бұрын
@@TheExcellentLaborerOnce you used Wago 222’s you’ll never go back.
@MaMa-qh4dy2 жыл бұрын
@@lorenrickey5481 The issue with Wago-type connectors is that they contact the wire on a very small area - like a knife. Yes, they are easy and quick, but the amount of copper wire to the connector is slight.
@TheExcellentLaborer Жыл бұрын
I recently tried WAGO connectors and like them a lot. Definitely easy to use!