Your videos are actually informative. MUCH more valuable than others on KZfaq.

Cool, I just learned something. I was replacing all the old philips screws on my bars with stainless hex, and when I was done my throttle was a little sticky, and didn't snap closed. Turns out a little play was needed by slacking off the nut a bit. Works great now.

NOTE: you can skip the advertisement portion by going direct to ~5:30 of this vid.

Just subscribed and liked your video... You explain way better than others...you go to the point and focus on the problem with details and facts.

I am soooo happy that your shop is as messy as mine... Love your vids!

Very informative video. Thanks. I had just adjusted mine at the grip end the best I could get was about a 1/4 inch fee play. The bike did not act up so I guess that was good

Cody you rock man. I have a few vintage bikes I've been working on and I'm telling you what your channel is amazing! Thank you so much good sir!

Subscribed! Nice video. Thanks for updating me with good knowledge. My CBF 125 has inconsistent engine rpm when cold. I've taken it to the shop, to check if it was needing valve check or injector cleaning/replacement. Mechanic answer that none of the above seem to be the problem. Since I couldn't get my issue fixed, I'm getting my hands on the bike. I suspect it can the the cable.

Cool, you explained why if it's too tight that can be bad. For my new scooter, I had a lot of free play from the factory. I found adjusting it at the throttle didn't work, the adjustment nut wanted to come off the threaded part before it was tight like I wanted. I set it about middle ways then adjusted it at the carb but now I'm going to loosen it at the throttle because I think it's too tight. Thanks.

I cant get enough of your videos. Keep up the great work!

Thank you. I got my fork seals replaced and noticed afterwards the idle would spike when I turned the handle bars to the right. I've known about the adjustment process but got stuff thinking it could be something more involved. Thank you for the reminder.

Really well edited video, it's both educational and funny, especially with the occasional mistake and train horn, it gives the video a little comic relief!

Please consider more tutorials on the 2003 Honda Shadow 750 when you have time. Appreciate all the effort it takes to create content for your channel. Cheers brother

Really enjoy your vidz dude. I own 1997 VT1100 ACE that needs some love and your advices come right handy. BTW, I work on trains so makes me smile when I hear it in your video 😂

Just got my bike from Honda of Norfolk and saw this video. I was like, I know I've seen him and I know that shop. Lmao. Great work. I need to adjust my throttle now.

Great video you really explained it very well .. I had so much free play rolling off the throttle and didn’t know why and it was sensitive rolling back the throttle now I know why .. fixing my bike now thanks

Love your videos mate :) Quick question about your 750 nighthawk, i think it's very similar to my 93 cb seven fifty that I'm turning it into a cafe racer, I've made a custom box to fit a smaller battery inside the swing arm but trying to figure out how to hide the wires, one thing I'm stuck... is what is the small black box that connects to the + side of the battery? I know part of it is a fuse but the rest of it is about the size of a relay. What is it and can I get a smaller one from aftermarket or another bike? Thank you for answering my question and I will give you a shout out in my wiring part of my cafe racer build.

Thanks again man your videos have pretty much put my bike together for me. Don't know what I do without you..... Yeah, I do. Who am I kidding? Throw things kick over my bike? Few choice words. You know the usual

Hey question for you. I have a 1996 cb750 that is in great condition. I am currently putting on some cafe clip on handlebars and new push pull throttle cables. I am have a hard time getting them to function properly. If the cables are straight the throttle reopens perfect with a snap. If I put the throttle on the handlebar, loop the cables over the headlight with a large loop and down the left side of the frame to the carbs, the throttle stocks open. HELP! What an I doing wrong?

Tq so much.....7 months nobody can fix my problem....with this video....I done my self...tq so much for the video bro ..

Best video out there yet because you explain which way to turn the cables to loosen and to tighten them, the reason for some free play and the all-important part about turning your handlebars both ways while adjusting. Thank you.

Awesome video man, fun, well explained and educational. Shame you haven’t opened your own DIY Bike fixing Center

Oh men this was so helpful men thank You Honda Jedi 🙏🏽

Great video 👏. I have a question for you , I friend of mine has a wr450f the idle speed seems ok , but when He is riding it and coming up to a junction and have slowed down , it seems to race on the throttle but if you let the clutch out when in gear and take it to the bite point it then drops back to normal idle ? Could this be an issue with the free play or return cable sticking ? I don't know much about bikes and any help would be appreciated.

i needed this video 2 weeks ago haha

Love the videos man, you are very articulate and the video quality is great. I'm working on cleaning my carbs on a 98 gsx600f and your video have helped tremendously. Keep up the great work.

What a terrific tip! Ya just made a new subscriber here.

I have a VTX 1300C, can you please help me out with the cable routing inside the switch housing and on the barrel sleeve.

Hey brother not sure if you'll see this, but I have an issue. I switched out bars on vtx and shaved off the nub on the throttle cable housing because new bars didn't have the hole drilled. It was fine for I while but now it slides around. What do you recommend? Tape on handle bar? Rubber piece?

Just followed your vid. Adjusted it to where I had practically no slack in the cable on my 1800 Neo. The lil turnbuckle lookin nut (adjustment nut) was like at 1 or 2 threads before coming off. Is it on, to have it on the last 2 or should I have bring it back in and set it ar 4 threads? Galfer cables & brake lines are my next big purchase.

Sweet video nice to watch an expert explain, any advice on how often to libel the cables? Good pace

Good video i dont mind Train adds to Video but can Imagine it gets on your nerves.Hello from England 👍🇬🇧

this is the best channel hands down. i will share for sure brotha. also you should do a video on valve adjustments if you can im new to the game and would like to see how its done for my vn750 or at all for that matter

I need help. I just did a hangle bar change myself and the handle bars look nice but whn i let go of the throttle it doesnt snap back. It just stays in the position i left it. Is that because i need to tighten my throttle cables

Excellent video! I could not make a sharp turn to the right without the rpm going up. Thanks.

All sorted thanks for your advice

Thnxs for the vid. I have a 84 Honda Shadow VT700c w/75,000 original miles. It sat for a while and boy did it backfire after I got it up and running. So I took off the carns and cleaned them up. But it stills rids a little rough. So I am thinkging its the carb and it need a tune up. I just need the reight specs on the idle screew . what screew I should start with and how many turns. Start with it all the way closed and back it out how many. Or open it all the way and close it down. Thanks for your brain power.

Hey I have a vulcan 800 but it has the same throttle set up as the one in your video, so I had to adjust the handlebars for my wife to ride this bike when I got a bigger one and I had to replaced the grips with some softer and when I was done I put everything back and I thought I put everything back together correctly but now it's backfiring or sputtering through the intake I can see the air cleaner hood bounce or shake or something it idles ok but if I turn the throttle a little bit it will chug and backfire so the only thing it could be is one or both of the cables are in a bind or something like that so does that mean I need to ger new cables or what? Thanks for any ides

How do you adjust the cables on the carbs i have sync’d the carbs all is good but when i give throttle the gauges go opposite of each other and i get a couple pops out the carbs

Hi, great vid, just subscribed. I have a slightly different "issue" with my throttle on two Dirt bikes i bought for my Kidz. The issue is there is the regular 2-4mm free play on the throttle bar, so that is fine. But my kidz are having trouble with that the respons of the throttle is too high. Its a 124ccm and 149ccm four stroke bikes. The feeling is you get full power just by the first 1/4 twist movement and the rest of the twist action does not matter much, since you already are maxed out. Is there an easy fix the reduce response action on the throttle or is this just how they work on four stroke bikes?

Hi mate! Loving your videos. Quick question... What lube are you using in this video? Also, do you see an issue in removing the push cable from a push/pull set up?

He man i need help with my bike i can not get it to idle what should i do first its an 83 cb1000

I have 2 Honda ST 1100's. one has what i consider normal , the other one has a " Hair trigger" throttle, and its annoying. So i need to figure out to adjust that, if possible ?

I could not find any video,pictures or step by step directions to do a throttle reinstall on a 1998 KLX 300. I also tried all the forums I could find.- Any help appreciated..

I took carb off because they were leaking fixed that but now I feel like I have loss of power like it’s kinda missing or something could it be throttle?

Helped a lot. Much appreciated.

I know it's an old video, but I had some issue with my Hornet. I also watched the video on turn light switch cleaning which helped me A LOT as all the other awesome videos you put here! Now, the ignition switch is sticky as well and sometimes remains on and lights go off... and since we are at the throttle cables: do I need to take off the throttle cables to take the switch apart and clean it? How? Cleaning I'll do it as in turn light switch I guess. It does not look like I can get enough play in the cables to take them off at the handle... Thank you again for the great content!

Do you have a video of removing and replacing the cables on this Shadow? Mine is 2002 VT1100C. Thanks!

Would it be possible to run the bike only with the pull-cable of the carbs? There is a spring by the carbs that will shut the throttle when one let's go of the handle

I jetted my carbs and my throttle is really stiff wont roll back to idol the cable is very smooth off the carb but when i connect it the throttle stays wherever i turn it to any ideas on what to adjust

Hey bro my bike 07 Suzuki after big rain my throttle is like no give gas to the bike ... like the speed screw is dinglin when the bike is on ? When I tight the speed screw is like run normal but after while the rpm go up ?? Helpme pleae

Hey man I have a 1997 rm250( close enough to a motorcycle) and I don’t have free play. It worked great until I changed throttle tubes and now it has no free play and does not return to neutral. When I first put them on, the throttle kinda locked and I man handled it back after opening it up and trying the different cams that come with it. I’m 98% sure I got the right one on, ive tried making the screws and bolts less tight. Any recommendations would be cool.

Thank you! Very helpful.

I think my problem is not so much the free play but that my throttle does not snap back fast enough. ("very very slowly") how can I fix that? I have already checked whether my throttle grips against something or hooks on something, but that is not the case

My freeplay is probably right in line with what you show when you flash "little dramatic..." on the screen. I'm talking a solid inch or more of rotation before engagement. My question is if the amount of pay is too much for the adjustment screw at the throttle is there another way to adjust or is it simply time for a new cable. Bike is an 07 shadow spirit with 110,000 km

I rebuild my carb on my 04 vtx1300 and after putting everything back on. My throttle is too tigh and it does not snap back on. I never touched the upper cable.i took everything apart again and no matter what is do the throttle grip is still tight

I have a problem there's no adjustment athe the top for my honda and no vide on how to do it at the carb. You mentioned it but didn't show. My throttle is locked fully pulled. Can't make it stop throttling.

The first adjustment is always to remove all slack from the deceleration or push cable at the carb and then you adjust for free play, me i always aim for the top and bottom adjusters on the pull cable to be in the middle of the adjuster with the throttle at 3mm free play

there isn't a video i can find on adjusting them at the carb so there's the right ammount adjustment available at the grip, sometimes ill see a bike with the adjuster all the way out to get the right ammount of slack because the carb side adjustment is wrong. i try to get mine so when the top adjuster is set its only open a 1/4 inch or less, but thats just me being fussy

Anyway you can do a full replacement video on throttle cables on a honda shadow ? i have been trying to find one for weeks !

Thanks pal helped a lot

Ordered the part today, need all the help I can get. Lol

What a great vid!!! Thanks a lot!!

When I loosen the the cable at throttle body the throttle sticks. Why is that ? Thanks !

Any tips on a CB 1000 find that the roll back is lose

SUBBED !!!! Great video. I loved it and was really easy to follow along. Cant wait for more content !!!

Is there anyway to shorten the throw or twist ?

I purchased a 2004 Gl1800 last summer with 180000km on it. I noticed after it sat for the winter, the throttle is super slow to retract. The bike has aftermarket heated grips (just wanted to note this incase it was important). I have tried lubing the tube under the grip with silicone spray as a hopes to an easy fix. It seems to have fixed my problem but the throttle still doesn't snap back like my 2013 CB500 does. Is the GL just slower in general to retract or should it be snappy like my CB? I love your videos! Keep em' coming!

So if the throttle is too tight, It needs some freeplay?

My throttle doesn’t snap back on my sportster, what could be causing that and how can I fix it?

Great video !

How do I reattach my cable to the handle bar

My bike wont start without the starter fluid and i have replaced the carb..the spark plugs..now the throttle is getting stuck. What cod this be???

Great info , hi from scotland ....

Cory, do stainless steel cables last longer or does it not matter as long as the cable used is properly lubed and adjusted? I'm trying to decide if stainless is worth the extra $. I wouldn't do stainless just for the appearance. (Other's opinions welcomed as well)

Over 5 mins of your video was for something other than the title. Nice you share a bonus. Hit the target 1st...then a bonus.

I always wondered why we need a throttle closing cable for carbs. Usually it's not even subject to any kind of spring load, so it doesn't "force" throttle closing by any means. However, if it gets stuck, it can prevent throttle opening. Anyone has a convincing answer that makes me think different?

I just changed the throttle cable on my 01 vstar and there is so much play in the handle

Thank you!!

Love the train bro

Very helpful, thank you! #liked

nice video!

Is any body knows where I can fine 2014 Yamaha vstar 250 throttle cables ?

Your dramatic is where mine is and I'm having a really hard time. 86 cmx450c

The red line pic at the beginning is actually a temp gauge

nice video very welldone👌

like 10 video watched but yours helpfull thanks a lot great work deserve subscribe

Great! Thanks!

Could you make a video showing how to adjust the cable at the carburetor? Trying to replace my grips and I don’t have any slack in the cable to get the old grips off or new ones on.

But i want a little more free play and on mine that adjuster is all way up cant adjust it anymore

"There's that awesome train again!" XD good vid man, keep em coming

Great my man do it again please

I understand that the "B" (idle) cable at the engine just has a lock nut and no adjuster, whereas the "A" (open) cable has an adjuster at the engine and handle ends. Is it just a case of sinching up B and then making "A" taught? Or is there something else to it? I don't get how the B cable doesn't require adjustment.

Why can't I find how to adjust at the throttle body

Great video man. I have a question. I have a Honda rebel 450 that I replaced the throttle cables on and I have no snap back on my throttle at all. I have to roll forward to turn the throttle back. So you think I need to adjust the cable or check the throttle tube?

I'm looking for a video but can not find one. My choke on a 2002 Honda Shadow Sabre 1100 will not stay on in the morning it feels spongy. I put the choke on and it moves slowly back down to half and kills the bike so I have to hold it myself. Do you have any videos on choke cables?

when u shim carb needles what size washer do u use

Thanks man

Thanks for the video on the freepay...I mean freepray....I mean... Free play. Ha. Question...I just changed my handlebars to something lower (clubman) and now my throttle is binding. If I remove the throttle and get the wire higher where it used to be positioned it does not bind. I know I may need some slight rerouting (hopefully that's all), but does this also sound like something adjusting the free play would correct, maybe without even rerouting? Or am a newb that is way off base with my assumptions. Thanks again

thank you for making this video! I am having a hard time how to fix my throttle cable. When I turn right or left, the engine starts revving on its own. I couldn't bring it to the nearest mechanic. I have to do the fixing on my own.