if the measurement is standard, why isn’t it set from the factory?

Love that you guys make these kind of informative videos, thank you!!

It's not clear from the video, am I supposed to set the length based on my lift height, then install it on the truck? It would help to have the rest of the install in the video, like when you put it on the truck. EDIT: i just read the directions that come with the track bar, all makes sense now.

As info, the crows foot is supposed to be at the 90 degree position if you are solely using the torque setting of the torque wrench. When you do it straight on at the 180 degree position, there is some sort of calculation that is needed to set the torque correctly.

Toby? From the office?

What size crows foot do you need for the updated black jam nut?

Red thread lock ?? Hell they seize themselves lol . Locktite on jam , anti seize on heir threads

Anyone know if this can be tightened while on the truck? Mine is loose I rather not pull it off if possible. My truck is an 04.5 so slightly different. The issue not many tools fit there I already tried, a crow foot might but not sure. I don't have one that big gotta buy one

You guys mention using the hitch to tighten the jam nut but with my 2015 ram 2500 the track bar does not fit in the receiver, am i missing something? Any other ways to tighten the jam nut if you don’t have access to a vice?

Your crows foot should have been at a 90 degree angle for proper torque. By having it in line with the torque wrench you effectively lengthened the wrench and most like applied too much torque.

For a wj with 4.5 lift what will be the length of the track bar

What size crow foot for the Thuren bar?

Can this be used with a relocation bracket? My factory bracket snapped and I have a ReadyLift Relocation bracket on the vehicle at the moment with the stock track bar.

If the track bar is loose, does it make noise on speed bump or while turning?

what is the measurements for a leveled front end which is usually 2 inches

What size crescent is needed for the Thruen bar? I found some contact on the driver side coil bucket when going 39 1/8th. Will need to shorten it by at least 1/2" to clear the bucket.

The Carli instructions say to adjust the track bar to 39-1/8" for 2.5"-3" Carli lifts. I ordered the 3.25" Backcountry for my 2018 Ram 2500. Is that 39-1/8" still a good measurement for me? Thanks in advance.

i think ill tack weld the jam nut 🤣

I have a 2005 Dodge Ram 2500 Cummins with a 3" lift . Will I still use the 39 1/8" measurement? With the Carli Track Bar. Thanks for all Your help...👍

Where'd you get the crowsfoot?

Interesting, as Carli says per their instructions to use anti-seize on the heim joint and Loctite on the jam nut?

I just put a 4” super-lift on my 2014 Jeep Wrangler jk how far off would the measurement be?

If you have added a 2" coil level kit, is the measurement still going to be 39 1/8" center to center?

How much adjustement for 2.5'' lift?

I am not clear on this but, if you do a lift kit and from what I have seen, it moves the front axle towards the divers side. Isn't this what the track bar corrects? If this is the case wouldn't the measurement be different than the 39 1/8"?

Is that adjustment the same for a 6" lift ???

So dumb question if I have a 6 inch lift but I have the 3 inch track bar drop bracket do I adjust the track bar for 3 or 6 inch lift!? A quick response would be awesome cj

Thanks. I'm sure the torque value on the jam nut is in the kit but just curious, what was it?

Could you do one of these for PMF and Superduty trucks?

I know I'm a little late but what is the measurement for my 2013 ram 1500 w/6 inch lift?!?.... Thanks in advance

I bought a Carli track bar but haven't installed it yet. What's the measurement for a 2015 F250 w/ a 2.5" leveling kit?

If you spend 70-100k on a truck, 4-14k on suspension,3-6k on wheels and tires spend the money on a professional install for example CJC off-road.

Hello. ok I have 2013 ram 2500, with 35 inch tires and with 2.5 in leveling kit. Does the 39 1/8 measurement work for this ?

What is the measurement for a 2017 f250 with just the Carli leveling kit ?

What's the length for a 20 250 tremor

Any specific reason why no one makes a cast iron adjustable track bar for a 2012 Ram 2500? It would be stronger than anything out there and may eliminate wobble from my truck and plenty others and a cast iron drag link and tie rod while your at it with replaceable tie rod ends. That is the only suspect I think on my truck now from trying to solve it for years , extremely frustrating. YOU listening ?

After setting and installing the track, bar is an alignment necessary?

If you ever have to readjust it, you better have a good torch..

Very nice job of explaining, thanks. Watched bds video first I highly suggest do not waste your time.

If you have a stock truck why doesn't Carli offer the bar already tightened down and sized properly, sounds like they are leaving the most important critical step in the hands of people who don't have the proper tools or a critical jig to make sure your getting the length and alignment Dead on. This method seems to throw the liability on the end-user.

Loctice dried up on me.. couldnt even lock it down after.. what do i do now😂😂