Thank you for teaching us "How to Build a 3s Li-ion Battery Pack". You made it so easy to understand. We all appreciate it very much. :)
@ciscocalderon5436 Жыл бұрын
You're welcome.
@alirezabaniasad5303 ай бұрын
Finally I got the point . I've watched a couple of videos and articles , but I just understood the process know . Thank you so much
@ciscocalderon54362 ай бұрын
You're Welcome! Thank you for watching
@scottgivens2710 ай бұрын
What's up brother! I just made a 300mah 3s Li-ion pack using your tutorial! Still very relevant. Charging now and test flying my 3.5" Prototype in a bit. Thanks!!!
@manski209 Жыл бұрын
Thank you for sharing this video. Thats exactly what i want to build for my 3" cinewhoops. Just for cruising and no crazy flying.
@ciscocalderon5436 Жыл бұрын
That's great. Thanks for watching.
@RobertJarosz-en8qn28 күн бұрын
Try using hot glue to attach the batteries together on the outside of the battery case to secure them togerher.Then you can use shrink wrap or electrical tape.
@ciscocalderon543626 күн бұрын
@@RobertJarosz-en8qn I did this video a few years ago when I first started making battery packs. I just did an updated video with improved techniques. I posted just a few weeks ago.
@harrisonbowie8293 жыл бұрын
thank you for the diagram.i looked and looked . yours made sense.
@ciscocalderon54363 жыл бұрын
Great! I was glad I was able to help you.
@Thomas-yr9ln2 ай бұрын
I have two power packs I ordered off of Ebay with four of these batteries. I got to power a headlight on my bike. They are covered with black plastic but they are the exact same color and size as these.
@matte.21455 ай бұрын
When I make packs, I use heat shrink tubing to secure them in and basically wrap them in. Tape works, but for a clean sweet look, the heat shrink tubing works well. just have to get some big enough! nice job tho!
@tygerfpv3 жыл бұрын
I don't trust myself to work with batteries, but cool to see how you can make use of these to make a bigger pack.
@ciscocalderon54363 жыл бұрын
Thanks. it's not too difficult, you just have to take precautions. That's one reason I don't use flux because that could drip into the cell and that's not a good thing.
@fishycomics Жыл бұрын
Perfect video. thank you Exactly what I needed to do mine and the shape as well. time to order some balance leads ,
@fishycomics Жыл бұрын
update did one without a balnce lead , simply easy again thanks
@RoninFPV3 жыл бұрын
Nice job. Didn't know how to do this til now. Keep up the good work 👊
@ciscocalderon54363 жыл бұрын
Thanks for watching. You gotta just do it!
@pcka122 ай бұрын
You need a new felt time, or better a rollerball, cos i keep being distracted by wondering if it will work, or that squeaky noise! Otherwise an excellent & helpful video!
@KODEEFPV8 ай бұрын
That marker sounds killing me
@jaxonbmx26997 ай бұрын
nails on a chalk board
@instantdough72203 ай бұрын
I buy a used driller battery and is the same also have some safety resistors or something elese
@michaeljacobs30152 ай бұрын
You are not supposed to put them closed to each order
@ronygarcia80792 жыл бұрын
Thanks for the video!!!
@coverdestroyer3572 Жыл бұрын
your tutorial is easy to understand, because of the number mark, do you have how to 4s tutorial?
@dnacannotchangeАй бұрын
.... I used the battery welder from temu....then use some Car jumper cable clips And clamped it to an actual car battery and welded it up at 68%... No I'm working on some type of strain relief So the wires don't get jerked and I'm frustrated...5000 mah li ion very weak n heavy...
@ciscocalderon5436Ай бұрын
@@dnacannotchange They have some battery spot welders in Amazon. Works great and super easy to use.
@Eric_Tennant Жыл бұрын
Best safe. On the top of each cell The negative is right next to the positive. Only a hair keeping them from shorting. solder could make a small bomb if it enters that hair crack.
@Eric_Tennant Жыл бұрын
Side note I have made mistakes on batteries that can be viewed on my channel.
@alirezabaniasad5303 ай бұрын
Thank you so much.I am just curious is there any way to charge this battery setting without parallel cabling ? And if there is , how should I set the charger?
@ciscocalderon54363 ай бұрын
I set it up like it's a Lipo battery. This way you charge the maximum 4.2 volts per cell
@timmytson13 жыл бұрын
Nice job
@ciscocalderon54363 жыл бұрын
Thank you!!!
@dnacannotchangeАй бұрын
....built e 3 cell 5,000 milliamp power Lithium.... Does it have any power and it only has a 900 milliamp power capacity.... Cycled it twice
@giuseppevillella94452 жыл бұрын
Ciao molto interessante il tuo canale complimenti 👍🔋😁🤝
@ericklein5097 Жыл бұрын
There is no danger in using flux and compared to the amount of time you spent on the cell (4 seconds then 8 seconds straight on 1, 8 seconds on 2, 5 seconds on 3 and about 5-8 seconds attaching the wire. Roughly same amount of time on the other side. So each cell gets almost half a minute of an 860 degree iron) it is way way safer to use flux. With flux you can be on and off in less than two seconds with the proper tip per attachment per side so less than 10 on each cell. Edit: plus balance lead time puts them at more than 30 seconds. Edit edit: Kapton tape will change your life but its not super cheap. I got 4 different sized rolls 1/4" width up to 2" width for $11