How to Build a DIY Spray Booth for Under $50

Рет қаралды 236,696

5 жыл бұрын

Get the Katz-Moses Magnetic Dovetail Jig here: lddy.no/stiz
Today we make a DIY Spray Booth fir under $50. Shaun Boyd just made a really cool book case and needed a place to spray it so we figured out the cheapest solution we could. Also chek out the video I made about how to spray HVLP Thanks for watching! Please like, comment and subscribe. Cheers!
Shaun Boyd Made This: / @shaunboydmadethis
Cheap EZ Up Canopy: amzn.to/2D0htTa
Painter’s Plastic: amzn.to/2WQR9Ct
Spring Clamps: amzn.to/2Vs1rsH
The BEST place to buy router bits: bit.ly/BitsBits
----
Buy the Katz-Moses Dovetail Jig: lddy.no/stiz
I have Walnut Slabs for sale: lddy.no/stj0
Buy The Katz-Moses Stop Block: lddy.no/stiz
The Katz-Moses Woodworking Apron: lddy.no/stir
----
Check me out on social media:
jkatzmoses
www.Facebook.com/katzmoseswoodworking
patreon.com/katzmoseswoodworking
/ katzmoseswoodworkingshop
----
Essential Woodworking Skills Playlist: • Essential Woodworking ...
----
Woodworking Joint of the Week Playlist: • Woodworking Joint of t...
----
Best of Katz-Moses Woodworking Video Playlist: • Making a Modern Bar St...
----
Tools I love:
The Katz-Moses Woodworking Apron: lddy.no/stir
My Favorite Dozuki Saw: lddy.no/stit
My Favorite Ryoba Saw: lddy.no/stiv
New Flush Trim Saw: lddy.no/stix
Dovetail Saw: amzn.to/2xi5EUV
Marking Gauge: amzn.to/2nlXLuQ
Marking Knife: amzn.to/2nm39Ok
Stanley Sweetheart Chisels: amzn.to/2mVMTkF
Knew Concepts Fret Saw: amzn.to/2FUDbYZ
Dewalt Planer Package: amzn.to/2thEf6O
Forrest 10” Combo Blade: amzn.to/2Fdaee3
Festool Tape Measure: amzn.to/2oS3cjD
Starrett 6” Combination Square: amzn.to/2oP3dVw
Woodstock 3 in 1 Shoulder Plane: amzn.to/2FgAS1A
Stanley Low Angle Jack Plane: amzn.to/2oV4I4O
Dewaxed Shellac Flakes: amzn.to/2FeqqYh
Abalone Inlay :amzn.to/2rjMTxe
Abalone Inlay Alternate: goo.gl/DHonFy
5 Minute Epoxy: amzn.to/2FijsSa
Triton 3 ¼ hp Router (with built in lift and edge guide incl): amzn.to/2LBw3Go
Kreg Router Plate: amzn.to/2A7oVNC
Triton Bushing Set: amzn.to/2A7pSpa
Bosch 1 HP Colt Router Set With Fixed and Plunge Base: amzn.to/2mHP1wY
Bosch Edge Guide: amzn.to/2uRRKs2
Bosch Bushings Set: amzn.to/2JUNRYb
Centering Cone: amzn.to/2OjgOAf
Avid CNCs of all shapes and sizes: bit.ly/3cdKdqA
Bescutter Laser (awesome c02 and fiber lasers) Website: bit.ly/bescutter
----
Camera Gear:
Lumix GH5-s and main lens: amzn.to/2J49F7m
30mm Macro Lens: amzn.to/2GJXtTT
15mm Lens: amzn.to/2NafUox
50mm Lens I use for product shots: amzn.to/2mehs5y
Microphone: amzn.to/2IGjKIa
Lav Microphone: amzn.to/2Nb8SzY
Gimbal: amzn.to/2s9ZV0F
2nd CAMERA Canon 70d: amzn.to/2FiCEDq
Tripod: amzn.to/2HasNvK
Slider: amzn.to/2oNucSd
24MM Wide Angle/Macro Lens: amzn.to/2oSzzjh
50MM f/1.8 for those tight shots: amzn.to/2tpAoVm
10-18mm Lens for the wide shots: amzn.to/2FZrhNM Axiom CNC (so awesome!): bit.ly/2J9RnPX

Пікірлер: 80

@katzmosestools 5 жыл бұрын

Check out Shaun's Bookcase Video Here: kzfaq.info/get/bejne/oZ6TmNiYpqmchqs.html Cheap EZ Up Canopy: amzn.to/2D0htTa Painter’s Plastic: amzn.to/2WQR9Ct Spring Clamps: amzn.to/2Vs1rsH

@ghostrangerp.8819 4 жыл бұрын

I must say that is a great idea I was about to purchase one when my wife told me that there are 2 of them in the garage that she purchased super cheap... I just put it up and works like a charm.....for various tasks....thanks

@makerlifeco 5 жыл бұрын

I've done a similar setup as a heated exterior wet tile cutting booth during a tile job during a MN winter. small heater and away we went!

@hotrodhog2170 5 жыл бұрын

The one thing I learned a long time ago about spray painting is to put the hose over your shoulder so it doesn't drag up against your project. The hose should just be long enough to reach out with your arm straight then going over the shoulder around the neck and over the other shoulder and under your arm then end up behind you.

@rodpotts2666 5 жыл бұрын

Great idea. Recently I have been thinking of some type of spray booth in my small shop this will work great just set up in the drive.thanks

@timort2260 5 жыл бұрын

I've done this before using tarps worked well and hopefully gonna find a cheap car port this year rather then my ez up. Also not sure if it helps but I used to spray air barriers on all sorts of building and to keep my respirator filters lasting a bit longer I use a cloth and wrap the filter and some painters tape to hold it on. Then discard the cloth when daily or even sooner if need be. And use baby wipes to clean any thing in or out of the mask after I leave the booth.

@chrishand259 5 жыл бұрын

Loving the videography. Nice montage shots. Awesome video as always.

@doreennewman7182 3 жыл бұрын

You're alright fella ! You're right, that was easy, I'm a senior, and amped up to go do my DIY projects !!👍

@alisameche5905 2 жыл бұрын

Thanks for how to do this and all your help on other woodworking!

@wb_finewoodworking 5 жыл бұрын

Great idea. I even have an old canopy that I could use.

@cody7855 4 жыл бұрын

Little late being a year old but a an idea, try sell "tarp zippers" that are just adhesive backed zippers. Could use slightly thicker mil plastic on one side and use that for the door. Would add a little to the cost but might make entering and exiting a little easier too

@danielrcarpenter1 5 жыл бұрын

"How's my hair?" Still perfect, haha. Great video.

@laurochavez9915 2 жыл бұрын

Usa a boxfan in one of the corners to get the fumes out! It works great

@namelessgarrett3052 5 жыл бұрын

Nice Dexter style kill room!

@mikedavidson7470 5 жыл бұрын

Yes Dexter!!!

@rchavez5056 4 жыл бұрын

What a great idea.

@KensGarage1 2 жыл бұрын

Thanks for the video. I will do this for painting motorcycle parts. Just need the plastic.

@garagemonkeysan 5 жыл бұрын

Great video. Is the red C10 next? : ) Thanks for sharing! Cheers!

@fcolon4 5 жыл бұрын

Brother, that’s creepy. It’s like you read my mind! You’re the best man

@Matlock69 5 жыл бұрын

Great video! I never thought to use a pop up, excellent idea. Quick PSA, tell Shawn he needs to get some cartridge filters like you've got, those pink 2097s don't do anything for airborne vapors.

@katzmosestools 5 жыл бұрын

I will thanks bud!

@jennasyseng 5 жыл бұрын

I agree, for an enclosed space (like a spray booth) the cartridge style will be more effective. The 2097s (for Organic Vapor) might be OK if you are just outside though ("Nuisance Level" but not concentrated).

@chrishand259 5 жыл бұрын

The way I learned was pink is for particulate, vapors require the cartridges.

@saritsotangkur2438 3 жыл бұрын

Yeah, you end up ruining your 2097 filters if you keep doing that. I have one one pair that ended up smelling like mineral spirits when you inhale (of course I ended up tossing that one).

@bp7770 5 жыл бұрын

I like the set up. Great I'd you dont have a dedicated booth. When building case work and cubbies, you should machine and prefinish your parts first then assembly. Its extremely difficult to get a great finish inside of a box due to overspray . I avoid spraying vertical, you cant lay an adequate amount of finish without sag and runs

@Nickporter17 4 жыл бұрын

I couldn't figure out why I was getting so many nibs in certain areas. Then I figured out it was just not enough material and the light coats were rough. Great tips!

@LTVoyager 3 жыл бұрын

bp 77 Yes, a booth should have some form of ventilation with filters. And once you learn to paint, you can paint vertical surfaces just fine without runs. Generally, the tricks are to use multiple coats with the first coat very light and then get a little heavier each subsequent coat. And having a good gun that is set properly.

@kapnkerf2532 5 жыл бұрын

The canopy in the video has a scissor-lke frame. The EZ Up Canopy on Amazon doesn't appear to. Maybe it changed? In any case, a great idea. I need a simple spray booth solution for my airless gun.

@johnbergeron3486 4 жыл бұрын

Thank you

@wesleywideman7185 3 жыл бұрын

That looks just like the loading dock and building that they used in breaking bad when he worked below the laundry.

@doranjaffas7351 3 жыл бұрын

This may be in some of the other comments answer wise but I'm wondering what you do use for ventilation to get rid of the overspray?

@MichaelBrown-kk6ck 2 жыл бұрын

Very little over spray is big advantage to HVLP.

@craigchingren-hamann9700 5 жыл бұрын

ONLY you could come out of a paint sock with that perfect hair!!

@ballybarn 3 жыл бұрын

How big does your compressor need to be? Mine is only 2hp 25 litres. Will that work with HVLP?

@mmr870 6 ай бұрын

Is that Shaun from foureyesfurniture in the background cleaning floor?

@bradleybritt9198 4 жыл бұрын

What type of sprayer did you use?

@tomalexander7313 3 жыл бұрын

What if I have a garage that I plan on dedicating to just paint?

@martpe2y 3 жыл бұрын

Bro this is awesome!.......and you look like Jimmy Kimmel

@Dc_tech386 3 жыл бұрын

I try this and all the fumes just sat back on the finish project as I am spraying I dont get this spraying both thing how the I get the spray fumes out faster

@andrewmvenegas 4 жыл бұрын

Decent video. Thank you. Every spray tent aI have come across in my research has a fan blowing out to create an out-flow for particulates. Wish you would have included that.

@zodspeed 3 жыл бұрын

Can this apply to painting car parts?

@matthewszostek1819 4 жыл бұрын

"Particle tight" thats the term youre looking for.

@EastwoodFabrication 3 жыл бұрын

Did you forget to include the part where you ventilate?

@MrAcgolem Жыл бұрын

Our local hardware store does a white PVC party tent with walls etc for under $100. It's quite big. Might have to invest in one of them. Thanks for the idea.

@age_of_reason 4 ай бұрын

Painter's plastic $20. It's now $37 🤣

@masonicmachine 4 жыл бұрын

I believe that using pvc piping would be cheaper.

@chrisstromberg6527 4 жыл бұрын

Not by much. This is a much better way to go for a temporary small spray booth!

@Bungowumperpuss 3 жыл бұрын

Tip: if you’re going to wear a half face respirator, make sure you’re clean shaven with no stubble or hair coming in contact with the mask seal.

@mikethebike2456 2 жыл бұрын

🏍️ That's a little over the top. You'll survive despite your stubble.

@Invis_Space 3 жыл бұрын

Anyone know what coating they used? 🙊

@jordanfessler9664 5 жыл бұрын

Were you spraying lacquer?

@katzmosestools 5 жыл бұрын

Yes

@The81titans 4 жыл бұрын

They make zippers for the doors

@purelybyimagination540 4 жыл бұрын

Cheapest helper, hahaha

@phillipemmons3714 4 жыл бұрын

Did I miss something? Where's the fan???

@FredMcIntyre 5 жыл бұрын

😃👍🏻👊🏻

@ozziejim8472 4 жыл бұрын

So no extraction fan?

@captainedc Жыл бұрын

Nice booth but you are forgetting 2 extremely important things. The fumes you are breathing from that less than adequate mask are deadly. Not to mention they can very easily create an explosion like you wouldn't even believe. One spark or static charge and BOOM. ESPECIALLY since you are letting them build up by not using a fan. Which needs to be explosion proof. Just sayin.

@orelygarcia 5 жыл бұрын

🧡💯😎👍👍🍺

@UpScaleClick 5 жыл бұрын

Video should have been called the easiest way to set up a paint booth.

@slixx008 3 жыл бұрын

The spray booth is better sealed than his respirator over his mask.

@sergiogutierrez10 5 жыл бұрын

Is it me or does he not look just like Jimmy Kimmel?

@katzmosestools 5 жыл бұрын

I get that almost every video

@mydemon 4 жыл бұрын

He reminds me of Jimmy Kimmel a bit

@Nickporter17 4 жыл бұрын

What kind of lacquer are you using? Where do you get it? I can't find quality precat in CA! You guys look like you're wearing bad breaking bad costumes with the highschool chemistry goggles JK!

@katzmosestools 4 жыл бұрын

Woodcraft has pretty good finish selection

@Nickporter17 4 жыл бұрын

@@katzmosestools thanks! Do you have a favorite finish that is fast drying?

@ShawnDBell 5 жыл бұрын

It's a a great idea, but depending on where you live, this is illegal.

@blahblahblahblah2837 4 жыл бұрын

Seriously? Where, if you dont mind me asking?

@clayvansickle1 4 жыл бұрын

What exactly is illegal about what they showed?

@cody7855 4 жыл бұрын

Please move!

@ShawnDBell 4 жыл бұрын

@@blahblahblahblah2837 Sorry for the delay. In Ontario, there's strict guidelines around spray booths, everything right down to the type of blades used on fans.

@ShawnDBell 4 жыл бұрын

@@clayvansickle1 Where I live, it's not permissible to use a temporary setup such as this, unless you're spraying waterborne lacquer, at which point I don't believe you're required to follow the same guidelines as if you were spraying something combustible. The main concerns are the environmental impact and safety. If for example, you made a setup like this and bought cheap walmart fans that had metal parts, and there was a spark, the entire spray booth could explode, that's why spray booths are designed so that all metal parts are grounded. A side note, where I live we're also not allowed to open five gallon lacquer cans on a table, you need to keep it on the ground and you can't steer it with a metal object (i.e, the screwdriver you likely opened it with).