Eh it was very hard for me to fallow and understand, but that why were all called an individual we all learn differently

Eh it was very hard for me to fallow and understand without any talking, but that why were all called an individual we all learn differently

Thats one reason why I made these. I hate power saws too :-)

Any hardware store will have it

They have them at Home Depot and lowes

@@Munky_funky6 lies, I’ve tried. They only have 1/16th in stock usually

@@cl4-tpgaming i was just at Home Depot today buying some maybe I was just lucky ???

This stuff is impossible to find in my area. Been looking for around 5 years and it’s never in stock anywhere. (Houston TX)

Hola amigo.

I build the simple shelves you see in the background of the video. I dont stack cages because the lights are best if outside the cage and because the cage walls can distort if they are not shored up with extra material.

Part 2 is on his channel

I agree. I always see videos like this "I made a cheap reptile enclosure with pvc" and i mean dozens of tbese videos and not a single person has a link to where they got their pvc sheets or even saying where and how much on the video.... baiting people for sure

should be your local home depot or lowes, just a local department store

The PVC is in fact the trim stuff from home depot. It also comes in 4x8 sheets of 1/2” and 3/4” Some locations you may need to special order though.

@@lukeschumacher6353 Im sorry you feel baited Luke :-) These are handi-panels from Menards or Home Depot. They are 4x2 sheets and cost about $35 each.

@@jmonahan1 😆Total BS, cheapest 1/2" 2ft x 4ft PVC sheet I could find online is $136.87 a sheet, Home Depot has absolutely nothing but thin & long trim pieces which are useless to this project. I called my local Rona and Lowes too, they said they don't carry anything close to 2x4 PVC. My local industrial plastics shop (which has the best prices by far) wants $120 per 2x4 sheet. So, yeah. Expect this project to cost upwards of $500+ when all is said and done. Manufacturers of reptile enclosures get their supplies at cost, that's why they can afford to make and sell them for $500. Making them yourself for under $100? Yeah those days are long gone. $35 a sheet, maybe in 2013.

You are welcome!

For these cages in the video I bought them at Menards. They are also available at Home Depot.

Best I have seen yet

Because I’m not a professional and I’m also trying to do some things similar with absolutely no guidance from anyone else… perhaps try cutting out a large section from the top and getting some screen mesh that’s sturdy enough for what you’re trying to use as heating and stapling it in with heavy duty, staples or seal it with silicone, whichever one you prefer; it won’t look beautiful, but it should get the job done. If you really wanna go all out, though, you can technically make removable screen squares, similar to what you see in the store-bought ones, and secure it in with some sort of bolt in clamp. I’ve seen this done on wooden enclosures and though it may be a little bit more tricky with PVC I believe you could get it done with some research. I hope this helps 🥺

Is a 4x2x2 big enough for an adult? To make a screen top, figure out how big of a square hole you need on top to fit your lighting and cut it out. Buy 1/4" stainless steel hardware cloth to use as screen. Cut scrap pieces of pvc or buy some extra trim boards to make a frame the size of the square hole you cut out, staple the hardware cloth to it and trim the excess hanging out, flip the whole piece over so the hardware cloth is on the bottom and screw it down to the top of the enclosure where you cut the hole out. That will make a slightly raised, neatly framed piece on top for you to sit all the lights on.

@@KylesMonitors yes that’s enough

Read comments above

Lol no they don’t

But prolly has a screen installed in the holes. I’m sure that’s eventually what this guy was intending to do with those holes

You could put a screen on the inside over the holes. Just make sure it's a fine weave so they don't try to push into it and scrape up their noses (I used chicken wire for this purpose once and my snakes were convinced that if they pushed hard enough they could get through the wires. 😑 lol)

No, I do not. But I think the construction is so simple that you could get together with a couple friends and try one. Even if its no good you will have learned enough to build a second one much better. Life skills :-)

Wrong stuff

The side panels sit in front of the back panel, so have to be 1/2 inch less deep than the top and bottom panels, which are 24 inches. The top and bottom panels sit on top of the back panel for structural reasons. The side panels are also the same height as the back panel so 24 inches. I have a video showing this Ill try to find it

The cost varies a lot with location and specific materials. But the 4 PVC panels are about $35 each. The vents are about $15 and the glass track is about $20. I use the thin glass that I get from the hardware store (window glass) because I dont have kids that could break them and get cut. If the cage is larger than 4x2 I would use a thicker glass like 1/8 inch. I used 1/4 glass for similar 8x3x3 ft cages, which is more expensive but much safer.

Each PVC sheet will cost you $100+ dollars so you're looking at $500 minimum.

@@peterh5417 Your information is wacky.

​@@peterh54171/2"x4x8' are 100$ a price. You only need one to do a build this size, plus the trim board.

@@peterh5417 Home Depot has a 4 ft by 8 ft sheet for $99. We made an enclosure using this video last week. The trim was an additional $10-15.

They are called several of names which makes it really confusing. But i believe you shouldn;t get the ones labelled as foams.. Those are the ones used in standeess and are not weatherproof.

These are 4x2 panels that are 1/2 inch thick. I buy them at Menards or Home Depot for about $35 each

lowes

@@2nd2none15 thanks

These are from Menards, but in some locations Home Depot and Lowes has them too. About $35 each

Yeah I found the 4×2 panels they was like $55 each the web site says they have the full 8×4 sheets but I didn't see them at the store thanks

@@charleshamby575 They are $35 here. The 8x4 are about $90

About a bazillion dollars or so.

I sauce you’re talking about heat lamps. No. Not hot enough to create fumes

Yeah i was talking about heat lamps, thanks.

Yes, you want to cut this material in a well ventilated area if you are using power saws. But once built you wont have trouble unless you lay a hot lamp right on the material itself. Dont do that! 🙂

@@jmonahan1 my RHP is attached to the top- should i do something differently? Attach something in between to buffer it?

​@stephaniebw4471 no your fine the RHP are directional the part that goes against the top is designed not to get hot for that purpose

Menards and Home Depot have them for $35 for 4x2 sheets. You can buy larger 4x8 panels which are less expensive per sq foot, but are harder to cut to size.

When I built the 8x3x3 versions I divide the front space with a support. You can actually see it in the background in this video when Im cutting the panel on the workbench. This way the front glass can be made up of 4 pieces, like 2 smaller cages almost. This makes the glass much less heavy and easier to slide.