You gonna race gingium once he goes to the 1.8 and 500 whp

I've been following you for awhile and have really enjoyed your videos. You're enthusiasm and passion is contagious and makes me proud to be part of the miata community. Your videos are currently helping me with an engine replacement on an 05 miata. I can't wait to the see the final results of your build. How is it that you don't already have 1 million+ subscribers already?! I live in Socal as well and the jokes you make about the cars or the sounds of your neighborhood crack me up. Keep up the good work. If you set up a patreon account, I would gladly contribute, as I think a lot of your other subsribers would as well. I hope to meet you at some point (once I resurrect my miata as well).

Best miata video by FAR! !I'm in London UK ..owed my M since 1990..always watch this channel. I salute u sir

Another tip: don't cut on the edge of the tape, but right in the middle. You can then immediately use the excess side of the line again for the next line without the need for a cleanup.

I've built tons of AN lines and you pretty much hit the nail on the head. And now anyone on the internet can see how easy it is and stop paying out the ass to have shops make them a "line kit"... Mind if I ask which brands of line and fittings you were using?

Quality production

Nice review! Thank you! It gets me excited about getting back into playing with cars!

i thank you Greg. I have been looking for a solid video on this subject an found some joke vids bout it. Again you have been helping me with my build an im pretty sure others as well why not post some fans build that u have been unkowingly helped. Idk if spelled right

Nice short and sweet. Diggin it. I need a car passion channel shirt btw

I love these little surprises!

Looks good! Great tip with the electrical tape.

Earned another sub. Great video!!

thanks, great work sir. :D

I legit needed this video like last week when my AN lines kept leaking because I wasn't assembling them correctly on my turbo miata setup haha

Awesome video very helpful!

Interesting...thanks for sharing!

If you go with the ptfe lined stuff that has the plastic coating around the outside of the braiding it’s much more of a pain in the ass to make the lines and to get the connector on the hose since the connector has to go much further along the hose. In that case you make the job much easier by sliding the connector on before you cut the hose.

What we used to do was to leave the tape on the line and then put the end piece on so you do not have to fight the "frayed " end when install the rear fitting , it just makes it easier to thread on.

That engine keeps looking sexier and sexier!

This is a good title for the video. You should get lotsa views off this one!

A mazda miata 1992 thats my dream car once i get it im going to get a miata and do build videos you have inspired me. I love your vids i look up to you and hopefully some day i will collab with you keep up the good work😁👊👍

Very nice dude!!

Awesome vid. So many people gloss over this.

Hey Greg ! great info all around, do you think there is a reason to buy a special tool for installing AN barb ? (koul tool...) thanks !

You really need to rinse out the hose with water or something once its all assembled. The rubber, nylon, and abrasive cut off wheel particles coat the inside of the hose after you cut it, and you REALLY don't want that in your engine.

If you are using the stainkess steel hoses make sure wrap the tape tight and dont take it off or the steel will want to go back straight and you will never get the fitting on.

Great video Greg! Do you generally prefer a specific brand for AN fittings? Also what are your thoughts on push lock setups?

👍keep up the good work

Thanks for making this video!

Just what i was looking for 👍

What am i doing here, I dont even own a mx5. Ow wait, I love the channel content 👌👍

Did you make a note of what fittings you used on this engine as I’m about to begin a vvt turbo build and would like to do this

Engine is looking soooo clean and tidy. Bet you stare at it for hours on end 👍🏻😂

Video is bang on! But can you show us how you do the oil feed and return?

invest in some aluminum AN wrenches. they prevent marring of the AN fittings. good video

Dude, your content, production is so dope... How can we help you get your subs up?

Greg, your hair....

This will definitely help when I relocate my oil filter.

Use AN wrenches doing that, way less of a chance of rounding off the flat spots since the metals are the same.

You should get the PTFE lines. With standard AN braided hose you will get fuel smells through the rubber hose. I ordered all mine through anfittingsdirect and they even come coated with a outer layer which is very nice and good quality.

how do tuners in CA deal with emissions?

Atta boy

Fastest like ever

I'm waiting to see if he makes it to MRLS.

What does AN stand for

Perhaps a dumb question, but I've never seen it explained before. What are the benefits of AN lines and fittings?

Actually don't bottom out the hose in the fitting shell, just leave a little bit of room

Hey greg, you said on your website the three places to buy an lines. Where did you specifically buy them.

Dang man. Now I want to redo my engine bay using all AN lines.

Does it matter whether the turbo is clocked up or down? I'm new to turbos

Is it possible to push 500hp from miata 1.8 engine? Because i saw gingiums video, where he claims that fully built 1.8 (stroked to 1.9) can push high 400s or low 500s

Dat length of the video😏

Any one know where I can get the type of material hose.

man...i tried doing an lines on my 75 280z for my fuel lines. that shit was leaky. given, i didn't know what i was doing at the time, 10 yrs ago lol

I want a miata so bad.. why they gotta be so expensive in my country ;-;

2019

Aren't AN fittings expensive?

Mate what's up with the videos assembling the engine?!

1:07 how the fuck did you tear that electrical tape! Are you a wizard?

you should cut through the middle of the electrical tape

When I order my an hose from eBay they used duck tape instead of electrical tape idk why but it looks like it works better then electrical tape. But an lines are a bitch

I willing to bet ricermiata will have blown the motor in the roadster by the time this ones running.

Video starts at 0:00

It's fourth video in the row with lenght of 4:20

Happy 4:20

Yea I'm having a fucking perfect day... I accidentally got brake clean on my fucking Rep ASA wheels and the paint peeled off. But I did wash and wax my car and install some parts so give and take.

The video is 4:20 long :0

Your hairstyle is still living in the year 2001😂😂😂

I own a miata, marry me dude

4:20 mins long ;)

You dont need to use electrical tape... It sucks at everything... Use scotch tape or duct tape.