Hope this helps! For Affordable, High quality PCBs Check out PCBways website! pcbway.com/g/HICmLg For my How to do SMD Soldering video: • How to do SMD Soldering! Thanks for watching! -Daniel
Пікірлер: 18
@kunal7biz2 ай бұрын
A great channel.. subscribed already.. keep posting.. its great stuff.. thanks
@prettymuchflawless-cn1ms2 ай бұрын
Thanks!
@mytechnotalent2 ай бұрын
Great job very helpful thank you!
@SystemBoo4 ай бұрын
saved you months of work. Thank you so much!
@wakhiwemathuthuАй бұрын
Well explained, thank you!
@benten344127 күн бұрын
Can you please make a video how to use the shell you showed? or give us the diagram?
@benten344127 күн бұрын
How it is converting 32 pins to 28 pins? Can you please explain the pinouts?
@unglaubichuberlieber80484 ай бұрын
very informative + detail, have you tried with those qfp(quad flat panel) chips ???
@prettymuchflawless-cn1ms4 ай бұрын
No I have not but I assume It would be very similar. there is some things you would have to change. 1. you will have to change the ATMega328 Variant to 328PB 2. watch out for the pin layout as it will be different I hope that helps Thanks for watching!
@dimitra.d79229 күн бұрын
hi can i read write program on atmega 8 microcontroller ?
@DBBahnospherix-BahnAtmospherix2 ай бұрын
Great - Question: can you now use the pins where the quartz is connected as GPIO? If so, how are these referred to in the program?
@prettymuchflawless-cn1ms2 ай бұрын
Not as far as I know. here is what the datasheet say about these pins: • XTAL2/TOSC2/PCINT7 - Port B, Bit 7 XTAL2: Chip clock oscillator pin 2. Used as clock pin for crystal oscillator or low-frequency crystal oscillator. When used as a clock pin, the pin can not be used as an I/O pin. TOSC2: Timer oscillator pin 2. Used only if internal calibrated RC oscillator is selected as chip clock source, and the asynchronous timer is enabled by the correct setting in ASSR. When the AS2 bit in ASSR is set (one) and the EXCLK bit is cleared (zero) to enable asynchronous clocking of Timer/Counter2 using the crystal oscillator, pin PB7 is disconnected from the port, and becomes the inverting output of the oscillator amplifier. In this mode, a crystal oscillator is connected to this pin, and the pin cannot be used as an I/O pin. PCINT7: Pin change interrupt source 7. The PB7 pin can serve as an external interrupt source. If PB7 is used as a clock pin, DDB7, PORTB7 and PINB7 will all read 0. • XTAL1/TOSC1/PCINT6 - Port B, Bit 6 XTAL1: Chip clock oscillator pin 1. Used for all chip clock sources except internal calibrated RC oscillator. When used as a clock pin, the pin can not be used as an I/O pin. TOSC1: Timer oscillator pin 1. Used only if internal calibrated RC oscillator is selected as chip clock source, and the asynchronous timer is enabled by the correct setting in ASSR. When the AS2 bit in ASSR is set (one) to enable asynchronous clocking of Timer/Counter2, pin PB6 is disconnected from the port, and becomes the input of the inverting oscillator amplifier. In this mode, a crystal oscillator is connected to this pin, and the pin can not be used as an I/O pin. PCINT6: Pin change interrupt source 6. The PB6 pin can serve as an external interrupt source. If PB6 is used as a clock pin, DDB6, PORTB6 and PINB6 will all read 0. Here is a link to the datasheet: ww1.microchip.com/downloads/en/DeviceDoc/Atmel-7810-Automotive-Microcontrollers-ATmega328P_Datasheet.pdf page 65 is where you can find this info Thanks for watching!
@DBBahnospherix-BahnAtmospherix2 ай бұрын
@@prettymuchflawless-cn1ms Thank you
@user-wc6vm8fw3s2 ай бұрын
I triple checked my wire connexion but i keet having the 0x0000 signature error. I Tried with an ATMega328-P U and an ATMega328PB-AU in a socket (with my IDE set for one of those) and i'm still having this error
@prettymuchflawless-cn1ms2 ай бұрын
is there a crystal connected?
@jeremiahbullfrog92885 ай бұрын
Brilliant! Where do you get the clamshell adapter? Looks expensive $$$$
@prettymuchflawless-cn1ms5 ай бұрын
From AliExpress here is the link: www.aliexpress.com/item/1005005925028098.html?spm=a2g0o.order_list.order_list_main.10.15ea1802UkmVN8 it was $20 so fairly inexpensive Thanks for watching!
@jeremiahbullfrog92885 ай бұрын
@@prettymuchflawless-cn1ms Wow that's a great price, got me a 44-pin one for my ATMEGA1284, thanks for the pointer