How to Change Arctic Cat Drive Belt 650h1

Рет қаралды 75,931

7 жыл бұрын

Get a New Belt for Your Arctic Cat here amzn.to/2ojSGze
today i'm showing you how to change the CVT belt on your Arctic cat ATV. This is also known as the drive belt. this requires you to remove the clutch belt housing. Once all the bolts are removed use a rubber mallet to gently tap the cover off. Then remove the nut of the driven pulley or clutch and remove. Then remove the nut of the driven or secondary pulley and pull that off with the belt. Installation is similar except you need to open the secondary clutch up when you install the belt.
Sound effects by Epidemic Sound
epidemicsound.com
Royalty-free music by Epidemic Sound
epidemicsound.com
Cameras used in My videos
Sony Hx80 amzn.to/2kUTNaF
Olympus TG-Tracker amzn.to/2dYKLZr
Sony A6000 amzn.to/1ROrgJl
TG-860 amzn.to/1VU6vzP
DJI Osmo amzn.to/1QDjGFb
Drift Hd Ghost amzn.to/1UUiZZU
SJ4000 amzn.to/2bel0jt
Vidi Action Camera amzn.to/1SaLBtu

Пікірлер: 53

@NLINE7 5 жыл бұрын

I just recently purchased a 2008 AC 650 H1 TRV a little over a month ago. I have been watching some of your videos and they have helped me understand somethings I've questioned. This is my first IRS quad. Thanks for the informative videos.

@SuperKax3 5 жыл бұрын

Don’t need to remove nuts just cover bolt like you did is fine. Had to do mine in the bush with the tools under the seat. Was a crap load of fun. Great vid be well.

@thebushbunker

Thank you this help me change the weights and belt in my o7 650h1

@ryandoe11 5 жыл бұрын

Thanks so much!! So many of your vids have helped me out, you're the man!

@jeffwillcocks8514 5 жыл бұрын

Replacing gasket on v-belt cover do I need gasket Sealant or just put it on dry

@kellychristian7836 6 жыл бұрын

I have a 2009 arctic cat 500 ATV auto. My secondary does not have the holes to put the cover bolts in to spread it. How do I do it to get the belt to the bottom while putting the belt back on with slack.

@ScottMcLinden 7 жыл бұрын

Thanks Jerry

@outdoorzone 3 жыл бұрын

Perfect!! I needed this vid! Your secondary looked a little different than mine! Mine doesn’t have that metal part that is over the spring just the nut and the spring retainer.

@nickolasedmunds 5 жыл бұрын

If the belt is bad and or slips will thr quad run at all?

@adamUDavies 4 жыл бұрын

How many times do you reuse the same nut's holding both clutches on ?

@danbudden6827 5 жыл бұрын

I have a 2017 mud pro 700 and the clutch cover bolt will not fit in hole to spread secondary clutch

@leonzios10 7 жыл бұрын

I don't know if it makes a difference but I have a 2016 500 cat and I did not need to remove either the primary or secondary nut. I just used a screw from the cover and expanded the secondary. That gave plenty of room to put the new belt on. Just to save someone from extra work... good videos BTW

@dirty.sanchez.gaming8016 3 жыл бұрын

my clutch rollers are out of place can i just put them back without taking it off? is it normal for the rollers to be out place when the belt breaks?

@TroyVossen Жыл бұрын

Good Video. Gave it a try to replace my belt on a 2010 Arctic Cat TRV. I tried to put the bolt into the secondary to separate. The secondary did not open and snapped. Now what? suggestions please

@Aldoleapold Жыл бұрын

Do you put red lock tight on the driven pully?

@toddhurley1237 5 жыл бұрын

hey jerry, I was on my 2011 450 trv today hauling wood ,when I heard a noise in the clutch housing ..now it wont move ..I can hear the primary clutch moving when I rev it, but it wont move..any suggestions??? thanks...

@chrissexton2355 2 жыл бұрын

I need to find the clutch specs 2003 mossy oak 500 four-wheel drive side beside where do I do that

@brayanhernandez214 5 жыл бұрын

I have an Artic cat 650 2007 but i doesn’t have no power it runs but doesn’t go as fast as a regular 650 and the belt is good any thoughts what this could be please ?