How to change your from and rear brake pads on a civic 2015 9th Gen music by Joakim Karud Dreams
Пікірлер: 60
@itallab495211 ай бұрын
what about lubricating the brake pad ears and the pin bolts? it's important.
@robbisSMACKD6 жыл бұрын
Thank you sir, I was concerned about pushing the piston back in the rear but needle noses worked for me! Thanks again 😁
@lauriegriffiths55502 жыл бұрын
Just changed front and rear pads on my 2015 Civic. This was a real help thanks but must advise that really you need a break calliper screw press for the rears. Twisting with pliers didn’t work for me and definitely needed the force against the piston alongside the screwing back. Save yourself the stress and purchase one before trying . Rears also we’re much trickier taking off and on the callipers. Fronts were a piece of cake.
@Nick-cs9dt6 жыл бұрын
Dont you need to undo the brake fluid cap?
@bobnoxious19835 ай бұрын
Just did my rear brakes outside in the dark! Great video thank you. caliper was very difficult to put back on.1 tip for putting the caliper back on. Loosen up the 2 bolts holding a brake hose on with 10mm socket. I had to use a 1/4 in socket and extension to reach it! That allowed me get iit just over the new pads
@Yettham Жыл бұрын
Just done my front pads and only cost me £32 and an hour of my time. I will tackle the rear breaks later on in the month. Thank you for your tutorial.
@rastojanosik6 жыл бұрын
Thanks for showing me how to change break pads on my Honda Civic. Good job.
@vinnybeckett40274 жыл бұрын
Please get a wind in tool, can be had for £15 - £20, one slip with long nosed pliers and that's your rubber piston seal gone! Little job becomes a big job. 😥
@stephenwhitemore17193 жыл бұрын
Thank you for your time and advice , helped a lot, easy to follow . Stay well stay safe
@canalboating5 жыл бұрын
Thanks for taking the time to make and upload this, just about to do this on my car which is exact same year and model so Hopefully there will be no surprises waiting for me.
@phillwildman6 жыл бұрын
Seemed nice and straight forward there. I have to do my berlingo van soon. I bet it wont go as easy as that, ;-)
@Cjrelectrical6 жыл бұрын
Phill Wildman might be lucky , but experience with French stuff , sticking , breaking,rounding and rusting lol
@TheJohny5896 жыл бұрын
Thanks you're the man it's hard to find exact videos of the same car you going to work on. Trying to stop the annoying squeaky noise from brakes could be my clip scraping the disks
@itsallrobbish2 жыл бұрын
Superb, just been quoted £400 for rear discs and pads for the rears, using Honda parts and Arnold Clark labour. Discs are fine, EuroCarparts are doing rear pads for £24.47 ! Hopefully sort it as well as you have. Love the chill hop music BTW.
@sorex_81734 жыл бұрын
Great job! Thanks On the rear can you tell me how you remove the caliper with the handbrake on it? Mine did not work....😔
@geoffreysantillan17635 ай бұрын
How do you adjust handbreak? I replace my break pads and now the handbreak is a bit loose.
@offbeatwarble6 жыл бұрын
The uneven wear on the rears can be due to lazy caliper or oxidation of the caliper where the pins pass through, the oxidation is between the rubber guide and the caliper itself, this then pinches the pin, it's worth removing the rubber guide and removing the oxidation else your new pads will end up the same. Notwithstanding that it might be the caliper itself.
@neilt7145 Жыл бұрын
You are spot on, I bought new slider kits from Autodoc at £3 a per, they come with two new slider pins, the rubber grommets and correct grease. Once you cut the old grommets out, get a round file and move all of the oxidisation away. Grommets are a bit fiddly to get in but with plenty of grease not too bad a job. Honda wanted £77 for an individual slider pin?????? WOW!!! £6 for both sides for all from Autodoc.
@BLADENFSMW1476 жыл бұрын
Would you be able to show where the oil drain plug is and the oil filter. New to the DIY jobs on my own car
@garethgalant88368 ай бұрын
Very well put together video. Found it very helpful as i did my pads today. Do you perhaps know how to adjust the handbrake?
@MrChadwicj2 жыл бұрын
Very detailed video, thank you
@666ortiz5 жыл бұрын
Thanks for the good video! This was useful set for cleaning Civic's stuck rear brake. It's btw good hint to mention releasing hand-brake to allow detaching the rear brake caliber, I initially made exactly that mistake and wondered how the caliber can be stuck so firmly :-D
@mikemontenegro94266 жыл бұрын
Good video ,,small comment if you leave the old pad in against the pistons,, just use a metal ( C ) CLAMP YOU JUST SCREWS INWARD, THEN IT WILL COLLAPSE IT.. DONE
@stevebeil9599 Жыл бұрын
Great video!
@hobgoblin93086 жыл бұрын
Those antirattle springs are a pain in the arse!!!
@kisangkim11053 жыл бұрын
My 2015 Civic does not have wires supporting the caliper. But it has 2 V shape thin wires(springs) to push the brake pads outward.
@casperaudi74765 жыл бұрын
Question Why would you pump the brakes unless you didn’t show the other side when if you change the brakes when finish all 4 then you pump brakes
@groundcontrol68765 жыл бұрын
What song is that playing? It’s the same one Jim from White Details uses a lot. Like it a lot.
@iPakistani3 жыл бұрын
Hi there is no clips on the caliper’s is it normal on this model ?
@Tintoycar Жыл бұрын
3:25 did they already make noise?
@hawk_ness5 жыл бұрын
You got a deal from Honda on their pads! Honda wanted to charge me £315 for fronts only... Told them where to stick that!
@hawk_ness5 жыл бұрын
Just did my pads and discs today and that spring/ clip too me longer to install than doing the rest of the job... 😡🤣
@Tintoycar5 жыл бұрын
Hi i finally got my MK9 (Belgium), great car!!! Question; is it possible to see mpg and how many miles (km) to empy tank at the same time on the display? Thanx
@Cjrelectrical5 жыл бұрын
You have to hold the I button until the mileage flashes then you can go through the menu.
@vedranbrozovic86665 ай бұрын
?? Main things you cutt out of the video 😅😅😅😅! Someone did it for you??
@tirolekubu85786 жыл бұрын
Did you have to bleed the rear brakes for the piston to retract?
@Cjrelectrical6 жыл бұрын
No just remove the brake fluid reservoir cap and push the piston back in . The fluid will push back into the reservoir.change the pads pump the brakes and jobs done .
@tirolekubu85786 жыл бұрын
The cjrshop I have been winding down the piston and it's not moving. I have opened the reservoir too.
@Cjrelectrical6 жыл бұрын
Reverse thread on them
@tirolekubu85786 жыл бұрын
The cjrshop if you mean I should twist the other way, i tried and that only pulls the piston further out. If that's not what you mean, please educate me.
@tirolekubu85786 жыл бұрын
It pulls out but doesn't go back in all the way. I used long nose pliers at first, thought that was the problem. I went and bought the tool and still no joy. 😢 I think the caliper needs to be replaced. Ahhh.
@ar-singh20804 жыл бұрын
Hi. Do you know if its easy to change the rear discs aswell? How would you take them off? Thanks
@jc-d61794 жыл бұрын
Fuzzy video
@yunhong1232 жыл бұрын
does anyones civic brake click because theres some wiggle room in the rotor? my pads slide and make clicking sound when going reverse to drive and vise versa. when i got the akibono pads for my front set, they were also sliding up and down. anyone have this issue? i have 2015 lx. i heard ex and si brakes are bigger. is this true? lets go civic community 🛶
@johndavies4644 Жыл бұрын
It’s either subframe click which is common or if you have a lip on the brake disc the pad will knock against the disc lip.
@yunhong123 Жыл бұрын
@@johndavies4644 I think it was just my pads were a tab bit smaller. I changed to a new oem set and they don't click anymore.
@slikund4856 жыл бұрын
Hi, thanks for the video ! Can you help me giving more information about the tool you use at 2:50 ? Thanks !!
@Cjrelectrical6 жыл бұрын
François I’m using a 3/8 flexi head ratchet with a 7mm Allen head socket .