How To check a Stabilizer (V-Guard iD4 Ace 5540 for 1.5 Ton Inverter A.C)

  Рет қаралды 35,572

Chandrabotics

Chandrabotics

2 жыл бұрын

V-Guard iD4 Ace 5540 for 1.5 Ton Inverter A.C
An air conditioner requires a constant power supply to the compressor and PCB modules. These electrical components are highly sensitive to voltage fluctuation. A voltage supply in the range between 180V-260V range is required for these components work efficiently. An excessive voltage supply due to a power fluctuation can cause considerable damage to the compressor and control PCB. These components are highly expensive to repair. This V-Guard AC Stabilizer is specially designed to deliver a precise power output voltage (180 - 260V) irrespective of any variation in the input voltage supply.
Cabinet with Wall Mount Slot:-
This stabilizer features a sleek cabinet design that allows you to wall mount it. Its design will complement the looks of you AC, wall and interiors.
Wide Operation Range (140V-280V):-
The V-Guard iD4 ACE 5540 is capable of handling a wide range of input voltage (90V-300V). It restricts the voltage output to an optimal output voltage to ensure your AC is functioning safely. Enjoy uninterrupted cooling while keeping your AC safe with this stabilizer.
Intelligent Time Delay System (ITDS) for you AC’s Safety:-
In the event of a power outage, this stabilizer will automatically switch on within three minutes if it has been in the switched-off state for three minutes. If the power outage lasts for longer than three minutes, the stabilizer switches on when the power supply resumes.
Thermal Sensor for Overload Protection - Safety:-
Your device can start overheating due to an excessive current consumption that is a result of component damage or internal short circuit. This V-Guard Voltage Stabilizer features a Thermal Sensor that can sense excessive current consumption to effectively disconnect the power load, thereby preventing your appliances from burning out.
Safety Features:-
This V-Guard iD4 ACE 5540 stabilizer has safety features such as low and high voltage cut-off, smart output voltage correction, initial time delay.

Пікірлер: 69
@vikky6699
@vikky6699 Жыл бұрын
great helpful video! no nonsense! Thank you!
@aniruddh01afterburn
@aniruddh01afterburn 2 жыл бұрын
Brother , I think , you could have added another multimeter for the output voltage of the Vguard stabilizer. So that , it can be checked , if the output voltage that's being shown on the Vguard Stabilizer's digital display , is same with actual output of the Stabilizer or not. That would have been more accurate test.
@Chandrabotics
@Chandrabotics 2 жыл бұрын
Thank you so much for your suggestion ❤️🙏
@riktamsarkar7684
@riktamsarkar7684 2 жыл бұрын
@@Chandrabotics My input and output is showing the same. Can you please help me, it shows196 input and 196 output.
@KumarShanoo
@KumarShanoo 2 жыл бұрын
Great bhai👍
@Chandrabotics
@Chandrabotics 2 жыл бұрын
Thank you brother ♥️
@fahedkhan2732
@fahedkhan2732 2 жыл бұрын
good video dear. Hard work.
@Chandrabotics
@Chandrabotics 2 жыл бұрын
Thank you so much ❤️
@fahedkhan3008
@fahedkhan3008 2 жыл бұрын
@@Chandrabotics Dear brother, you deserve it.
@30mAkills
@30mAkills Жыл бұрын
Testing without load is useless. Stabilizer should be loaded at least 50percent for accurate results. Using Variac is correct method of injecting voltage. Hope you don't mistake me.
@Chandrabotics
@Chandrabotics Жыл бұрын
Thank you Sir for your advice 🙏
@user-hm1cn9tl1x
@user-hm1cn9tl1x Күн бұрын
How much Kva for this stabilizer
@siddharthb9843
@siddharthb9843 2 жыл бұрын
Delay is of how much time?
@Sarfoo93
@Sarfoo93 2 жыл бұрын
How much power is required for Carrier 1.5 ton 3 star non inverter AC?
@viveksinghrajput1710
@viveksinghrajput1710 2 жыл бұрын
Google search
@sampadmajumdar1683
@sampadmajumdar1683 Жыл бұрын
Can u help me with one of my problem regarding this stabilizer?? If i switch on the stabilizer, the delay is blinking continuously and the red light is not changing to blue light...Is my device faulty??
@Chandrabotics
@Chandrabotics Жыл бұрын
Yes. I think you already contacted with the customer care.
@pritamhait
@pritamhait Ай бұрын
দাদা নীল লাইট টা যখন নতুন কিনেছিলাম বেশ জোর আলো দিচ্ছিল কিনতু এখন ২ মাস পর দেখছি যেন নীল লাইট tar ব্রাইটনেস টা যেন কমে গেছে। এটা কি আপনার ও কমে গিয়েছে নাকি আগের মতন জোরে জলে?
@Chandrabotics
@Chandrabotics Ай бұрын
Na Bhai. Amar to ei rakom kichu hoinei. Jodio ete kintu kono problem nei.
@pritamhait
@pritamhait Ай бұрын
@@Chandrabotics প্রবলেম হচ্ছে না ঠিকই, কিনতু নতুন জিনিস এরকম ফল্ট তাই ।
@biswajitsantra7861
@biswajitsantra7861 5 ай бұрын
Is this stabilizer have copper winding??
@vinodar86
@vinodar86 3 ай бұрын
Its aluminium
@mritunjai1715
@mritunjai1715 2 жыл бұрын
I have purchased the same stabilizer I have a doubt kya stabilizer ka fan continuously chalta hai ya jb voltage km ya zyada hota hai tb. Because I am getting input 233-235 and output 228-229
@Chandrabotics
@Chandrabotics 2 жыл бұрын
E normal hain. Apka stabilizer acche se kam kar raha hain.
@prasadjadhav3837
@prasadjadhav3837 2 жыл бұрын
Mera wala fan to chalta hee nahi aur trip bhi hota haii kya kare
@viveksinghrajput1710
@viveksinghrajput1710 2 жыл бұрын
@@prasadjadhav3837 bhai mjhe bhi ek lena h Ye lu ya VWI 400 LE LU
@sanjoymisra5309
@sanjoymisra5309 11 ай бұрын
Is the side exhaust fan work or not?
@Chandrabotics
@Chandrabotics 11 ай бұрын
Yes but when needed then only it will work. It has very little noise.
@aniknarayan1692
@aniknarayan1692 Жыл бұрын
Hi friend, stabilizer makes kat-kat sound when voltage goes below 200V, is this normal ? please reply
@Chandrabotics
@Chandrabotics Жыл бұрын
Yes Normal.
@ShehjaadePrince
@ShehjaadePrince Ай бұрын
When side exhaust of this stablizer work?
@Chandrabotics
@Chandrabotics Ай бұрын
Thanks for your question. The fan will only work, when the stabilizer will be hot. It is a very silent fan.
@CAPTIONBAPI
@CAPTIONBAPI Жыл бұрын
Blue colour ka ring led light ek side jal Raha hai or ek side nahi jal raha hai kaise thik karwaye Model - Vig Stabilizer 400
@Chandrabotics
@Chandrabotics Жыл бұрын
Ap company main call ki jiea. 1800 103 1300 is number pe. Apka model Sayed abhi bhi warranty main hain. Free main replace ho jayega.
@CAPTIONBAPI
@CAPTIONBAPI Жыл бұрын
@@Chandrabotics ok
@gamingend6799
@gamingend6799 2 жыл бұрын
Bhai koi aise stabilizer batao jo 50 extra jana kar de
@kartikjagdambe8114
@kartikjagdambe8114 6 ай бұрын
Please check On load
@sahilshaw3217
@sahilshaw3217 2 жыл бұрын
Sir mera same stabilizer ha but owo kabhi kabhi output 197 ke niche reta hai but input 220 ke upar hota ha l, kya apka vi hota hai ? Please reply kare sir.
@Chandrabotics
@Chandrabotics 2 жыл бұрын
Ekbar main bhi e notice Kia tha. Magar uske bad kabhi Nehi hua aisa.
@sahilshaw3217
@sahilshaw3217 2 жыл бұрын
@@Chandrabotics ok, ise koi problem toh nahi hoga? Kya yeh normal ha?
@titobanerjee1085
@titobanerjee1085 2 жыл бұрын
Mera 1.5 ton ka career ac hai. v guard id4 ace 5540 stabilizer mein in. Put maximum time i.p 240 se 235 aur o.p 201 - 202 andar rahata hai aur kuchh kuchh time mein jab o. p badhta hai ya kam hota hai uske sath ac ka speed bhi kam jyada ho raha hai .sahi hai ya nahi?
@Sahanawaj_
@Sahanawaj_ 2 жыл бұрын
Ac kharab ho jayega return kar do faltu stabilizer hai
@Sahanawaj_
@Sahanawaj_ 2 жыл бұрын
Maine bhi same problem face kar raha hu. Iss stabilizer ki sirf look achi hai koi kam ka nahi hai
@Sahanawaj_
@Sahanawaj_ 2 жыл бұрын
Isse lo problem solve ho jayega
@spawn6977
@spawn6977 Жыл бұрын
@@Sahanawaj_toh fer konsa liya stabalizer
@Sahanawaj_
@Sahanawaj_ Жыл бұрын
@@spawn6977 Microtek PEARL EM 4150+For AC upto 1.5 Ton AC Automatic Voltage Stabilizer-Standard
@pritamhait
@pritamhait Ай бұрын
After 2 month use of stabilizer blue ring light brightness level low seeing ... anyone noticed it? Or its my wrong thinking..
@Chandrabotics
@Chandrabotics 15 күн бұрын
For me it is still ok.
@pritamhait
@pritamhait Ай бұрын
After 2 month use of stabilizer blue ring light brightness level low ... anyone noticed it? Or its only with me ?
@Chandrabotics
@Chandrabotics 15 күн бұрын
Still it is ok for me.
@prasadjadhav3837
@prasadjadhav3837 2 жыл бұрын
Iska fan chalu kab hota haii me new liya aaj AC ke liye install bhi kiya lekin uska fan nhi on ho raha haii what can I do
@tarunsharma5254
@tarunsharma5254 2 жыл бұрын
Bhai fan tab hi chlega jab ye heat hoga , fan nahi chl rha to bdia hai.. fan ka avaz bht irritating rehti h
@bhupeshnegi3004
@bhupeshnegi3004 Жыл бұрын
Ye copper me hai ya aluminium me
@Chandrabotics
@Chandrabotics Жыл бұрын
I couldn’t find any information on whether it’s made of copper or aluminum. However, it’s worth noting that copper is a better conductor of electricity than aluminum. I hope this helps! Let me know if you have any other questions.
@werewolf19
@werewolf19 2 жыл бұрын
Sir kya is steplizer me use karte time noise aati hai
@Chandrabotics
@Chandrabotics 2 жыл бұрын
Yes. "Katak" karke ek sound hota hain.
@asu-ku1oq
@asu-ku1oq 4 ай бұрын
bhaii english tense ke hisab se bol rhe hai 😅😅
@Chandrabotics
@Chandrabotics 4 ай бұрын
😁😁😁😁😁
@Kumar-kt8st
@Kumar-kt8st 2 жыл бұрын
Sahab Hindi mein bata do
@Chandrabotics
@Chandrabotics Жыл бұрын
Sahab Nehi bhai. Mera bahot dikkat hota hain English batane main 😟
@Sahanawaj_
@Sahanawaj_ 2 жыл бұрын
Faltu stabilizer hai mat lo koi bhai 230 ki input mai 204 k output de raha hai ! Bakwaas maal hai
@TeilorJoe
@TeilorJoe 3 ай бұрын
চন্দ্রবটি 😂😂😂 😂
@Chandrabotics
@Chandrabotics 3 ай бұрын
চন্দ্রবোটিক্স...... ব্যাপার হচ্ছে আমার নাম চন্দ্রচূড় ও আমার রোবোটিক্স সম্বন্ধীয় চ্যানেল বা আমার পছন্দের জায়গা। সেই জন্য Chandrachur+Robotics=Chandrabotics
@TeilorJoe
@TeilorJoe 3 ай бұрын
@@Chandrabotics Na na bhai, Name and Channel name nie kno apotti nei.. ami just ektu moja krlam.. but video ta enjoy korechi last obdi..
@Chandrabotics
@Chandrabotics 3 ай бұрын
@@TeilorJoe Thank you 😊
@prabirbhattacharyya1938
@prabirbhattacharyya1938 2 ай бұрын
Sabse bekar stabilizer 😂
@Chandrabotics
@Chandrabotics 2 ай бұрын
Apko kuch issue ho raha hain? Mera ekbar hua tha issue to company se phone karke thik kar lia. Abhi to sahi se chal Raha Hain.
@prabirbhattacharyya1938
@prabirbhattacharyya1938 2 ай бұрын
@@Chandrabotics Yes Sir. When voltage is in low range 200-220 it always diminishes voltage by 2-5 Watt instead of making it to 230-240. It displays 200 to 215 Watt. Company person came saying it quite natural . He said that only when voltage goes below 200 then only it will upgrade the voltage only which is contrary to stabilizing theory. An AC needs 230 volt to operate smoothly. So the stabilizer is a vague one in my point of view.
Secret Experiment Toothpaste Pt.4 😱 #shorts
00:35
Mr DegrEE
Рет қаралды 37 МЛН
Amazing weight loss transformation !! 😱😱
00:24
Tibo InShape
Рет қаралды 65 МЛН
Я обещал подарить ему самокат!
01:00
Vlad Samokatchik
Рет қаралды 9 МЛН
Inside Out 2: Who is the strongest? Joy vs Envy vs Anger #shorts #animation
00:22
How To Install V-Guard iD4 Ace 5540 for 1.5 Ton Inverter A.C
9:10
Chandrabotics
Рет қаралды 73 М.
ID4 ACE 5540 V-GUARD Voltage Stabilizer Unboxing,June 2021
10:02
Rate This Smartphone Cooler Set-up ⭐
0:10
Shakeuptech
Рет қаралды 6 МЛН
Xiaomi SU-7 Max 2024 - Самый быстрый мобильник
32:11
Клубный сервис
Рет қаралды 542 М.
Samsung laughing on iPhone #techbyakram
0:12
Tech by Akram
Рет қаралды 6 МЛН
تجربة أغرب توصيلة شحن ضد القطع تماما
0:56
صدام العزي
Рет қаралды 63 МЛН