How to check canon image class power supply and repair step by step good condition full tutorial

Рет қаралды 15,485

TRC TECH

Жыл бұрын

Пікірлер: 48

@dipeshparmar8533 Жыл бұрын

Sir......nice information thank you

@thirunahariprabhakar6560 Ай бұрын

❤

@masterAadi2024 Жыл бұрын

Good

@sohailshaikh9207 7 ай бұрын

Sir I have canon printer. Output voltage on power supply is mentioned as 24V. But when checked with multimeter, it is showing 28.1V. Is power supply ok or damaged? Although printer is turning on. Printer's scanner motor is rotating fast in both forward and backward direction and then stopping suddenly. And also cis light is not turning on. Is high voltage a problem for both above issues?

@SONUSAINI-dg1ee Жыл бұрын

Cartege new dalne ke baad bhi print black aata hai... supply repir karne se phle ....earthing plate ko chrak jarur karle...

@trcteck Жыл бұрын

Depends upon the fault

@MuppallaSomeswaraRaoNani 11 ай бұрын

Hai..sir ..Canon mf4820d printer board automatic restarting problem & relay continuously making tik tik sound ..please help me with the solution

@chinnarao326 Жыл бұрын

Resp Sir! Canon MF244wd Printer Power Supply Series Lamp was On Sir all are LDRs, Capacitors, Bridge Rectify Diode, 3Pin Diode all are No Beep and No Values OK Sir. New FET was Changed Sir. 22G Ohm Resistor and 24G Ohm Resistor was Burned Sir (this Resistors 0.3 Values and Beep Sir) Where the Propblem Sir. Please Sir. I am Waiting Sir. -- ChinnaRao, Paderu, Visakhapatnam Dist, Andhrapradesh.

@allinonecreative9110 5 ай бұрын

Sir printer on nehi hu raha he😢problem kaise solve kare

@chinnarao326 11 ай бұрын

Resp Sir! Canon MF244DW Printer Power Supply DC 2.5V Ok But not Turned On Sir. Where the Problem Sir. Please Advise Sir. -- ChinnaRao Paderu Andhrapradesh

@trcteck 11 ай бұрын

Make sure it is ok or not then try

@chinnarao326 Жыл бұрын

Resp Sir! Same Canon Board Was K4005 FET Changed Sir and near 22G Ohms Resistor and near the Big Capacitor Resistor was Burned Sir. That Bellow 100Ohms Resistors 50Ohms 22Ohms was Installed but not Suported Sir. Same placed Jumper Suitable or not Sir. Please Advise Sir. -- ChinnaRao Paderu Visakhapatnam Andhrapradesh

@trcteck Жыл бұрын

Check primary section short component also check secondary section diode

@chinnarao326 Жыл бұрын

Resp Sir! Thank U Sir and not short the Primary Section Any Component Not Beep Sound Sir and Secondary Section also Same Sir. -- ChinnaRao Paderu Visakhapatnam Dist Andhrapradesh

@trcteck Жыл бұрын

Kindly share your ps card video on my Instagram id trctech

@chinnarao326 Жыл бұрын

@@trcteck Resp Sir! Thank Ur. OK

@trcteck Жыл бұрын

Most welcome

@chinnarao326 Жыл бұрын

Resp Sir! Same PCB output 3.7V Suitable Sir or Not Suitable Sir. 10 Ohm Resistor Replaced at Near the Big Capacitor and 1 Ohm Resistor was Replaced the FET Sir. Please Advise Sir. -- ChinnaRao, Paderu, Visakhapatnam Dist, Andhrapradesh.

@trcteck Жыл бұрын

Explain your problem with printer model no

@chinnarao326 Жыл бұрын

Sir Canon MF244WD Printer Scaner Sir. -- ChinnaRao

@trcteck Жыл бұрын

Replace logic card

@chinnarao326 Жыл бұрын

Resp Sir! Thak U Sir.

@trcteck Жыл бұрын

Welcome

@sandipgaikwad7314 Жыл бұрын

Solution kya he

@Heros228 11 ай бұрын

Always burn fuse.....pls help

@trcteck 11 ай бұрын

MOSFET and bridge change kro

@mehak6403 Жыл бұрын

Sir tray continuosly chll.rhi hai solution plz

@trcteck Жыл бұрын

Laser scanner change kro

@Amitfun606 Жыл бұрын

Power supply er r216 resistance colour code or value kaya hua

@Amitfun606 Жыл бұрын

Pls help me sir

@trcteck Жыл бұрын

Test according to colour code

@Amitfun606 Жыл бұрын

Pls help me sir ...r216 resistence burning and printer have no power

@Amitfun606 Жыл бұрын

Sir u not help me..pls r216 resistance ka value or color bolie....cause my power supply board me r216 resistance burning

@trcteck Жыл бұрын

Bhai mere Instagram par resistance ka photo bhej do instagram.com/trctech

@priyobrata2 Жыл бұрын

Sir board ka schematic diagram kaha se milega?

@trcteck Жыл бұрын

Part no?

@priyobrata2 Жыл бұрын

LBP 2900B

@sandipgaikwad7314 Жыл бұрын

Canon mf 4820 me blank print aa raha he

@trcteck Жыл бұрын

Replace power supply

@ShubhamKumar-bx8ps 11 ай бұрын

Sir Printer on ho kar band ho jata 3-4 second ke baad kya reason ho sakta hai

@trcteck 11 ай бұрын

Check fuser wala jha connector lga hota 8pm ki 3 leg ka MOSFET lga hota hai check kro

@ShubhamKumar-bx8ps 11 ай бұрын

@@trcteck fuse check karna hai power supply card mai ya mosfet??

@trcteck 11 ай бұрын

Both

@thirunahariprabhakar6560 10 ай бұрын

❤