My friend, you used a magnet to reposition the abs sensor screw. Those abs sensor usually work with either a magnetized inner bearing seal or a ring. Bringing another magnet near to the magnetized seal or ring can demagnetize them which will manifest as later as the abs sensor not able to determine if your wheel is turning or not. This can set off abs lights and traction control. Running an obd code will tell you abs sensor not picking up signal and if you replace sensor you will continue to experience issues not realizing it’s demagnetized bearing seal or wheel ring. Both replacement parts not too expensive but can be time consuming because you have to remove rotor and hub. Save yourself a big headache by simply avoiding bringing magnets near those bearing seals or rings. I’m just saying 😉

Very clear and helpful! Thanks so much!

Thank you for your presentation. No intro graphics, no blather. Straight to the how-to-do-it. Info, not ego. Awesome. Take note, others who post, this is how it should be! This is how you get followers.

Great video. Good lighting and clear pictures. Thank you!

Very knowledgeable, even though its not for my car what you explained really helped me what I needed to do qnd answered questions I had cheers!

If cleaning results in it not working do a resistance check on both sides. If you get no reading of ohms on one side it means it is open which is a broken circuit. If the other side say reads 3 M ohms or 5000 ohms or whatever it means the circuit is closed and the circuit is working... Replace the open sensor. If both sides read the same then you could have a problem with your tone ring or wheel bearing which has the the magnet built right into it OR no voltage issue which is another issue to deal with. you can turn your ignition on and check for voltage not on the sensor side but on the other side of the connector(not the sensor connector). Both sides should measure the same voltage say 12 volts or right around 5 volts. If no volts on both sides then you may have a blown fuse. If one side shows voltage and the other side shows nothing(0 volts) then you could have a broken wire. Then you look for broken wire and if that wire shows no break it could still be broke on the inside. Then you need to do a continuity test which is a resistance check for that wire. There is more but I'll stop here' The multimeter is the instrument in these cases. Votage ohms amps etc... is what multimeter is all about. If you don't know what you are doing take it to a back yard or good mechanic. You easily could get screwed on this. You can also get specific scan code readers for abs or airbag for these problems...Any way good luck

Thanks for this video. It is very informative and helpful

This was a really helpful video problem for me is I just booked it in with garage for tomorrow AM, wish I'd seen this b4, I could do this thanks to Kim🤔

thank you, this was helpful. I had just changed a rear hub on my Subaru and needed to tighten the master screw that holds the rear wheel. I wouldn't have observed this without getting after that rear sensor! Car running good again:-)

anything I can learn hands on,god bless,sir💯,

Thank you for this info!! I like what you doing make more videos! Bravo great job!

Oh ok, so that's where and how to clean them, Thanks a lot, i have subscribed to your channel . Thanks again.

Thanks, great video.

On some cars rust on the hub pushes the sensor out slightly which causes the abs to come on unexpectedly and intermittently. Remove the sensor, plug the hole so dirt does not get in (I have used the tip of a q tip) and clean the rust off the hub with some Emory cloth. Shop vac the hole then reinstall the sensor. A little light spray of white lithium grease will prevent the rust from coming back too fast.

Very useful. Good work

Thank you 👍✔️ Very helpful indeed.

Good job man I like your video

Help save a lot thanks good video

thnks for the video bro from Mauritius

Thanks very much for your help

Thanks for sharing this

I have same issue thanks for informative video

Explained in a very understandable way. thank you 🙏🌿 Please follow this friend

could my abs sensors be dirty ? few days ago the abs lights \ traction control lights\ brake lights came on... was on for a few days it was raining heavy when it came on... it stayed on for 2 days.... then one day it was very cold like 10-F then over night and next day the lights all gone.... the lights has not come back on.... will cleaning it resolve issue maybe ?

Quick question if I have a wheel whose tire is squeeking since my Trac off vsc off light came on after a bad snow do you think that's where the bad sensor is??? Thank you and I did subscribe and like...

very good. Thank you

If the dealer wants to replace the ABS module and hydrualic bump for an intermittant ABS light coming on then would you think it's best practice to clean or replace the sensors first then see if the issue is resolved? The module is pricey and the labor is as well.

In Ohio the rust belt this maintenance is required yearly Any way to spray on a protectant

I have ford explorer sports trac, my Abs was blinking. I don't used my car every day. But the ABS was light. What should I do sir? Can I change new replacement sensor or I need to clean the sensor? Really appreciated your response. Thanks

Thank you for sharing

Thank you for the information is very helpful , but my highlander 2006 is showing vsc and awd system also abs sensor how do I treat it

Nice video my friend

Thanks for the great video.

Once a year is planty or when u need pads

thank you bro

Good video thanks 👍👍

Thank you guy

Hej Kim, today I changed two tires (back tires) and now ABS/Traction/AWD signal lamp is on. Why is that?

How does the ABS light goes back off

Thanks !!

good job

Nice video

Ok I'm so thankful for you video got a shudder on braking pedal goes right down and bake right at the bottom could that be my censers or abs unit thanks

Thanks Dude

It’s mighty car mods Moog’s Swedish cousin 😂

Never seen one of these come out without breaking

what cause sound on the ABS pump?

I CLEANED REAR ABS SENSORS BOTH YESTERDAY, BUT IT TURNED ABS AND TRACTION LIGHT ON FOR THE FIRST TIME. CAN YOU TELL ME WHAT I MIGHT BE WRONG WITH ?

I good rain storm will clean them

Hi buddy my ford focus SE mk1 abs light comes on and off shall I do the same to my abs sensors

Besides cleaning the sensor, do you need to spray anything in hole to clean out anything in there?

goog job

Probably a good idea to check the reluctor ring while you have the sensor out, as they can corrode and crack.

But is it not a magnet ring on the axle too? If so can that be worn and replaced?

A dirty abs sensor can induce a limp mode?

Good video. I'd have appreciated it just a bit more thorough that's all.... like if I need to replace it.. then... how... cleaning it with what... if it needs replacing.... the cable as well? or can the sensor itself be replaced?.... any electronics resetting needed? My ABS light comes on... my tester says bad right front speed sensor.... but now I have to check more videos cause to take out a wheel takes a bit of effort and before doing that it would be nice to watch a video with all possibilities mentioned.... ✌

Line clear

I thought you were going to clean it. All you did was get your hands dirty!

I have the same type Volvo

Hello everyone is possible the abs light to be on because of a dirty sensor ?

you didnt actually clean the sensor like the heading says

❤

They put that sensor right where it will be difficult to remove if it gets stuck and they often do yours came out easy.

Is that already clean?

At 4:21 you throw the dirt back in the speed sensor reservoir 🤣.

Did the warning light remains?

Yes the sensor could be bad but most of the time it can be a indication of a wheel bearing starting to go bad or already KAPUT/ FUBAR

Its not that easy for kia. Ive had to drive them out from the under side because they hsve been too tight.Have damaged mounting ear trying to remove from top side.

My car steering gets hard when brakes are applied . Is that because of abs sensor

I would definitely use water and toothbrush to clean that sensor for sure

👍

I wonder if my 240 has those same sensors ?

First few seconds of this video and this guy is having people inhale brake dust

thank you can fixed my car?

best to just replace then clean.

Did the cleaning but abs light is still on (it comes and goes). What should I do next?

Sverige?

Just replace ALL 4-wheel sensors. For example, Ebay sells a 4-pack wheel sensor for a Toyota Tacoma for $18 with free shipping. the new parts are so low-cost ($4.50 each) it doesn't even make sense to mess with the old parts.

I cleaned all 4. But it's not working for me.

He told us to be careful then flicked the dirt into the area he just cleaned.

Abs light came on 1 day after it snowed I think the salt caused it to become dirty

nice volvo you got there, restore it.

For me its 10 mm

Duh duh duh 🙄

Jeeezus.. didn’t use any cleaner. Sucked i

Not going to lie this was painful to watch

👀

Great video, thanks