Do you have a differently method? I'd love to hear! Tell me below.

Toothpaste is an economical polishing compound, it even makes you smile after you use it. What a bright idea!

Just tried this on my sons track, he's over the moon. Much better.

Eh up mate, just bought and tried the AUTOSOL method for cleaning my very old scalextric track, Excellent results, thanks mate.

Great video. Keep up the good work 👍🏾

Great video Jack, I’m going to give Autosol a try!!

Save your fingertip, especially when doing large amounts of track. Use a short piece of wood dowling and wrap it in the microfiber then add your metal polish to it. You can press alittle harder without straining your fingertip.

I’ve used Solvol autosol since I was a teenager in the 70’s polishing my bike then polishing the Ali crankcase on my FS1E moped.

Great video, thanls for the tips and help

Bought some, tried it. It’s amazing stuff, cheers fella!

This Autosol product is very good. I haven't used it on scalextric track as I haven't had one set up for years, but it works a treat on push bike rims and also on magnesium car rims.

Very good I will try it

Awesome, thank you. Guess what I am doing this week-end?

I guess I'm hardcore :-) I used a sanding block, or a blade, or the front edge of a file. These are very old tracks which have probably never been cleaned before. The trick is to make sure that the connection points join properly. Clean them, bend them ever so slightly to make sure they have a good connection.

Cool

There is another brand called ‘peak’ Same stuff. But autosol is my go to anyway. But peak works too

I wonder if i could use on my outdoor railway ?

I had 50 meters of track to clean so I used a small 80 grit flapper wheel in a cheap dremel clone off eBay perfect results with no arm ache

Thanks for the great tips Jack, I'm going to try it as soon as I can get some solvol. But are scalextric tracks plated steel ?, would a peco track rubber damage the surface?, I'm sure the solvol won't, however the only track panels that are really bad here are some I bought on EBay and it looks as if some sort of plating is worn off. I tried the peco rubber but the groove ripped pieces off until we changed the technique. (I do know that some model rail track such as Hornby is plated and abrasives are not good for it, so its going to get some of your treatment too.).

Thk You Jack 💨🥇🤟

Is it a good idea to clean the black part of the track too? If so what do you recommend?

nice video helpful

Good tip, I thought I had auto sol metal polish, turns out it's auto glym. Still gonna give it a go though.

Just looked at the metal polish and it says it leaves an invisible coat of wax? Is that not good for the conductivity of the track to car?

One thing you got wrong. 9/1” it’s not rust. It’s a build up of carbon left behind from the electricity arcing

I have some autosol krome Glans can i use that or only metal polish?

Hi can hi use wd 40 thanks trevor

Probably the most frustrating type of toy to buy for a child.

Have you ever used copper grease on the ends of the track where the pins are? Some of my track is dirty in the ends and is hard to clean the pins so I’ve thought about putting a dab of copper slip on the pins to get good conductivity between two sections of track

white vinegar first on really blackened rails so much easier then do this. I have tried just this and got nowhere fast. lay kitchen roll or other cloth over track spray bottle of white vinegar soak down rails leave a few HRS and finish with your method. but my track was discussing

water ammonia combination baths .. place track in for 30 min ..ammonia is good for nickel cleaning ..( test one or 2 pieces of track first ) including mix ratio and time in bath ... if you hundreds of pieces of track coming out of storage like me rubbing with the finger or thumb with that amount of track is not the best

Interesting

I find it easier to just unclip and remove the rail, no damage or marks to the track that way.....takes a couple of minutes maximum.

Fanny juice is good for cleaning

Excellent! Thanks for this Jack. Bought a second hand set for my youngster and this will help greatly. Found that one or two LEDs had gone in the car lights too. Easy to change but so small!

Will this method work on classic track too?

Sounds simple to do BUT not when there’s so much scenery to be removed !!!!

Hello but, for,one,thing,one,piece of track yeah,easy, why,don't you do your layout, it,wont be easily done, epscaly,if, you have over, and, unders,,on,the,,layout