How to clear Fanuc 300 APC Alarm : A Axis need ZRN and 306 APC Alarm A Axis Battery Zero

Рет қаралды 17,190

Күн бұрын

Anytime you disconnect a servo motor encoder cable you will get this alarm, this happens to be the turret. You will get this when the battery goes dead as well. The battery only stores the encoder value, that's all.
This video shows how to change 1815.4 APZ when the turret is in the correct position and clamped up. This particular turret home station is tool position 12, or the highest number of tool stations, not station one as I stated in the video. I had to redo this procedure as the turret was one station off.
The link below is how to do the same basic procedure with a z-axis on a lathe.
• Reset Z-axis after tri...

Пікірлер: 22

@nx2.0ng71 Күн бұрын

Thanks a lot Daryl, from Canada !

@AlexdeBruijn Жыл бұрын

This video couldn't be better. It workt perfectly with the X and Z axis alarm on my Schaublin 125 CCN (Series 20-T). Thanks a lot👍🏻💪🏻

@MeisterDemant Жыл бұрын

Thanks a million from Germany

@arooshhulawale5865 Жыл бұрын

I did the same procedure but my program doesn’t run after it reaches the tool changing program

@OtherBrotherDarylSmith Жыл бұрын

There is no tool change program. Close the door, go to MDI mode and call up a tool. T0101; and then insert, hit cycle start. If it doesn't move to tool #1 you should get a message. What messages or alarms are you getting?

@simplyme6748 8 ай бұрын

Damn I couldn’t really hear that well and I accidentally hit the input when you said not too ! 😮what do I do in this situation

@OtherBrotherDarylSmith 8 ай бұрын

You need to change that parameter back to your original parameter. Let me know what machine model, serial number, and which parameter. I might have a backup.

@OtherBrotherDarylSmith 8 ай бұрын

Don't run the machine if you changed the first parameter. It could crash if you changed it from metric to inches.

@OtherBrotherDarylSmith 8 ай бұрын

If you have a hard copy of your original parameters, just put it back the way it came from the factory. This is why it is important to have a backup of your machines.

@abramfriesen9834 Жыл бұрын

Hello I have a Hardinge cobra 65 like to know how to us the Fanuc 21-t controller and dost it have a home button I can move the Z and the X just can't find the home swich

@OtherBrotherDarylSmith Жыл бұрын

That machine uses what is called an "Operator's Panel". You can hit the "Quick Page" to find it, then page down to find the "reference" button. If you don't have a "Quick Page" button, hit the "offset" button, then the right expansion key, and then "OPRT" soft key to access the "Operators Panel". The first page is usually blank, so page down. That machine also uses APC/APZ, so you can refer to my video on resetting the z-axis torque limiter if you need to reset the home positions.. I can also send you some PDF files if you send me an email.

@OtherBrotherDarylSmith Жыл бұрын

The 21T and 18T are very similar as far as the parameters. The difference is that the Cobra uses the "Operator Panel" internal switches instead of selector switches.

@ER-zv1nr Жыл бұрын

I could really use some one on one assistance. Where did you learn all this ?

@OtherBrotherDarylSmith Жыл бұрын

Pretty much I learned on the job, the hard way. I have never had any training. I have read a lot of machine manuals. Documentation is priceless. I have also had some co-workers who helped me along the way. That is why I give e back.

@OtherBrotherDarylSmith Жыл бұрын

My co-workers called me a "button pusher" when I I started out 30 some years ago. I would ask them, "what does this button do?". If they didn't tell me not to hit it, I hit it. There wasn't a button on a control I didn't push, lol. It got me in trouble once, but I learned to be more careful.

@fredrezfield1629 9 ай бұрын

hey not sure about your CNC but on the DMG there is no HOME or referencing in X or Y or Z ; its supposed to know where the mill is whenever you start up. so ,what do i do if i am "0" in APZ "x" and APZ "Y" ( my batteries died i had to replace them) how do i "return" X or Y ?

@OtherBrotherDarylSmith 9 ай бұрын

What machine model and control? I have worked on lot of Mori Seiki machines. Is this a mill or a lathe? I can send you a procedure. Where are you located?

@OtherBrotherDarylSmith 9 ай бұрын

You shut it off after getting the battery alarm. All the batteries do is store the machine's position when power is off.

@fredrezfield1629 9 ай бұрын

@@OtherBrotherDarylSmith DMG DMC CNC mill deckel maho i am in london ontario canada thanks

@fredrezfield1629 9 ай бұрын

sorry i thought that was a question? i always thought you'd change batteries with the control on that's what i did but the DC0300 alarm messages for Return X and Y wouldn't go away

@OtherBrotherDarylSmith 9 ай бұрын

@@fredrezfield1629 What control? DMG has their own numbers, but I am assuming it's a Fanuc with a DMG number.