How to connect your Trimble GNSS Receiver to your DJI Drone

No video

How to connect your Trimble GNSS Receiver to your DJI Drone

Рет қаралды 3,298

Harry Macpherson-Wood

Күн бұрын

This video explains the process to receive RTK corrections for your DJI drone by connecting your Trimble GNSS receiver.

Пікірлер: 18

@stuartross1081 5 ай бұрын

Thankyou very much for that for that. I appreciate it takes a lot of effort to assemble a video like this. I have a similar workflow. However, I typically set up my base first thing to allow me to do conventional RTK work , road edges hatches, and so on with another pole mounted receiver. (which provides valuable check points later). I will get my true base station position doing a short session of VRS or RTX then use that position to start it as a base. I don't use "Here point" anymore as it took too long to sort out afterwards. The issue I have run into is that the moment you configure the R10 as a base with Trimble Access and start transmitting corrections that 3.2 setting is lost. It is possible to link to the base with a browseer while it is already transmitting a radio correction and reset it to 3.2 again. Its clever, in that it retains the coordinate, antenna height and radio correction. If youu have colleagues working up the hill from you on RTK rovers you don't disrupt them. The correction from the R10 to DJI is really strong and solid in my experience and those check points on hatches and the like bear this out. I've had astonishly good results. I noted you were over writing the VRS RTK settings in DJI to accepr R10 instead. I found this a nuisance if regularly jumping between the two and kept a laminated printed sheet with respective settings in the box. To their credit DJI have fixed this now and you can save each profile with a name and select it as you desire. I do like the VRS when the site is favoured with phone signal as you can fly the drone as long as you have your hotspot phone in your pocket (Much lighter and less restrictive than carrying an R10 across the mountain side). I thought you may find this of interest.

@harrymacpherson-wood 5 ай бұрын

Thank you @stuartross1081, much appreciated. A few good comments there.

@HG-Reality-Capture 4 ай бұрын

Kia ora! Great video from Harry and a great comment from you. Something I have noticed, which ties into your comment. If I set my base over a known Co-ordinate and start the base in Trimble Access, it auto populates the reference station. I find using lat long a pain as we work so much in NEZ. Could you confirm your workflow aligns with mine. 1, Set up base over a known Co-ordinate 2, Through Trimble Access, select Measure, RTK, select control point, Start base. 3, Connect to Web GUI via controller, update the RTCM to be 3.x (seems to change back to 2 automatically) 4, Ensure RTK connection and fly away? John.

@harrymacpherson-wood 4 ай бұрын

@@HG-Reality-Capture That's a really handy tip, thank you. Next time we setup using a base station I will see if it connects as per your process mentioned. When we have control points in Trimble Access, we normally change the settings to represent lat and long. Definitely would be a good idea if we could leave it to our preferred Easting Northing. Thanks for commenting

@stuartross1081 3 ай бұрын

@@HG-Reality-CaptureI have read your notes through and I think our work flow is identical. I get good support from our Trimble dealer here in Scotland. Each time you use Access to configure base it resets that 3.x. If you use e, n, h as long as your transformation parameters are correct it will broadcast correct late long ht to feed drone. I always have check points scattered across site to check for blunders but I find R10 correction is better than VRS but this is the same for conventional pole work.

@harrymacpherson-wood 7 ай бұрын

Not through the DJI controller. As far as I am aware you can only record your photo positions using RTK. If you want to further post process you can use third party software; for example LiDAR post processing to update the image file locations. Is that what you were asking?

@rapturemusicartist9348 7 ай бұрын

I’m looking to create a RINEX file to use in a third party software, if I can extract static base data to create tighter data that would be great.

@rapturemusicartist9348 7 ай бұрын

How do you find out the password to your static rover??

@rapturemusicartist9348 7 ай бұрын

Mine says Trimble GNSS 7734

@harrymacpherson-wood 7 ай бұрын

@@rapturemusicartist9348 If you use the same details as what I have said in the video this should do it. This should be the deafult password

@harrymacpherson-wood 7 ай бұрын

@@rapturemusicartist9348 Because the rover does not record the data but the controller does. The only way I see you being able to record a RINEX project is through the Trimble controller (meaning you treat your flight not as an RTK but PPK mission). You can export job files in the Trimble controller to get RINEX files.

@eprohoda 7 ай бұрын

greetings!Harry- professional , ✋

@MaryKule 4 ай бұрын

Hey Harry! Could you please elaborate on what you mean by "block shifting to an absolute location" if you are not near a known benchmark? Thanks!!

@harrymacpherson-wood 3 ай бұрын

Hi Mary, Block shifting would be where you treat you data as a single piece and shift / move / scale (but not contort, or twist) to survey ground control points placed on the ground. If you don't have surveyed ground control points you won't be able to block shift it to a datum. Does this help? Thanks, Harry

@MaryKule 3 ай бұрын

@@harrymacpherson-wood Yes, thanks so much!

@rapturemusicartist9348 7 ай бұрын

Can you create a base file, for post processing?

@santhanakrishnan8632 5 ай бұрын

I have try to access the webpage, the username and password is invalid. How can i access the webpage

@harrymacpherson-wood 5 ай бұрын

If you have the GNSS unit turned on and have not changed the standard settings it should all be as per the video. Unless you have a GNSS rover which isn't base compatible?