How to Convert a Halogen Floodlight with 50W LED at home

Рет қаралды 30,272

3 жыл бұрын

How to convert halogen floodlight with led chip 50w that works on AC220 directly without power modeule,all electronics its on board.
I got mine 50w led cob chip from aliexpress:www.aliexpress.com/item/40009...

Пікірлер: 41

@mlefe09 3 жыл бұрын

I feel like the cable should include earth and that wire should be attached to the metal frame... if the live wire dettaches from the PCB (with heat and no clamps that's possible) you may end up with a lamp connected to the live wire...

@motivasidanilmu Жыл бұрын

I think the light will only turn on briefly and then die in less than 1 hour due to overheating because the heat is not distributed properly because epoxy glue is not a good heat distributor

@psvyme48paulh45 3 жыл бұрын

How can you test 3v CR2025 Battery like a watch battery, can change it as well

@ushaninilanka7342 3 жыл бұрын

oh noo thanks for the video.....waiting for your next video........big fan from sri lanka

@mahasun2125 3 жыл бұрын

What is the heat transfer coefficient of epoxy resin? There's gotta be a problem with the heat release of heat.

@moya9450 3 жыл бұрын

Exactly

@ggesdsdsdsd 2 жыл бұрын

True, he could of used themal glue off ebay for like 3$

@electronic7979 3 жыл бұрын

Excellent project 👏

@kishorevenugopal6191 Жыл бұрын

Is that illumination worth 50 Watts?

@jagathisvimal1129 3 жыл бұрын

Cool.

@user-wu9sy5vn3l 4 ай бұрын

Very nice bro

@Hacktuber 4 ай бұрын

Thanks

@Fred_Zepplin 3 жыл бұрын

I Did The Same Thing with A Tractor Light & A Dollar Store Flash Light.. I Wanted A Vintage Looking Bullet Light And Got The Tractor Light for $8.99 and The Flash Light That Takes 4 Double A Batteries With The Silicone LED .. Anyway I Just Power It With An 18650 Battery (from A Dollar Store Power Bank.. I Left The Charger Complete and Just Soldered The Wires Into The Pos/Neg on The Battery.. So I Could Charge It With The USB.. I Carry A Couple More of Those Powerbanks in My Tool Kit).. It's A Motorized Chopper Bicycle With A 100cc Bike Engine on It That I Built Years Ago.. And Just Love It.. No Plates/Ins./Etc. .. Just 16 & A Helmet (where Helmet Laws Are Enforced).. And About 100 miles per Gallon.. and 2 stroke oil.. About 20:1 and They Go Pretty Good.. Mine Will Do Just Over 60mph.. Although, Some Places Treat Them with E-Bike Limits of 25mph..I Think?.. Close Anyway.. I Do That In Most Places Anyway... But, On An Open Stretch Of Back Road.. Let'er Rip!!! lol.

@manp1039 3 жыл бұрын

have you figured out a good way to reduce the decibel levels of the engine? I was considering using a gas-powered motor assist to bicycle, but don't want it to be so loud.

@zumbazumba1 3 жыл бұрын

The whole body of a floodlight is made of an aluminum -why not just mount led chip directly to it so it can be used as a heatsink?

@dhrubojyotighosh9592 3 жыл бұрын

That aluminum body is too thin to be used as an external heatsink and that LED Chip can get REALLY HOT that the aluminum body cannot dissipate and therefore, it would just be a blown LED lamp

@manp1039 3 жыл бұрын

I was thinking he would mount the Heatsink to the rear of the lamp. however, it looks like the lED chip was a bit too wide to mount flat to the rear of the aluminum lamp body. Although it looks like he could have shaved away portions of the LED board while preserving its electronics and then mount it to the rear of the lamp body with some thermal paste and the heatsink to the back of the lamp?

@ggesdsdsdsd 2 жыл бұрын

@@dhrubojyotighosh9592 Could still put the heatsink on the outside...

@milenkovasic9070 6 ай бұрын

Where is ground wire?

@psvyme48paulh45 3 жыл бұрын

Nice 👍

@Lukaszmajamen Жыл бұрын

Jak rozebrać klejony reflektor LED? How to dismantle a glued LED headlight?

@youtubehelpsupports 3 жыл бұрын

dislike for gluing the led chip heatsick with epoxy! the thermal paste had to be used and then fixed with 2 screws. it will burn soon.

@adnancaprio 3 жыл бұрын

this will blow up very quickly since you used epoxy instead of thermal paste so the heat transfer will be very bad plus there is no active cooling

@user-hj6df3jf4w 6 ай бұрын

Yes true, he could of put thermal paste in the middle, then used the epoxy on the sides to secure it down to the heatsink.

@MiamiMillionaire 3 жыл бұрын

👍

@MdAlim-cz2yz 3 жыл бұрын

Bro ur mic is to sensitive Pls fix it

@joseorellanaorellana8476 Жыл бұрын

Buenicimo

@_munna_ 3 жыл бұрын

👌👌👌👌👌

@ericklein5097 Жыл бұрын

I don't think epoxy is going to be very thermally conductive

@elgatodecafe4725 2 жыл бұрын

SMD LED chip is more eficcient

@joseorellanaorellana8476 Жыл бұрын

Que cambio

@Reposted3000 3 жыл бұрын

First

@robertofreitas8825 2 жыл бұрын

Just change the lamp

@geezer4444 Жыл бұрын

you have to be joking with that setup using glue as a heat sink paste or connecting to the heatsink?????? you must be crazy but you sanded the heat sink creating more air pockets i hope you dont EVER work on my fixes

@1marcelfilms 5 ай бұрын

That chip will die in a few weeks or months. Even a 10w led would overheat in there

@Drooon67 3 жыл бұрын

Охолодження мало! і нарешті ці модулі повне гівно вони працюють малий термін!

@dayak1238 4 ай бұрын

defend only 4 days 😂

@tonywharton5220 3 жыл бұрын

The sound on this video is terrible. Makes it unwatchable.

@jaya2458 Жыл бұрын

I think the light will only turn on briefly and then die in less than 1 hour due to overheating because the heat is not distributed properly because epoxy glue is not a good heat distributor