Very very helpful. Probably one of the best training videos be seen. As a disabled vet fixing to start life on a very small fixed income some friends recommended I start to enjoy my hobby of woodworking (with toys for my grand kids and such) and expand into making patriotic things for fellow service members and vets (my son has been in 10 years and 5th generation navy so hopefully he’s a good salesman lol). With the exception of material and a little for overhead I’m hoping I can make the bills and instill a little honor and patriotism back into this great land of ours. Just learning but you have helped me tremendously with your instructions. I hope I’m able to pass it on to those I’m able to creat something for. Again. This Texan and Navy vet tips his hat to you sir. Wish I could do more, and perhaps I can someday. Thank you.

gostei muito da sua aula , muito bem explicada obrigado!!!!!!

Wow... I thought I was finally reaching a medium level user in Aspire. Thanks for putting my ego in check. I absolutely love this video. I know it is a lot of work to put these together, so thank you for your time and effort. You now have a new subscriber.

Excellent training video! The ever-popular waving flag is a great subject for learning Aspire. Learned about a million and six new tools and ways to use them. You did a super job of showing the tools as you used them. Keep telling us noobs every key that you're touching, even the basic and obvious ones. Very good instruction - many thanks from your newest subscriber!

Great video. There's a lot to digest in this and it is pretty straight forward. I haven't gotten all the way thru the training yet, but one issue came up I was having a problem with around the 20 minute mark. In doing the baking of the duplicated level at that point, my version of Aspire 10 you can't bake a grouped set of components. They have to be ungrouped and I found that if you hold the Crtl key when baking it creates a level of unbaked components automatically. I was trying hard to see what you had done and I reverted to searching for the reason I couldn't get this to work right. At any rate, you have done a great job of providing instructions that make using.

Excellent tutorial. Clear instructions. Made a complex project doable. Thanks!

Excellent tutorial Laney!

This is one of the best videos I have ever seen. You rock dude!

Great video. Worth the 1 hour of my life. I learned more than I though I would, great job! Liked and subscribed.

Wow, I'm glad that I found your channel. Very clear instructions and easy to follow. Great that you show more that one options. I will have a look at your other videos :) Thanks

Wow man, absolutely great video. THANK YOU!

Laney, Thanks you so much for sharing this video. This has been extremely helpful to me as a new user of Aspire & CNC.

Excellent tutorial, thank you!

Thanks Laney - awesome tutorial!

Great video....you really have aspire down.....I made a flag off your instruction...Good stuff!!

Great video. I am brand new so bare with me on this comment. I believe the inner radius percentage should be 38 and not 40. If you zoom way in on the star the star is not perfectly flat across it has a very slight wave in the line. Very minor and I am not sure yet if it will show on the carve.

Very good video . Great job . Thank you very much . I learned a lot

This is a great video and so helpful and inspiring to do different things BUT you missed 1 huge step that I can not get passed. I noticed it has happened on your project as well but you skipped it. At time 20:42 exactly when you baked the project it inverted it WHY????? and how do you get out of it??? The next sec you had already fixed the issue and moved on UPDATE: I did wind up fixing this but I am a little confused as to why it did what it did. Some how it took the last in the components and used it (stripes) as the baked properties and it named the file that. Very confusing. This is still a very helpful vid!!! Keep going we need you!!

Very good video, thank you.

Fantastic tutorial, I followed step by step, sadly I couldn’t do the ripple effect because I don’t have the vectors for the sweep, pleas can anyone advice how that is done

Great tutorial! Do you have one on making a flag without the wave?

Great tutorial !!!!!! thanks alan

Outstanding tutorial on making a flag! I followed it step by step and turned out great! How did you convert the Navy seal to a 3d component. I can't get any I find to have good detail. do you have a video on that ?

on the modeling i dont have some of the components on my Vcarve pro 11?

I have a simple question concerning milling. If I am cutting with Inside Left does the 0,0,0 datum preserve the offset of the bit diam or is the 0,0,0 position dead center of the bit and then when routing the offset then takes effect? A simpler execution statement would be: bit starts out dead center on datum point then offset takes effect when cutting. I need a precision cut done but am not sure how the cutting offset is put in place. Trying not to waste material. Thanks.

How long was your carve time? Would you mind doing a video for speeding up toolpath times?

Great job and clear instructions. I was doing really good until the "baking" whereupon my stars went from protruding to recessing. Any ideas as to why? Thanks for a fine video.

No other way than to subscribe!

very cool, thanks

2 Questions: 1) Can this be done in Vcarve Pro or do you have to have Aspire? 2) How long would it take the CNC to create the wave flag with logo?

Wow!! nice video. Where can I get the Navy logo?

Hello, i'm new to cnc, just wanted to ask do i need to purchase mach3 to operate the cnc or vectric aspire does it all ?

I am using the trial Aspire download to see if I can do this. I was tracking with you all the way until you got to "Lets add a wave" and you selected a drop down from the top screen of your 2D called stars stripes 2 (at around 22:00 in the video.) My question is do the ripple waves 1, 2, 3, and 4 come with the Aspire software or are those features you previously created. I don't know if those features are missing because I am using a trial Aspire or if those are your personal creations. Please advise, thanks!

Does anyone know if I were to put and object on the flag and wanted it flat how would I go about it?

That was great. I wish the file was available to make it easier to follow your instructions.

Great tutorial. Thank you. How did you get your measurements, and how would I go about scaling them up?

Love the tutorial, Any way I could purchase a copy of the file? new to aspire and feel a little overwhelmed.

I have one question what kind of computer are process are you running because mine's dragging. A--

I'm a complete Novice here, where do the ripple and wave layers come from?

Not sure if anyone will still see this years later. Will this work with my Vectric Desk Top? I realize my size limits.

Why dont I have those options in my modeling tab?!

Can you do this same project in Vectric Vcarve Pro ??

Can this be create on V carve Desktop?

The star field is not square. You need to get the correct proportions.

This time I will use Woodglut plans for this.

Excellent sir can you send me your email

how do i get in your Facebook Group