I have problems getting my grips flush because I have alot of reverse pitch. I used to just try and force it and it never worked right. After watching this video, I couldn't wait to try doing it this way. It worked great and I'll never do it any other way again. I love how it turned out.
@bosoares Жыл бұрын
omg, can't wait to try this. I've done similar steps but not quite the same and never had the results you're showing. I hate how my inserts either stick out of the ball or I'm left with jagged and sharp edges. This might be just what I needed. Thanks
@enigmazero8624 Жыл бұрын
This is amazing. I am blown away by how good the finished product looks. I have always hated cutting grips and just dealt with distorting them by forcing them in and gluing. Of course I just recently changed to not using grips at all, so I can’t even try this anymore, but I still appreciate that such a technique exists.
@BobsWoodStuff Жыл бұрын
Really great info here. I may start drilling my own balls soon on the drill press, so this is very helpful.
@alexadams1627 Жыл бұрын
Great tip. I just butchered my inserts today so hopefully I can smooth them out with some acetone.
@DG_Haus6 ай бұрын
My pro shop left the grips sticking out so high, it was really annoying me. This is perfect, got them flush. Thank you!
@gtbinh Жыл бұрын
Great tip! Love these type of tips content
@thehappyextruder7178 Жыл бұрын
Excellent video thank you for sharing your techniques.
@sparkplugpeggy49107 ай бұрын
I use nail polish remover and a qtip after trimming and it worked amazingly
@TraumaRider Жыл бұрын
Very cool! I will practice this on my old ball
@jonmayer Жыл бұрын
I need to try this on my ball. very cool.
@mpawli10 Жыл бұрын
Awesome !! Thank you for this.. can't wait to try it
@randy181712 күн бұрын
Good stuff. I just had inserts put in. They're a little too deep. The inside edge of the drilled portion of the ball has an edge on it. How do I put a bevel on the fingertip holes without removing the inserts?
@LookMaa2Hands Жыл бұрын
I love this. It’s been a problem for me for a while no and I think this solved it!
@dennisbeck2521 Жыл бұрын
Fantastic attention to detail. Thank you for sharing your knowledge. The biggest issue that I have in regards to inserts is; I use vise semi-power-lift inserts. Trimming them removes part of the "lift" portion of the grip. It seems as though the options are: let then stick out a bit and hope that no one notices, or, insert them deep enough so that they don't stick out, or, stop using power-lift inserts. What would you recommend?
@Nulookproshopbowling Жыл бұрын
What are your pitches?
@tylerjones2559 Жыл бұрын
I just switched from these exact grips to ovals and I’ll never go back. Try the ovals if you haven’t already. They feel natural and you’ll be able to use this cutting method as a bonus.
@Nulookproshopbowling Жыл бұрын
@@tylerjones2559 I use the Oval/Power Oval from Vise, love them!
@marshallhummel8590 Жыл бұрын
Thank you!!!!
@wms702 Жыл бұрын
good tip.
@bowlingxp8345 Жыл бұрын
I wac using the same cutting method but without the ball cleaner and acetone. Genius ! Thanks ! Can the acetone alone be enough for the inside part of the grips in case we don't have a surgical type blade ?
@Nulookproshopbowling Жыл бұрын
It will soften the edge a little but an exacto knife just barely taking a sliver off the edge makes it better and faster. You can get them at any hobby store or arts store.
@bowlingxp8345 Жыл бұрын
@@Nulookproshopbowling Thank you ! I also subscribed just because of this video. Well made ! (i think you might like mine too ;) )
@t.hargrove3843 Жыл бұрын
Nice technique, but I have a question for you. Are you using the xacto knife on the inside edge of the grip where your finger goes, or on the outside edge of the grip where it touches the ball? It's hard to tell from the camera angle. Thanks.
@Nulookproshopbowling Жыл бұрын
On the inside edge where your finger goes, just to barely break the edge. The you will use the Acetone after that.
@5fiftyshack-2726 ай бұрын
Can you do this process with lift grips/pillows?
@chadhauser636 ай бұрын
You can just depends on how strong the pitches are.
@rondambrosio9967 Жыл бұрын
Do you have a technique for the clear vise grips? They seem to be really tough to cut smooth.
@Nulookproshopbowling Жыл бұрын
They should cut the same way. Just make sure you’re lubricating the blade with the ball cleaner and you’re using a brand new blade and when you cut it make sure you’re cutting in a slicing type motion, and so your pulling the blade towards you and not towards the grip. Hope that makes sense.
@brandonferris893410 ай бұрын
Can you tell me what kind or size of razor blade that is? I'm having a hard time find something like that. Thank you.
@Nulookproshopbowling10 ай бұрын
It’s a standard 1” wide razor blade from Home Depot. Then get an exact knife.
@HUFF-N-PUFF-2024 Жыл бұрын
What kind of glue should I use to install inserts
@Nulookproshopbowling Жыл бұрын
I use VISE insert glue. Don’t use regular crazy glue from Home Depot or department stores.
@dukea1 Жыл бұрын
What exact blade part#/ name? Thanks.
@Nulookproshopbowling Жыл бұрын
Any EXACTO blade from a craft or Hobby Store. The bigger blade for cutting them is from Home Depot.
@h20dept123 Жыл бұрын
@@Nulookproshopbowling Many thanks! And thanks for your invaluable tips!
@reyngel Жыл бұрын
@@Nulookproshopbowling What kind of blade is it? Just so I know where to look at Home Depot
I myself am 3/4 left and 1/2” reverse and 0 and 1/2” reverse in ring finger. I have also done some for Belmo and he is 1” reverse.
@bobjanicki9045 Жыл бұрын
Why would you cut the grip just put upper side in first then glue that side then pull up the other side and glue its easier
@Nulookproshopbowling Жыл бұрын
Because you are distorting the natural position of the insert which does also change the size. To each there own, this is just another alternative, especially with vacu grips when you only glue the top front side.