I had thought of this method when creating spiral threads was always misaligned (not straight). Thank you.

I can never unhear this music life is over

Was going to use E-clip for a 3/4 inch steel rod. Making my own Woodworking bench vice. With this tip, I just might make one for each of dyes, stamp, anodize and make their own case. Awesome setup 👍.

Nice guide but you will need to insert bushings in the aluminum block or use a different one for each thread size.

Wow, I'm having that exact problem threading 10mm rod right now. I will definitely put this tip to work tomorrow. Thanks

GOD BLESS you sir! You may have just saved my tractor because I must make a stud for the engine to save it since the studs are DISCONTINUED. THANKS SO MUCH.

I wonder if a hardwood block would work instead of aluminum? I have a lot of maple laying around so Ima give it a go.

Great tutorial. I have to cut an unusual thread for an older saw and want it to be straight.Thank you.

Drunken threads, make a 30 deg chamfer on the rod end, turn the die over so the chamfer reduces the cutting load and so makes it easier to control the start and check with a square.

Great idea, but face the stock with the shoulder to the back. That way you prevent the die coming out and the shoulder will take the pressure.

ADAPTOR ¡¡Excelente idea...!! --- Muchas gracias por compartirnos tan buena idea. Felicidades.

While this device dedicated to one diameter only (unless bushed for smaller) works it does present several drawbacks. It requires the die stock to be weakened! Holes drilled. It requires a long length in order to be self guiding! The block can be smaller. It is bulky and cumbersome! Limited ways to reduce this aspect. There are die stocks (Quality) that have an adjustable dia self guiding mechanism built into them that is compact, requires only a twist of a ring and thumb screw tightened. If you are going to be doing a lot of this I suggest the quality tooling route. John.

Great tip I've been troubling over this for weeks. Cutting 2 threads in 1/2 inch SS, 1 UNC the other UNF. Both fail. I can make this work for me. Thanks heaps

the same thing would also work without the die in backwards, possibly ...?

obviously works good, and would be great for production work but a lot of effort for the weekender or multiple sizes

This is a great idea to tread a crank shaft on a predator 22hp motor and keep it straight

question can I use it to repair damage thread?

So you have to make one for each die? Sounds like more work than i want to do, but thanks. I enjoy watching someone being creative.

Great idea if you make a 2.0 you could make the block larger and bore the hole to an inch and make bushings for all of your dye sizes so it will work or more than just that dye size now you just need a tap one as well

It definitely does the job! Would be better with replaceable inserts for different diameter rods though. For my purposes, just playing around with RC cars, it's usually enough to put a little spirit level on the tool and try and get it straight at the start before the tool has fully bitten, there's a small window of opportunity to make corrections. Not exact by any means but good enough for basic uses.

Just drill one side of your die holder and bolt on an inch by an inch right angle piece of ali. Slot the ali to accommodate all sizes of rod to be threaded so it can be slid to the side of the rod and bolted down tight to the holder. When you start cutting, keep the downward piece of ali against the rod. A guaranteed true 90 degree cut every time on all sizes of rod. To make it even better, drill both sides of the die holder like in this video and use 2 right angle pieces of ali...👍

Wow! That's cool, thank You for uploading!

Nice thinking

This is a great idea finally someone with a brain thanks

А если на короткой шпильке нарезать ? то как сделать?

What happens if you don’t have a threaded bolt to start from? I’m about to do a weird size, M22x2.0

with a different diameter pin you have to do another piece.

Simple drill bushing formula is bushing length = 2X work diameter, anything longer does not contribute to greater accuracy, i.e. a 4 mm diameter will only need an 8 mm long guide bushing for maintaining 90 degree perpendicularity.

Pretty cool. Great job.

ADAPTOR, nice trick. I ended up using a drill guide block---one of those cheap plastic blocks with steel guides. Was able to thread a 3/8 rod about 2" without problem

Good idea,good tool,easy to used .not running, stables.easy to handle.

Very good idea! You will need to make a jig for each tread size.

Brilliant!

thanks for share!Nice

this works only for long screws,not short ones

show inner die how make various stair.also show inner stair

The die is facing the wrong way, the starting cut thread on the side of the die should be facing towards the item your cutting

Love your idea

Cool idea. But you would need to create a different block for each die right?

Perfect solution.

This is good!

I do not like half hearted praise.This video is simply brilliant if you do not have a lathe.Well done and thankyou very much.You have been most helpful and I really do appreciate you taking the time to post.BRAVO!!!

Alright, I made this too but with a drill press and I got a good result putting an M8x1.25 thread on a rod. I made it with M3 rod. Be careful though when drilling the 3mm holes and you can see there is an uneven surface. But as this die holder is aluminum, it's easy to file away the edges to have a flat surface for drilling.

is there anything like this for sale on amazon ebay?

What if you're threading a short bolt.?

Dude that is.....¡¡¡GENIUS!!!!

"There is nothing pleasant abandoning protection provided by dreams and hope"

hand drilling guide holes? what if they are not all aligned?

Hell of of a good idea 💡

This is mind blowing! extra weight keep the balance and from damage.

Very good job

Can you make a CNC threaded rod would those things Can th You have a really good design for it at be made for accuracy

good idea

ingenious! Making one today.

only drawback: the rod to be threaded must have enough length to accept the device. Clever however

thanks for this information

nice solution

Neat!

Amazing solution! Thanks a lot

great job explains everything I did not know.

👍🏻

Yes Good Idea

Awesome!!!!

Ap Jo hath se gumate ho vo device muje by karna he ye kaha milega. Usaka name kya he.please reply

Good job .

Super Video! Like,Like,Like!

you used some type of grease instead of a fluid. what was it?

cool idea,tnx😀

This project is very good!

ESPECTACULAR!!!!

Nice

Bel colpo, si vede che sei del mestiere. Complimenti.

Nice one dude..👍👍

Cool

I want to see this done with SS Round Rod

So nice idea

Nice work! Very helpful video. Thank you.

👍

well is an old vid but i had to imput an observation..The dia holder opening should be facing the block..ie the work.its designed so the dia won't push out of the holder...cheers..

how do you know the die is true. but to be fair not bad jig for amateurs use

Great idea

186 people didn't watch the last half of the video... Awesome.

What is the name of that tool

So simple, very clever

Now all I have to do is play this music to make aligned threads.

Great video.

clever

from Iraq well done

Nice very nice

Smart idea 💡

Good Boy! Very clever

Who else muted after 10 seconds?

Very intelligent idea

good idea ! like !

Good Idea!

Everyone complaining about the music and hear I was grooving the whole time.

Best....

GOOD IDEA !!!!!!!!!

Super

Owesome technique but u can thred only one size with this tool pls make an udjustable tool that fit on any size