How to Delete Torque Management 99-04 Jeep Grand Cherokee

Рет қаралды 28,590

Күн бұрын

I'll show you a couple different ways to delete Torque Management to give you a quicker and trimmer shift especially noticeable at full throttle shifts from 1st to 2nd and 2nd to 3rd gears.
Amazon Affiliate
Thumb Wheel Ratchet Wrench amzn.to/37RiLQI
Precision Mini Screwdriver Set amzn.to/31PKy0k
Dual Wall Adhesive Heat Shrink Tubing amzn.to/2TyW5fR
Wire Loom Tubing amzn.to/2TBlsNY
Electric Tape amzn.to/3kDXMnX
Toggle and Rocker Switches amzn.to/2HzIz9x
Donate to Help Support Channel www.paypal.com/cgi-bin/webscr...
Facebook / martinbuilt-2351766611...
Disclaimer:
FYI if you click any of the product links above and end up purchasing anything I MAY get paid a small commission at no extra charge. This is one of the ways you can support the channel. Your support helps me bring out more content for all of you. Martinbuilt assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from the information contained in this video is the sole responsibility of the user and not Martinbuilt. Martinbuilt cannot guarantee against improper use or unauthorized modifications of this information.
#martinbuilt #jeepgrandcherokee

Пікірлер: 268

@bolt_husky 3 жыл бұрын

Did this 8 years ago in my 02 4.7 HO. It’ll chirp tires on the 1-2 shift haha. Everyone thinking this hurts and does harm and blah blah have never worked on a vehicle, probably have a piece of paper with ASE written all over it and probably own tools from a white service truck with red letters on it. Slip creates heat. Both on their own kills an auto, together are detrimental. The quicker and firmer the shifts, the longer an auto will last. The ONLY reason for a soft shift in an auto is for COMFORT and nothing else. Soft, lazy shifts is the equivalent of resting your foot on the clutch pedal 24/7

@r.weaver3769 3 жыл бұрын

Exactly. I learned this from my uncles transmission shop,

@jiffytoast 2 жыл бұрын

Yup I have a shift kit on my Silverado you get used to it.

@GrupaNation Жыл бұрын

Owned my jeep for over 4 years. I've learned so much from you. This is the "upgrade" I didnt know I needed

@SirArcticPB 3 жыл бұрын

I love that even tho you did it already once. You still took the time to show both ways and your Martin built way.!!!

@John-Dough_NineFoe 2 жыл бұрын

just did it, reall is worth the time, i was scared but took the leap, will be back for update later

@jamesdewer 2 жыл бұрын

Did this on the way to work this morning. Thanks to this video it took one hand to hold my coffee mug and the other a pair of wire cutters. Diagonal pliers. Thanks again, bow down to the king

@bot4lifezipsp 3 жыл бұрын

Been there done that for both of my jeeps, rolling like this for past 4 years. Thank you for making this video, more people need to know about this. Makes jeep lil faster!

@martinbuilt 3 жыл бұрын

Yes it does I like that firmer shift from 1 to 2

@SWAMPKINGDOG 3 жыл бұрын

Done it today! V-8 HO 4.7 ‘04 2wd...simple..”caught 2nd hard” as in squealed tires!! Kool...zero issues

@ProjectDanH 3 жыл бұрын

Awesome Martin! These WJs are way more advanced than the XJ.. I'm learning a ton from your channel. 💪

@martinbuilt 3 жыл бұрын

Thank you, Dan, I appreciate that. You and yours have a wonderful Christmas and a great New Year.

@Mr.J0lllllll0 2 жыл бұрын

Accidentally coming across this video is a game changer, I've been wanting to do this but never had time to research anything.

@martinbuilt 2 жыл бұрын

I'm glad you found it helpful.🙂👍

@user-nf3ys9vg3k 3 жыл бұрын

I’m going to delete torque management, tomorrow. I laughed so hard at the end, “I don’t know what it is.” It’s truly deleted. As always Martin great stuff! 🙌

@martinbuilt 3 жыл бұрын

Glad you enjoyed it! Yeah I had a brain fart there...😅

@user-nf3ys9vg3k 3 жыл бұрын

@@martinbuilt I thought it meant you where acting as if it didn’t exist.. as a joke. 😅

@justScrollin0627 3 жыл бұрын

4 Things..... 1) I wish you owned a Jeep Grand Cherokee 05-10 because mine is a 09. 2 )If I was one of your neighbors you would have to throw things at me to keep me away from you while you were working on your Jeep! 3) You are an extremely smart individual and really enjoy watching your videos! 4) Hope you and yours have a Merry Christmas!!🙏

@martinbuilt 3 жыл бұрын

Thank you, Gregory, I wouldn't throw nothing at you...Lol Hope you and yours have a wonderful Christmas!

@ChainsawFPV 3 жыл бұрын

2nd time I was brought to your channel for help. 1st was that ram air. Using existing air box for that was genius! I was going to 90 up to hood and leave it until seeing your video. Thank You!!

@martinbuilt 3 жыл бұрын

Thank you, glad to see you made it back to another one of my videos😀👍

@charliedee9276 2 жыл бұрын

I did this to mine 2 years ago, I swear it gives a chirp on the 1-2 now.

@UncleRoots413 3 жыл бұрын

Martin. I have a 04 Dakota but have learned much about it from you. This particular vid doesn’t apply to me but Im watching anyway cause I like the tech stuff too. Thank you for doing what you do.

@martinbuilt 3 жыл бұрын

Thanks for watching, I just recently picked myself up a 2001 Dakota 4x4 with a 4.7 regular cab.

@UncleRoots413 3 жыл бұрын

@@martinbuilt quad cab 5speed here. Most affordable non full size quad cab v8 i could find. Got the rundown on the HO cams and timing chain stuff from your other vid even though I have the Haynes near by. Cams and chains on today actually. You made it easy, almost like I did one of these before. Glad i found your channel, keep it up. Thank you much.

@ipfarms 3 жыл бұрын

I learn a lot from you Martin, good and very clear tutorial ! thanks a lot Martin,best regards from me, richard in Indosesia.

@martinbuilt 3 жыл бұрын

You are very welcome

@neoobi32 Жыл бұрын

I love this. I did it the other day after watching.

@martinbuilt Жыл бұрын

Hard to say no to better gas mileage. Especially with today's prices. I'm glad you liked it and found it helpful, thank you for watching.

@brynnond.6952 Жыл бұрын

Just finally did this today to my 02 wj, only shifts fast when I absolutely smash the pedal to the floor but wow it shifts good now, crazy how one wire can make a worn out 21 year old suv feel faster

@michealbaer4917 3 жыл бұрын

I have manual transmission, but I enjoy your work...I drive for a living and love the manual 😊 over slush-mattic what you have...!

@martinbuilt 3 жыл бұрын

Thanks for sharing!

@taurus5151 22 күн бұрын

Уважаемый Мартин! ты супер! спасибо за совет! мое уважение! из России с любовью...

@danhambrick6331 3 жыл бұрын

Thanks Martin, you're the Man.....

@martinbuilt 3 жыл бұрын

You are!

@Logan-de3xx 2 жыл бұрын

Thank you for this Martin!

@martinbuilt 2 жыл бұрын

You're very welcome. I'm glad you found it helpful.

@gregj.gotham4402 3 жыл бұрын

I’ve learned alot by your videos i thank you martinbuilt

@martinbuilt 3 жыл бұрын

Thank you, Greg, glad you like them and find them helpful.

@lionelanderson2368 7 ай бұрын

Its a bit different on RHD of course, but the same 8mm etc etc, so still easy. I pulled the wire from the connector and used insulation wire to wrap it, then put it all back together, so it looks like factory. I love the "free" ideas that make your car better.

@martinbuilt 7 ай бұрын

I'm glad you liked it and found it helpful. Thank you for watching.

@TheCjcoon 3 жыл бұрын

Just did this! So nice!

@martinbuilt 3 жыл бұрын

Wonderful! 👍

@terrystratford1235 2 жыл бұрын

Oh how I wish I lived near you! I think you would be working on my wj more than I drive it!!😅

@tonyduncil3115 3 жыл бұрын

You did the video lol great job man

@adrianbiegaa9773 2 жыл бұрын

I just love this mod :)

@martinbuilt 2 жыл бұрын

I'm glad you like it.

@Danielprokopij 3 жыл бұрын

Cool mod Martin! I have heard of it. Im going to use a combination of your tips and see about making a connection that can easily be plugged and unplugged similar to yours 👍

@martinbuilt 3 жыл бұрын

Sounds great! Thanks for watching

@haniajlouni6396 3 жыл бұрын

Hi and thanks from Jordan , you are the best ,,👍

@martinbuilt 3 жыл бұрын

Thank you I appreciate that!

@JL___ 3 жыл бұрын

LOL Loved the outtake

@jp9579 3 жыл бұрын

Nice video as always. Of course being in the northeast this would be a 2 day project just getting the connector apart only to discover green crusties in there! Haha

@martinbuilt 3 жыл бұрын

yeah working on on vehicle from the southwest is easy compared to the rust belt.

@ivanvujadinovic9905 3 жыл бұрын

Worth mentioning that if you installed the TrasGo shift kit, and used the resistor it comes with, you already override the torque management.

@martinbuilt 3 жыл бұрын

Thank you for the tip

@rigobertoroman2625 3 жыл бұрын

Thank you for the info

@martinbuilt 3 жыл бұрын

Any time!

@jeeploggernz2289 3 жыл бұрын

Oooohh i need to check this out under my hood, mines a 04 HO with 5speed trans, hopefully its a 3 plug or im screwed haha, cheers Marty great informative vid, I'd be silly not to sub 👍

@martinbuilt 3 жыл бұрын

Should be a 3 plug.

@brackoncorbridge1966 3 жыл бұрын

I would of never of thought of this. My jgc has great throttle response alrdy but sweet I'm gonna make it better woot.

@martinbuilt 3 жыл бұрын

Glad you liked it

@reptilian6413 3 жыл бұрын

The superchips flashpaq 3874 does this too, I have it.

@gabrielgarivay3277 10 ай бұрын

thanks Martin

@martinbuilt 10 ай бұрын

You're welcome i'm glad you like it and found it helpful.

@tylerlarsen3572 3 жыл бұрын

I've been a fan of yours for about 6 months now, I've learned so much from you and working on my 00' durango. I was wondering if there was any reason I wouldn't want to do this on my rig?

@martinbuilt 3 жыл бұрын

if you have 45RFE transmission I would recommend it.

@jdsrcs8061 3 жыл бұрын

I have been thinking about doing this for awhile now. So I'm assuming that passing is going to feel like rocket.

@brucewhite7069 3 жыл бұрын

Gonna try yellow with the green stripe number 10 lead

@kelvinstrickland7442 3 жыл бұрын

Great Video. Going To Do This To My 2002 Jeep Grand Cherokee Laredo 4×4 4.0 l6 engine. I like the quick hard shift and I've owned many old fast cars and trucks and I always put a shift kit in but this is Free Of Charge With The Same Results. Thank You.Now Can You Get Me More Gas Mileage lol. I put a 4 inch lift And 33 inch × 12.50 R17 and It's viscous on fuel but it costs money yo have the look and off road capabilities.

@mandrews1192 3 жыл бұрын

I'm pretty sure it's only available for the 4.7

@jonwilson84 Жыл бұрын

I’m not sure if you get these anymore but I have watched all of your videos and I did this to my 2004 keep 4.7 and when I cut the wire now it howls in like 2nd gear and I am not sure why I have looked everywhere any help or ideas?

@carlosantoniougaldebalderr7722 3 жыл бұрын

hi!!! I have a question. how can i reset the tcu or tcm?? just reset, thanks a lot

@TheEyesOffire 3 жыл бұрын

It will real havock on your transfer case if you have 4x4 if your miles are high. I learned this the hard way just a heads up! The hard shift will fling around that front propeller shaft.

@camdenlassiter2725 3 жыл бұрын

Just with 4x4 engaged? Or also in 2x4?

@codybertram6122 10 ай бұрын

Even In 2wd the transfercase chain still sees power.

@romeolopez-ix3ck Жыл бұрын

Hi..its work for jeep grand cherokee 3.1 td 2000, with 44re trans? Thank you

@canecorso9439 2 жыл бұрын

I just smoke a bowl after finishing up a product and started watching your video, but I thought I was tripping when you faded in lmao

@martinbuilt 2 жыл бұрын

I'm glad you liked it 👍

@canecorso9439 2 жыл бұрын

@@martinbuilt I'm not gonna lie, it scared me at first. But looking back I was just up to late lmao but still inspirational

@conan670431 Жыл бұрын

Is that mod for the 4.7 only or for the straight 6 as well ?

@pug306dturbo100 Жыл бұрын

Hi mate .I live in England and my Jeeps TCM is on the right hand side of engine bay will this be same passenger and are you. Sure this will do no harm

@HerbZilla 2 жыл бұрын

My 4.0 has an extremely hard shift when going up hills on the freeway. I am not sure how to fix it. It like skips gears and bypasses a gear or 2.

@brendandonovan9040 8 ай бұрын

Hey Martin will this work for a 1999 wj 4.7?

@alexchung5804 3 жыл бұрын

Great video as usual Martin, I literally did this last week to my WJ. I like it so far, thinking about running wires and putting in a toggle switch. Do you think 18 gauge wires would be suffice to complete the job and where would be a good place tackle when running those two wires through the firewall? Thanks @martinbuilt

@martinbuilt 3 жыл бұрын

There's a couple places one would be on the driver side where the harness comes through the firewall you'll find a couple small grommets near that harness that are easy to run the wires through and then there's another place behind the ECM or the harness goes through the firewall.

@petertarantelli 2 жыл бұрын

Another great video and easy to do mod. Question, in your experience, of all the WJ years, is there one you would recommend over another? I really like the WJ style and I’m thinking of towing (no more than 4,000 lbs).

@martinbuilt 2 жыл бұрын

Thank you, I am partial to the 02-04. I like how the EVAP got moved to the rear of the Jeep this made more room under the hood, grill and bumper changes, and HO engines. The only thing I didn't care for in the 01-04 with the 4.7 is the hydraulic cooling fan.

@petertarantelli 2 жыл бұрын

@@martinbuilt …thanks! I know how you feel about the hydraulic cooling fan, watched that video from start to end.

@brynnond.6952 2 жыл бұрын

I just got a 02 Wj with the 4.7 and I hate how soft it shifts. I wish it shifted like my old 2000 wj 4.0

@Den-tx1ml 3 жыл бұрын

Thanks for your videos. I assume you have 45RFE or 545RFE transmission, did you improved it with overhaul kits anyhow?

@martinbuilt 3 жыл бұрын

It has a 545RFE transmission, I haven't made any other mods to the trams as of yet.

@jayestevez8712 Жыл бұрын

Do a 2017 version do a 5.7 Jeep grand Cherokee summit

@brianhurst8862 3 жыл бұрын

Martin , I have a 2003. Great video by the way. Where is the tcu in mine? It's not where yours was in the video. I've looked but can't find it. I know where the pcu is. Is the tcu part of the pcu in my year model? Thanks in advance!

@martinbuilt 3 жыл бұрын

If you have a 4.0 engine, you have the 42RE trans and this mod won't work.

@chrisbeitzel4788 3 жыл бұрын

Hello Martin, I also have the Trasgo kit and the Sonnax line pressure booster kit. I'm having a code that's not letting the TCM talk with my ECM. Do you think disconnecting this will help? Many thanks to you and your time.

@martinbuilt 3 жыл бұрын

Hello Chris, I'm not too familiar with the Transgo kit I don't think disconnecting that wires going to make any difference but it wouldn't hurt to try.

@hellcatrider7077 3 жыл бұрын

Hello there I am trying to get more power out of my 05 Durango 4.7 currently I have a CAI a resonator delete and a dynomax race bullet muffler what are more ways to get more power out of my 4.7 I want to do a clutch fan delete and go with an electric fan but idk about doing it my self thanks.Love yours videos tho

@martinbuilt 3 жыл бұрын

Thank you, a good way would be to find yourself a set of HO camshafts or even a set of 08 camshafts

@francisbrackney2061 3 жыл бұрын

Hey Martin...is there any similar modifications like this one, that you know of for a OBD1,? we have a 1995 ZJ with the 42 RE, and the 4.0.

@martinbuilt 3 жыл бұрын

Not that I'm aware of.

@theoldstyle7453 3 жыл бұрын

Is this the same for the 4.0 WJ's too?

@martinbuilt 3 жыл бұрын

Unfortunately it will not work with the 4.0 equipped Jeeps they utilize the 42re transmission.

@feasiblepj 11 ай бұрын

02 4.7HO here. Had to do plugs, coils, MAF sensor, IAC sensor, TPS sensor. Ever since doing this I cleared all misfire codes but it throws P0700 and P0740. If I cut this wire will it make torque converter CEL codes go away, or will it throw more codes?? Any help greatly appreciated.

@feasiblepj 11 ай бұрын

Note once every 10-15 starts the thing runs like a dog spews smoke out the tailpipe and will stall at idle- will restart and it will run normally, but at stops RPM will bounce from a good 600 to 400. Letting off gas in higher gears trans will act up. Rough shifts here and there. Overall tranny shifts good. Its like the Jeep is haunted. Im thinking vacuum leaks.

@SirArcticPB 3 жыл бұрын

Hey Martin. Idk if you could help, But I just tried this and my check engine light came one, and sent code p0206. And says cylinder 6 is open so I rewired the yellow green strip wire and my check enginelight went off and wasn't rough idle. I also cut it from the second location, 8 spot. Any suggestions??

@martinbuilt 3 жыл бұрын

That is so weird because that wire should have nothing to do with any of the cylinders. Try using an ohm meter going from the wire that you cut back to the number 10 position at the TCM to verify that it is the correct wire.

@ctdope Жыл бұрын

Martin, can you make a video on how to change the ABS sensors front and rear? I have a Haynes manual but it doesn't give any info on it. It says have the dealer service it. I have 4 new ones to install, and have no idea where to find the connections without tearing up entire interior. Please help. Thanks.

@ctdope Жыл бұрын

Nevermind. I took out my back seats with all the brackets, lifted carpet, and found both connectors, on each side of tunnel. Tomorrow they get replaced.

@toddwhitehair3378 3 жыл бұрын

Can this mod be done to a 545RFE trans on my 06 grand as well? I did the line pressure boost With the special pigtail.........

@martinbuilt 3 жыл бұрын

no, this can only be done to JTEC ECM vehicles

@JF32304 2 жыл бұрын

Hey Martin, I recently changed plugs on my 04 4.7 HO and now I have a high idle (around 900 RPM). I didn't change anything else. It idled and about 600-700 before. The old plugs had a huge gap almost .125 the new ones obviously didn't have this. Could this be caused by the TPS? I've reset the computer and still a slightly high idle. At first start it hits 1500 then comes down. What would cause this. Appreciate any info.

@martinbuilt 2 жыл бұрын

I'm betting when you change the plugs you disconnected a vacuum line somewhere. you may have not even realized it and you have a vacuum leak and that's why you have a high idle

@mandrews1192 3 жыл бұрын

Do you still get the faster firmer shift if you shift it manually at the track instead of leaving it in drive?

@martinbuilt 3 жыл бұрын

yes it shifts firmer in both D and shifting manually, I would like if it shift quicker though.

@TOO_RAW 2 жыл бұрын

Hey Martin, long time fan and WJ enthusiast here, I did this to my 01 4.7 with noticeable results, I recently ended up with an 04 laredo 4.0 in killer shape and I was curious if it's the same process to ditch torque management for a 44re as it was with the 45rfe? It worked wonders on the black beast and was curious if it was more or less the same for the silver chariot with a 44re. Thanks in advance, -Alec

@martinbuilt 2 жыл бұрын

As far as I know, it is a 45RFE and 545RFE mod only... Take a look and see if there is a green with a yellow striped wire in the number 10 spot of the TCU. And then cut it… lol and see what happens. Thank you for supporting the channel and watching. I appreciate that.😉😎👍

@TOO_RAW 2 жыл бұрын

@@martinbuilt that's right, worst case scenario I have to reconnect it and reset the tcu and ecu lol.

@rodom303 3 жыл бұрын

Could you tell a big difference between shift times?

@martinbuilt 3 жыл бұрын

it is quicker, firmer and zero cost

@tylerdubois9020 3 жыл бұрын

Martin, Do you plan on doing a re-wire tuck and relocation for the computers? If so where do you plan on relocating them? I'm wondering because I am sure off-road WJs would like to have their computers hidden instead of getting splashed when going through streams or mud. Thanks, Tyler

@martinbuilt 3 жыл бұрын

I am planning on moving the TCM for sure unfortunately it's going in a place where an off-roader would not want it just behind the transfer case near the frame. The ECM is going to most likely stay where it's at I'm just going to make the wiring look way better. I had thought about moving the TCM into the glove box location and sacrificed the glove box.

@xc8487 3 жыл бұрын

The computers and wiring will be fine, they're designed to withstand water submersion. What's really important is your engine, trans, tcase, and axle vents or openings.

@tylerdubois9020 3 жыл бұрын

@@martinbuilt What is the advantage of moving it by the t-case? is this for asthetics for the clean and accessible engine-bay?

@edwardceijas3905 3 жыл бұрын

Is there a video on how to install an oil catch can on a Dodge Ram 4.7L 2003?

@martinbuilt 3 жыл бұрын

I need to do one.

@swolneck8615 2 жыл бұрын

I have a 99 grand cherokee 4.0 and I don't see a yellow with green stripe wire any suggestions?

@martinbuilt 2 жыл бұрын

The reason is you have a different transmission with the 4.0 I don't think you have a transmission control unit either do you?

@alexandersinclair5479 3 жыл бұрын

Just did this today and now i feel like its in limp mode and got a code p0700. Did exactly as described in the video, any thoughts as to why? 2000 4.7L

@martinbuilt 3 жыл бұрын

The only way I can explain that as it's got to be the wrong wire

@jcstevegigs 2 жыл бұрын

Did you solve this? One other guy said his #8 wire was pink

@roylyle4339 Жыл бұрын

TCM?TCU Automatic Transmission Control Module TCM TCU 56044573AA ? is it a 4o5 ?

@pottaz 3 жыл бұрын

Awesome video and content on your channel. Keep up the great work. Question from my side. I am having an issue where the engine will stall when shifting from N-D or N-R or P-R or P-D. Don't have any error codes related to gearbox. This also only happens when the vehicle is warmed up. 545rfe transmission. Sometime when idling in P or N the engine will stumble and drop rpm then recover again. Any pointers will be appreciated 😎

@martinbuilt 3 жыл бұрын

That definitely sounds like the idle air control valve either needs to be cleaned or replaced.

@chrismorton4533 3 жыл бұрын

This sounds a bit like a worn out torque converter. There is two parts the will slip on each other when you're at a stop to keep the engine running but when it wears out, it binds and causes the engine to stop when engaging in a drive gear. That's why when you go from P to N it will stumble but stay running. That'd because both P and N are neutral gears whereas drive engages your car to the ground. It's almost like leaving the clutch out in manual and stopping at a red light. Check your fluid level and condition, hope this helps. Great vids Martin!

@pottaz 3 жыл бұрын

@@chrismorton4533 thanks for the insight. I changed the IAC but still the same issue. Also think this is more gearbox related. What I have noticed is when I cruise on highway speed with my foot stable on throttle with a small incline, it's as if it is engaging and disengaging the lockup clutch. The rpm wil fluctuate and can feel it fluctuating. This happens repeatedly. Also when I sometimes engage D it will have a harsh kick where the car will jump forward. Does that diagnose it to the torque converter on it's way out?

@pottaz 3 жыл бұрын

@@chrismorton4533 I have alos read up on the Torque Limit Valve Spring and heard that they also fail. Could this also be the cause or will that cause different issues?

@jcstevegigs 2 жыл бұрын

@@pottaz did you solve this problem? I think I’m having a similar situation. Thanks

@mmmachines 3 жыл бұрын

Great video Martin! I have a 2000 Dakota 4.7 Magnum. Do you think it will work on this? Thanks

@martinbuilt 3 жыл бұрын

Yes it should, I just got a 2001 Dakota with a 4.7 and will be cutting the wire.

@mmmachines 3 жыл бұрын

@@martinbuilt I will definitely be looking for that yellow/green wire. That will be a nice little mod to add to my 70mmTB, dual short air intakes with heat shield below, fan clutch delete, magnaflow w/ dual exhausts, and twin hood scoops with one scoop with the customized old air box fitted tight against the hood cutout (like the one you did in a previous video). Hope to see some videos with your new '01 Dakota. There's a lot of us Dakota owners out here ;)

@ascendantrobin3230 3 жыл бұрын

@@mmmachines potent recipe

@flwfranco2821 3 жыл бұрын

I ended up wiring in a switch to change driving styles

@pottaz 3 жыл бұрын

Will it cause issues if you change while driving?

@flwfranco2821 3 жыл бұрын

@@pottaz No. all this is doing is triggering the Fuel cutoff at shift points at WOT

@tonyphillips4981 3 жыл бұрын

What about a 2000 Dodge Dakota that I seen you recently purchased can you do this too?

@martinbuilt 3 жыл бұрын

yes you sure can

@guyprimo6414 3 жыл бұрын

I have a 03 jeep grand Cherokee 4.0 ltr. 4or select track. are you talking about the computer? I also dont see that TCM on my jeep, could you let me know how to do the delete my my jeep

@martinbuilt 3 жыл бұрын

I should have specified this is for the 4.7 L that utilize the 45RFE the 4.0 uses a 42re transmission

@lilfella8955 Жыл бұрын

Will this hurt my 4.0 ? I’m not sure juss asking wouldn’t mind doing it

@martinbuilt Жыл бұрын

I'm sorry but this will not work on the 4.0 it uses a different transmission then the 4.7 Thank you for watching.

@arizonaguy7574 3 жыл бұрын

Either we have seen this video before or I can see into the future.... Martin? :P

@martinbuilt 3 жыл бұрын

Maybe you are thinking of the 45RFE to 545RFE conversion video

@arizonaguy7574 3 жыл бұрын

@@martinbuilt you are 110% correct... My bad :)

@r.deanmcknight136 3 жыл бұрын

Would that work for an 03 Dak with the 4.7 and 545rfe trans?

@martinbuilt 3 жыл бұрын

I believe the 03 Dakota has the NGC ECM and if so it won't work. You can identify the ECM if it has four plugs on it it's the NGC if it has three plugs it's a JTEC

@r.deanmcknight136 3 жыл бұрын

@@martinbuilt the 02 had that, mine has the 4 plug...all in one unit

@SmudgyContent 3 жыл бұрын

Dun suppose this would work same for dodge Dakota? Idk if they ran same wiring diagrams as jeep or not...

@martinbuilt 3 жыл бұрын

I would imagine they do I'll have to look into it I just recently purchased an '01 Dakota with a 4.7

@SmudgyContent 3 жыл бұрын

HELLz YES BUD!!!! Lolz you will be happy with it... well maybe if u swapped out for a 545rfe transmission.... or a 5speed lolz .... I loved the 01 4.7L 5speed sport I had.... before I had found out about ur channel I was running a Fastman Dan throttle body and 08 cams intake and adapter from fastman Dan. I tried many different types of ignition coils and I finally found Sultans Of Spark coils for my 07 Dakota. They’re actually cheaper than OEM and they have 8.4ohmz vs the stock 7.3ohmz so this means yah gap ur plugs to about .65 for better burn...

@overlandingearth8440 2 жыл бұрын

This video is a little old and sorry to comment so late but a just had a question, I did the torque management delete which gave me more power that I didn't know my 4.0 wj had the only problem is now my speedometer don't work anymore would there be a reason for that cause I deleted the right wire any answers would be great.

@martinbuilt 2 жыл бұрын

This mode was only meant to be used on the 45RFE and 545RFE transmission. I don't think it will work with the 42RE transmission like you have like you have in your vehicle.

@overlandingearth8440 2 жыл бұрын

@@martinbuilt yeah didn't think about that lol and thank you for letting me know.....

@overlandingearth8440 2 жыл бұрын

And thank you for bringing up the transmission cause I want to update and upgrade everything I can the wife and I got this at I believe a not to bad of a price have all the receipts carfax matches everything had transmission work done already but would still like to update anyone with any tips we appreciate thank you everyone...

@luckycharles5826 2 жыл бұрын

Hi Martin can I use 0w30 oil on my wj 4.7l

@martinbuilt 2 жыл бұрын

Well this is what Google has to say about it. 0W-30 is a special type of motor oil. It has a low viscosity and can be used in place of 5W-30 or 10W-30. The 0W-30 is a fully synthetic motor oil type that is capable of enhancing and improving fuel economy due to its lower friction properties. I may give that a try for the winter and then back to 5W30 for the summer.🤔

@rodom303 3 жыл бұрын

Can torque management be modified in a program like HP tuners to get more power out of shifts compared to disabling the system entirely? Not too familiar with how torque management works

@martinbuilt 3 жыл бұрын

yes, in a HP Tuner torque management can be modified.

@rodom303 3 жыл бұрын

@@martinbuilt can it be modified to increase power more or equal to a delete?

@DRIFTERz1973 3 жыл бұрын

Is this the same thing for the durango 01

@martinbuilt 3 жыл бұрын

Yes I'm pretty sure that it is, I just recently picked up and 01 Dakota so that would be something I'll be looking into.

@MarkAlves1982 2 жыл бұрын

Would depinning the wire be the same as cutting it?

@martinbuilt 2 жыл бұрын

Yes, that would be the same.👍

@ericrainey3893 Жыл бұрын

Can this be done to a 2007 grand Cherokee 4.7?

@martinbuilt Жыл бұрын

Maybe with some type of after market programmer.

@toddwhitehair3378 3 жыл бұрын

Hi Martin Have you done anything with the Hemis yet? I have an 06 grand Cherokee with 5.7 Hemi...........

@arizonaguy7574 3 жыл бұрын

*perk*

@martinbuilt 3 жыл бұрын

no have not got into the Hemi yet.

@nateloy8964 2 жыл бұрын

Can you do this to 01 WJ with a straight 6 4L?

@martinbuilt 2 жыл бұрын

No, this only works on the 45/545RFE transmission. Your Jeep has the 42RE trans. 😕

@mandrews1192 3 жыл бұрын

Do we need to disconnect the battery before doing this?

@martinbuilt 3 жыл бұрын

I wouldn't but, the service manual will tell you to disconnect the ground side.

@martinadams7949 2 жыл бұрын

can you do this on the 4 plug ECU?

@martinbuilt 2 жыл бұрын

Not that I know of. You would most likely need some type of performance programmer.

@400boys Жыл бұрын

Do you have rev limiter on your jeep ?

@martinbuilt Жыл бұрын

Yeah, I believe the factory setting is at 5800 I was able to turn it off and have turned 6300 RPM before.

@timedmonds554 3 жыл бұрын

Hi Martin I wondering if there is a way you can help me

@martinbuilt 3 жыл бұрын

Sure you can contact me through my Facebook link in the description

@GaragemV8Bramont 6 ай бұрын

How can I disable on 44RE 1997 Grand cherokee 318V8? Can I?

@martinbuilt 6 ай бұрын

Not that I know of.

@robgoffroad 3 жыл бұрын

I just attempted this on my 2002 Overland. I went out there, found the gray connector (the larger of the two) and cut the yellow/green wire. Then when I went for a drive, I found that I had no speed or odometer. And my check engine light came on (P0500 -- no speed sensor). So I came home and reconnected that wire with a butt connector. I cleared the code, went for another drive. The check engine light came back on (same code), though I have speed again. I keep clearing the code but it won't go away even after reconnecting that wire. I came back and re-watched this video. On my WJ, it's a pink wire with a green stripe that is in that #8 position. I hadn't paid attention to the actual wire position; I just focused on yellow/green. So it's worth nothing that the wire color may not be the same. But now I have a new problem to figure out with the CEL. Sigh. At this point I'm not cutting anymore wires.

@jcstevegigs 2 жыл бұрын

This is always my fear doing something like this...did you get it straightened out? So what you’re saying is it’s the #8 wire regardless of the color? I have an ‘02 4.7

@robgoffroad 2 жыл бұрын

@@jcstevegigs No. I just reconnected the wire and said to hell with it.

@tonyphillips4981 3 жыл бұрын

This only for the Jeeps 4.7s? What about the Dodge 4.7?

@martinbuilt 3 жыл бұрын

It will work for them too with the JTEC ECM

@karimqamberi931 Жыл бұрын

Can u just cut the wire? N cover them after?

@martinbuilt Жыл бұрын

Yes that will work. Thank you for watching.

@xrpinvested970 3 жыл бұрын

Hello sir, just came across this video. Subscribing now. I have a 2004 Overland with 6.5” lift and I pull my boat which ways with the trailer 4200lbs. Just a 10 min backroad ride to the lake. Going to try this but I was wondering if anyone makes a chip for the HO motors? Called Superchips and was told they only make one for the non HO motors. Thanks!

@xrpinvested970 3 жыл бұрын

Or a tuner?

@martinbuilt 3 жыл бұрын

It can be done with HPtuner but that would cost you $500

@xrpinvested970 3 жыл бұрын

@@martinbuilt would you say it’s worth the money? Or would going from 3.73 gear to 4.56 be more beneficial? Thanks again.

@nate4036 3 жыл бұрын

@@xrpinvested970 anytime you start adding weight to the equation, 9 out of 10 times, gears are best choice. Even take full size trucks.... same drivetrain but weight ratings increase with gearing. It simply makes life easier for your powertrain