How to disassemble and find problem in Milwaukee M18 cordless drill faulty gear assy

Рет қаралды 118,904

7 жыл бұрын

In this video you will see how to disassemble and find problem for Milwaukee M18 cordless drill, This one has a faulty gear in gear assembly, and it needs a whole new gear assembly.
Be sure to like this video and subscribe for more fresh updates! We try to put out the best content for power tool repair, helping you keep your kit in working order!
~-~~-~~~-~~-~
Check out the below links where you can find new versions of some of these quality brands. That is, of course, if your repairs don't work! As an Amazon Associate I earn from qualifying purchases.
Makita: amzn.to/2IBBDso
Bosch: amzn.to/3o4DmH2
Milwaukee: amzn.to/37iilCI
Dewalt: amzn.to/3nZVaDj
Metabo: amzn.to/31BeEEL
Thanks for visiting! #Handyman

Пікірлер: 40

@BenjaminKerr-yj4gs Ай бұрын

I wish these drills were still available to buy

@fredkrouwel8537 Жыл бұрын

Making it up as he goes along

@rcampbell1981 3 жыл бұрын

Thanks champ, much help!

@wowme110 5 жыл бұрын

I'm having trouble with screw that loosened to adjust for various bits. It wont go down to small and clamp the bit. You usually just have to retighten screw. But I cant seem to get it to tighten again. Open all the way or to where its stuck. Any ideas?

@nicholaschriss1706 6 жыл бұрын

Do you know how to repair a stuck speed selector on a M18 BPD?

@davidreynolds4684 Жыл бұрын

Im curious if hes going to install a new gear box or just the nylon . if it was mine from what i can see and from the countless tools ive rebuilt id go with the new nylon. The metal parts rarely fail. When they do its usually a break not worn. And a suggestion to anyone that has not done much of this work use a screwdriver or low speed setting if using a drill to remove case screws. The plastic strips out relatively easily when removing the screws on high speed. Does the same installing them.

@GuardianAngle93 2 жыл бұрын

Rear bearing on my M18 hammer drill blew up. Milwaukee refused to repair it because I had pulled it apart, bagged everything separate, and had the broken inner and outer magnet in a sack for replacement. Almost like they forgot I have a right to repair.

@zbornaja33 Жыл бұрын

I dissasembled my M18 CPD and found out gears are "eaten" in gearbox. It had a lot of years so that was no suprise. First maybe negative suprise was that i need to buy whole gearbox and it is impossible to buy just spur gears (nice work milwaukee, see what you did here...)...Ok i ordered gearbox and replaced it but i overlooked that motor assembly has also faulty, eaten gear. So i ordered this piece also. But when i assembled it together the sound i got was not ok, gears were not running ok. I opened it again and i saw that my new motor assembly gear got quite a wear from 5 min "work"...I put extra grease and all and assembled the machine again but it did not help, again i got sound that i did not like, gears being noisy and like there is friction...Now i dont know what to do and where is a problem. Anyone have any idea?

@suzesiviter6083 2 жыл бұрын

Anyone know about the pin outs on the m18 battery? you get a voltage between the two inner pins of 3.2v, however my impact sometimes stops working and then I check the inner pins and they are at 0v, i can reset the battery by plugging it into my drill to bring them back up to 3.2v then it works again, so the impact must detect a fault and tell the battery to disconnect the pins?

@porkgoog5383 7 жыл бұрын

Legend bro thank you so much! Wish you were local to me so you could service my tools :(

@Diverstj70 Жыл бұрын

What size torx bit are you using?

@freethinker5225 2 жыл бұрын

Do you know if newer tools have plastic gears...specifically from box stores such as home depot, lowes, and other hardware stores...my friend is telling me distributors have better gears that last longer

@sr8shoota 6 жыл бұрын

my armature seems to be wobbly in the magnet, took it out and the ware is different on stack laminations, the mtor doe not spin and it seems to be stuck.

@Sasha4966 6 жыл бұрын

Power tools fix . I have the same problem. Is it possible send to u . And how much it cost to fix? Or maybe u have video about ball bearing? Thanks

@MrSuperheterodyne 5 жыл бұрын

Would you say that Milwaukee make good tools? Wanted the opinion of a repair man who sees inside many different brands. Which tool make would you buy?

@jrowe9301 4 ай бұрын

I heard somewhere that an antenna or Wi-Fi allows your drill from Milwaukee, (at least the half inch impact driver), to be tracked anywhere in the world if you register it online. What if we wanted to remove that antenna or Wi-Fi so we had a more private tool?

@hayleykilvert20 5 жыл бұрын

hi mate just wondering do you know if you can swap that plastic gear for a metal one

@handyman7282 5 жыл бұрын

Hello, if you have same gear, but its made from metal then it will work. But in some cases plastic gears is made to be broken on overloads and if you put metal gear then you will have overload to next parts

@martyketner4090 2 жыл бұрын

5370 Milwaukee magnum hammer drill assembly

@agoboo 6 жыл бұрын

Man. Thank you. Can I ask you. When do you buy spares?

@calvinkline2846 4 жыл бұрын

good video! maybe next time clean it before reassembly that way it will last longer?

@handyman7282 4 жыл бұрын

Thank you, maybe you are right about cleaning

@calvinkline2846 4 жыл бұрын

@@handyman7282 its just something I have delt with in the past it tends to make it hold the heat in longer

@viettran-hp6pu 6 жыл бұрын

Hi sir I live in VN i have 1 hammer drill MIlwaukee M18 2702 after 2 weeks to work it is smoke and death, but body light on good i was check soldered it is good, please hepl me, because it is expensive . I buy on ebay, i cant go to usa take it back under warrenty

@bmanmitch2005 4 жыл бұрын

What size torx bit driver fits the screws?

@handyman7282 4 жыл бұрын

Hello, if I remember good it was TX6

@handyman7282 4 жыл бұрын

but you need TPX6 with hole on bit center

@bmanmitch2005 4 жыл бұрын

Thanks

@timbrubeck4212 4 жыл бұрын

mine did the same to my damn gloves....i was like wtf....does this go for the brushless drill also?

@stevenc8140 5 жыл бұрын

Comrade? You have done this (AT LEAST!) one time before....How does a $599.00 Highly Rated cordless Drill...Become a total piece of CRAP! With a slipping clutch mechanism? With in ONE YEAR?

@-fazik-3713 4 жыл бұрын

The tools are build to fail now. If someone uses them more than average they fail before the warranty runs out.

@groupb5420 2 жыл бұрын

I’ve had Milwaukee tools for ten years The drill is still working The impact driver is still working The cold cutter ( for cutting unistrut and stud ) broke two years ago , i dissembled it and found the rotor on the armature had snapped ( I was cutting cable tray at the time) ordered a new armature motor £38 and still working. These tools are used and abused every day , sometimes dropped from height, used as hammers and yet they still work with the same batteries 18 volt 4 amp …. fantastic tools wouldn’t buy anything else highly recommend.sparky U.K. 🇬🇧👍