I have 03 beetle 2.0 and it stopped pulling so I checked the trasmission fluid.started it up it smoked really bad.its never done that,ran for 10 minutes and stopped.its got a loud tap so do you know if it's a valve, timing,or the engine just shot.if you could reply I would appreciate it bro
@leanncole15954 жыл бұрын
How do you get to the part 2 reinstallment of timing belt and water pump for 2.0 vw beetle Jetta avg
@MrMoosetang13 жыл бұрын
Part 2 is just wishful thinking? Lol
@CodytheCarGuy9 жыл бұрын
ok i shot the part two but it seems to have gone missing so part two will be back up later this week sorry bout that everyone i dont know how that happened. Thanks for watching !
@kelbel8449 жыл бұрын
please hurry i cant figure the tensioner out
@CodytheCarGuy9 жыл бұрын
whats your email ill tell you how its easy
@CodytheCarGuy9 жыл бұрын
Kelli Brklacich whats your email ill walk you right thru it
@flenny9 жыл бұрын
Da Car Did you have the head resurfaced before reinstalling? Could be a warped head not sealing properly
@diego66979 жыл бұрын
I NEED PART 2 PLEASE!!
@albs195710 жыл бұрын
I just replaced my timing belt, tensioner & water pump after watching this video. Thank you for the "junkyard version". It really helped to have a clear view of the work prior to doing it.
@NicholasMaietta4 жыл бұрын
Thank you for this video. I'm 5 miles from a fire and desperately trying to save my VW from the fire. Had it all torn about and this morning working on getting timing done so I can get everything put back together and drive it off.
@phx2ewr9 жыл бұрын
Great part 1. Please post part 2!
@6769707211 жыл бұрын
Well done,I like the fact that you don't hammer everything off with an impact gun and air ratchet! Looking forward to part 2.
@Ben-jq5oo4 жыл бұрын
Very good demo, thanks. Having the engine out was a big help for me. I just learned that the water pump is driven off the timing belt as compared to chain cam engines where it has to be driven off the serpentine belt. Thanks again!
@callmekollect9 жыл бұрын
hey cody.i just got the entire kit and about to atemp this job tomorrow. part 2 would be greatttt.plz! this is the best looking video that i can use to get it done accurately.and the water pump and replacement of the timing belt is what i need.
@maceymacintyre8542 жыл бұрын
I really need part 2 please!!
@mor9h3us11 жыл бұрын
Fantastic start got us all interested BUT where's part TWO !!!
@samanthaviguerias71134 жыл бұрын
Morpheus Moss I need part 2!!!
@frankhoward76455 ай бұрын
3:10. Before you remove the serpentine pulley, you should note that there is a timing mark on the edge of this pulley that lines up with a slight depression on the metal timing cover. I painted these white.
@scooter81875 жыл бұрын
This guy makes good videos but this is the second one I watched (for Jetta 2.0) that didn't have a Part 2 as promised.
@NajmanAlpha5 жыл бұрын
Agreed...I need to replace the camshaft/lifters in mine and this is part of that job...both video part 2's would have been very useful...
@lourensdejongh37989 жыл бұрын
Would appreciate part 2 of this, thank you!
@lebaroncars10 жыл бұрын
great video thank you so much , took ours apart but was confused how the tensioner went on and you showed me
@travis91908 жыл бұрын
part two was great
@MrMoosetang13 жыл бұрын
Haha lol
@mojojo12111 жыл бұрын
we are still waiting for part 2 sir
@ElizabethNortje-nn3hd Жыл бұрын
Vwjeta 3
@MikeR-dc8bi4 жыл бұрын
Part 2 was super helpful thanks for the video!
@Audi598 жыл бұрын
cannot find your part 2 for this " how to do a timing becton your 98-05 jetta. 2.0 " can you send link...
@tsstn6 жыл бұрын
Cody, please either post the link to part 2, or link someones good video that covers what you lost, or just pull this down. Its really great to see this job without the car in the way so thanks for that but you rea)y should put the rest back up.
@CodytheCarGuy11 жыл бұрын
Yeah i have nice impacts but always find myself wrenching i feel like its better that way. Part two was going to be tonight but i got side tracked shooting my mini web series called scrappers , so ill finish the timing video tomorrow soon ill be shooting multi-cams too just waiting on my new computer to be finished being built to keep up with editing multi
@dlowcashemout31837 жыл бұрын
Hey nice video I was wondering if you had part 2 up. i looked I might've over looked it...
@eddyster565 жыл бұрын
You should make a vw playlist that I can share on the VW vortex as well as my local VW page!!! Thank you for this vid.
@sherrypeterson20318 жыл бұрын
Thanks for doing this video! Excellent tutorial, I am glad it's outta the car made it to easy to grasp! Do you have a video of this engine being put in the car?
@justywillnot36562 жыл бұрын
Where is part 2? I searched all over your channel. Wish it was available..
@RIVERLOPEZ7 жыл бұрын
Cody die in the attempt of shooting part 2. So part 2 will be done once a Cody's double is found! Be patient as it might take a while.
@x-man47027 жыл бұрын
Are you serious?
@wausauwausau10 жыл бұрын
I never heard of a 3/16 mm bolt until today
@Copewinter10 жыл бұрын
Quantity 3, 16mm bolts. There are 3 of them not 3/16
@obejopr11 жыл бұрын
part 2 ??
@angeltapia6826 жыл бұрын
Awesome mechanic! but I can't find part #2....
@moc15868 жыл бұрын
Excellent definition
@MELL0949410 жыл бұрын
Part 2 please
@Lwish711 жыл бұрын
any word on part 2 in the middle of replacing timing belt... having trouble setting timing belt
@anselmosoto2139 жыл бұрын
donde veo la segunda parte saludos desde mexico city
@TheSoloman2710 жыл бұрын
this is for the mk4
@johannesmahlangu28914 жыл бұрын
Thanks for a vw jetta 4 timing belt settings
@powderskihound8 жыл бұрын
I don't know what ever happened to part 2 but I don't see it here and shouldn't the video automatically load right into part 2? Do you have a link you can post that takes us right to part 2?
@ollydbg96532 жыл бұрын
awesome video, where's the crankshaft mark? thank you
@BisonThe4 жыл бұрын
My engine is disassembled and parts are spread everywhere in my garage since 2013. I've been waiting for almost 7 years for freaking part 2 and it doesn't look like it's coming out anytime soon. Well, guess I'll throw my car away or take it to the dealership :(
@Super1228913 жыл бұрын
So make sure the 1 spark plug is cylinders is at the top then put the line on pulley up top?
@mrcokez110 жыл бұрын
@Skyler no, you dont. but you have to remove upper and lower splashshields
@kennethmoll78933 жыл бұрын
Hey Cody. It is really a good video but I can’t find part 2. Can you help me?
@Mensch7712347 жыл бұрын
Thank you , you help me alot
@johnjrambo44108 жыл бұрын
can't seem to find pt2 vw jetta 2003 timing belt replacement. was you ever able to upload after it went missing? I like the video it has really helped big time.
@hectorvaldezhectorvaldez95279 жыл бұрын
Tank you for tips
@user-bz1fo2bm4m9 жыл бұрын
плохо что не показали крупным планом метки положения коленвала и распредвала.
@peterdatechmen55065 жыл бұрын
10k people worldwide with belt removed waiting for part 2. ..... ..... ......
@DR-um2bv5 жыл бұрын
Yeah I know right
@Yak54Fan9 жыл бұрын
Awesome, helpful video!! I am in desperate need of Part 2. What are the chances?
@mronemanband19 жыл бұрын
see my comment
@carlosaircraftmechxnic28196 жыл бұрын
Did you ever load part 2?
@clovely5139 жыл бұрын
Any luck with part 2? Really I'm just looking for a picture of the engine with the water pump removed so i can see if anything is missing from behind it.
@CodytheCarGuy9 жыл бұрын
whats your email ill send you a pic or better yet get me a pic ill know as soon as i see yours
@clovely5139 жыл бұрын
clovely513@gmail.com I'll get a picture soon thanks
@AUTOREPAIRGUIDE8 жыл бұрын
i found part 2 to be very helpful. thank you!
@sanderwalberg90267 жыл бұрын
Hi there, did you realy found part 2 ? if yes would you please put the link to it
@rodrigomunoz64244 жыл бұрын
Shit I'm still waiting for part 2 lol
@DR-um2bv5 жыл бұрын
Great video helped me out alot with my 1st vw timing belt, but my camshaft position sensor has thrown a code. So is that normally off 1 tooth, or do these sensors go bad if removed, I had to replace camshaft gear too
@pedrochip6 жыл бұрын
wheres part 2????
@smoothoperator16634 жыл бұрын
i had 2 throw the car away ,i can not find part 2 any where!
@brianparker35329 жыл бұрын
dude, did you every find part 2?
@angeltapia6826 жыл бұрын
Thank you!!!!!! I fixed it
@oscarromero73393 жыл бұрын
What socket do I use to take off the harmonic balancer
@MB-eo3mn Жыл бұрын
Why would you keep all the ratcheting but take out the actual timing part?
@joew72747 жыл бұрын
weres part 2
@carlosaircraftmechxnic28196 жыл бұрын
Thanks man!
@puppygadget31892 жыл бұрын
I'm looking at a 98 Jetta 2.0 to buy and was wondering if it's fairly easy to get to the timing belt to change it and the water pump while the motor is in the car? How many miles are one of these motors good for?
@mikenavarro31149 жыл бұрын
Can anyone help me I removed timing belt to replace the water pump but seems like I didn't set timing right and my car won't start now what shall I do?? Any suggestions . Please
@Mk4twoG Жыл бұрын
389k people are gonna need new motors now lmao
@jennayyguillen23994 жыл бұрын
I recently got on 03 Jetta (with a 2.0) as a project car, but I seem to be missing the lower timing cover bolts, I know you said they were a 10mm head size, is there any chance you know the thread size too? I want to go pick some up.
@emrogjata63782 жыл бұрын
how to watch part 2 please?
@buckshotgeorge72012 жыл бұрын
So where is part 2???
@Markdiego148 жыл бұрын
hi, were you able to put the part2 video up?
@AdvanceOne249 жыл бұрын
Really appreciate this video .... really helps! I hope you might be able to show a little more close-up detail on how absolutely, positively set the timing marks? I bet a bunch of us would be willing to chip-in and buy you a very large pizza for this :) !! Thanks again .... great video --
@gtk38498 жыл бұрын
Hey, I messed up the cam sprocket timing. how can I tell if its timed with no markings? I keep checking the bell housing and I cant see any indication what so ever. this is so frustrating. please help :)
@user-bz1fo2bm4m9 жыл бұрын
how do you know camshaft and crankshaft. where pointers. Video is not visible. and in English do not understand
@alvaro933643 жыл бұрын
where is part 2?
@arturoaguilar33647 жыл бұрын
Hello, i have to change my cam position sensor. Any idea how to remove my cam gear with out damaging it.... went to the junk yard and totally destroyed them. Pls help :(
@ohboydaceo2157 жыл бұрын
I was told the transmission code would be located in the trunk under the spare tire but no luck, anyone can help with this please. (99 jetta 2.0L stick shift) thanks in advance
@mariamyousafi81110 жыл бұрын
link to part 2 ?????
@ilib18497 жыл бұрын
is this also the same for the 1.6 100 horse golf mk3?
@panchovillaxx79 жыл бұрын
So the transmission needs to come out together? Did you remove the front?
@CodytheCarGuy9 жыл бұрын
No i was removing the engine anyways i just shot it like that for a better view , on these motors you don't remove the front clip of the car
@jisla210 жыл бұрын
where is part 2?
@delkyre19 жыл бұрын
need Some help, changed the water pump on my 2004 Jetta, Not easy at all. Got it back together and it starts but is out of timing, it runs. Any suggestions?
@CodytheCarGuy9 жыл бұрын
pretty much have to go back and redo the timing that car is a Interference engine so you can bend valves easily if your off on timing belt
@nfocus82469 жыл бұрын
I can't get my timing belt back on without a lot of force. Do you have any tips or tricks on how to get it back on? Its on the water pump and crank sprocket but just cant seem to get it on even with tensioner very loose. Also, I don't have a tool for the tensioner. Any idea on how to do final adjustment? My engine is in the car btw. thanks!
@CodytheCarGuy9 жыл бұрын
Yes it takes a lot to get it on then after you slide it over the pulleys' water pump, crank and cam it will loosen up some. I actually use a flat piece of metal to help slide it on.You dont need a special tool for the tensioner , anything like a small allen to hold it back will work then just simply line up the arrow to the v , tighten it and your done.
@nfocus82469 жыл бұрын
This thing KICK MY @$$!!! Everytime I thought I had it, the crank would turn a few teeth backwards. I finally got it to work by a) turning the crank a few teeth forward to account for it turning back and then b) sliding the tensioner halfway off the bolt it sits on. Had to get a lil mirror to line the the "V" and tha arrow and guessed my @$$ off as to what 15 ft/lbs feels like with a wrench. LOL.. The sad thing is. I saw a youtube video where a guy slipped his belt back on with tons of room to spare. That made me really think I was doing something wrong. you really ought to post part 2. People would probably vote for you if you ran for office. :) Thanks for responding.
@CodytheCarGuy9 жыл бұрын
Nfocus Onu yeah ive seen a few that people seem to have plenty of slack with the belt but i always seem to get the ones that are tuff to get on myself but i rather it be tight than too loose. As long as you got it in the middle of the v and tightened it then you are good. I always rotate the motor by hand a few times to make sure nothing hits and if nothing makes contact then your good. Yeah ill have part two up for the second time here soon. Ill have more jetta videos going up as well
@MAGWolf9 жыл бұрын
And what do you do when some moron prior to you owning it has stripped the 6mm hex bolts that hold the bottom pulley on? I am tempted on seeing if a mechanics will pull them off and replace them.
@CodytheCarGuy9 жыл бұрын
they are all sorts of fun to remove and yes if its in any kind of way messed up i always replace them!
@MAGWolf9 жыл бұрын
I pounded a 12mm Socket onto each one and they finally came out. Thankfully didn't have to drill them. Went to hardware store and got some new ones that are much nicer grade 10. Was not a fun job very little clearance on the Golf to do it. Now to replace my Inner Tie Rods and ends.
@AceHart91 Жыл бұрын
No part 2 and never showed how u set time for belt removal
@BruceLyeg5 ай бұрын
Hi Kitty
@lvtraviesa19 жыл бұрын
Ok I just changed my water pump everything on and now car won't start any suggestions
@CodytheCarGuy9 жыл бұрын
Hmmm hopefully you didnt get the timing off or mess up a sensor , id double check the timing
@alejandromoreno901010 жыл бұрын
Does any 2.0 engine fits on a 2005jetta 2.0? Or is it different
@CodytheCarGuy9 жыл бұрын
depends cuz a cabrio is a way diff 2.0 for those years and a 2.0 pre 99 is also different and some have fly by wire throttle bodies and some are cable you just have to look also some older are distributor and then they go to a whole diff system after 98
@brianf104910 жыл бұрын
We don't need the junkyard version.
@peteJoseph-x3h3 ай бұрын
5/8” ?…….16mm, you’re welcome.
@jaredtraver223210 жыл бұрын
Thanks, now i know with this engine in the car its not worth my time, SELLING CAR
@garethrees1007 жыл бұрын
Where the f uck is part two ????
@chipallen72997 жыл бұрын
garethrees100 i
@bahrimuhit68947 жыл бұрын
teach me
@onecoolwhitecatmotorsalesl8875 жыл бұрын
Come on
@ezra87616 жыл бұрын
Get a electric tool .. take less wrist stress
@johnnyfigueroa46906 жыл бұрын
Come on.. really. Codythecarguy.... 1159 video... "wooder pump"... 13/16mm bolt... This is a joke or you being serious? Be original.
@robertrukidding30559 жыл бұрын
Dude....WTF! You make no reference to the crank pulley mark and the pulley clearly moves when you pull the belt off. Wow!! Hope you're bonded :-) Luckily you have no liability for ignorant KZfaqrs fucking their engines based on your video.