How to Dot & Dab Insulated Plasterboard

How to Dot & Dab Insulated Plasterboard - a DIY Guide

Рет қаралды 884,402

Күн бұрын

In today's video I will be showing you how by installing insulated plasterboard, you can transform the warmth of your house!
You can buy me a coffee here www.buymeacoffee.com/charlied... or become a monthly member to unlock Discord forum membership, exclusive content and automatic entry into my FREE Monthly Giveaway. Thank you SO SO much!!
You can now access my 🛠Charlie DIYte Amazon Tool Store here www.amazon.co.uk/shop/charlie... - where you'll find all my tried, tested and much loved DIY tools arranged into handy categories.
Today's Toolkit:
- Kingspan Kooltherm K118 thermally insulated plasterboard goo.gl/zCPCq1 bought from SIG bit.ly/2BDCy5u
- Ox 5 gallon, 25 litre plastering bucket geni.us/t8BYFBI (Amazon)
- Gyproc Driwall Adhesive bit.ly/2S9hyJ7 £8.95; or
- Knauf Plasterboard Adhesive bit.ly/2N9CcYC £10.46
- Plastering trowel bit.ly/2S6g6qN £7.99
- Ragni bucket trowel bit.ly/2GuYun8 £6.29
- Plastering hawk bit.ly/2EdYyFN £24.98
- Unibond Super PVAC bit.ly/2BEiUpZ £20.62 or
- Thistle Bond-It bit.ly/2EeQeFw £71
- Stanley Rasp Planer bit.ly/2Ef0mhE £10.29
- Universal saw bit.ly/2X85UC8 £8.49
- Vitrex Power Mixer 1400 watt 230v www.vitrex.co.uk/products/140...
- or Plaster mixing paddle bit.ly/2SJs7Ys £8.76 for your
mains powered drill
- Dust mask bit.ly/2Gw7AAg £12.99
- Safety specs bit.ly/2X4VL9j £2.99
- Titan SDS drill bit.ly/2X85Kuw £59.99
As an Amazon Associate I earn from qualifying purchases.
I've now insulated 4 rooms in my house - 3 using this method of fixing insulated plasterboard with adhesive bonding, and our bathroom where I mechanically fixed the plasterboard to battens. I find adhesive bonding a much easier method as with battens you need to pack out each batten to get it plumb and to line up, whereas with adhesive bonding, you can use the thickness of the dabs to adjust the finished position of the plasterboard.
The ceiling in the spare room featured in today's video is lath and plaster - originally covered in wood chip wallpaper but recently stripped by us. The ceiling is well insulated in the loft space. The walls however are two course victorian brick with no cavities or insulation - in other words an open fridge in the winter. I'm gradually replacing the old windows with double glazing, but there's no point when the walls are so cold to the touch, so I stripped off the old plaster and render, and dot and dabbed them myself with Kingspan Kooltherm K118 thermally insulated plasterboard goo.gl/zCPCq1.
Building Regulations
- www.gov.uk/building-regulatio...
Kingspan Resources
- Kingspan Information Hub bit.ly/2V3WhCt
- Kingspan K118 Product Brochure bit.ly/2GQeAHp
- General advice Insulation Technical Service Department UK - Tel: +44 (0) 1544 388 601
- How to Guides and FAQs bit.ly/2trrjbB
- DIY Doctor bit.ly/2GrAnpq
SUBSCRIBE - you can subscribe to my Channel here:
/ charliediyte
LET'S CONNECT!
Charlie DIYte
-- / charliediyte
-- charliediyte.co.uk/
-- / charliediyte
-- / charliediyte

Пікірлер: 940

@graememaguire692 4 жыл бұрын

Charlie, tidy quality job. I've been plastering 40 years and I'd score you 9/10. Just a few comments, too much adhesive. Dabs only need to be 600 centres edge and middle of the board, dabs were too flat and should pretrude from wall 75-100 mm and board from window reveal out toward corner of the room All these tips will use less materials but all in all you have done a great job 👍

@handle1196 2 жыл бұрын

Does this mean start at each window reveal on the face wall not the actual into the window reveal? So board from edge of window towards the corners then fill in the gaps between the board under and above the window?

@stringerbell4711 5 жыл бұрын

Nice job Charl, I would never have known job like this had so many pitfalls for a nightmare outcome. Nicely explained, great that you listed all tools necessary. Really impressive, really interesting. Well done!

@profecarrillo6479 Жыл бұрын

those things are a fire hazard. use Hebel Masonry Autoclaved Aerated Concrete

@deanbond3204 3 жыл бұрын

Nice video, well explained and set out. Anything is possible with research, the right tools , and time. I feel D.I.Y gets better with trial and error, practice brings confidence to every job after the very first. What ever that might be. Thanks to guys like you , people can see its possible to have a go. Cheers 👍🏽

@reginap3472 2 жыл бұрын

Another brilliant video, thanks Charlie. The way you installed your insulation was so much more thorough than our builders! Re solid walls and dot & dab v mechanical fixing: On an early Victorian 4 storey terraced house, we were advised by Kingspan to mechanically fix on the 2nd floor where the walls are thinner and there was a risk of water penetration but I wanted to let others know that we got away with dot and dab on the 1st, ground and basement. The basement has no soil against it and the walls and floor were damp proofed with a Newton membrane. In addition, the walls get thicker as you go down the house so Kingspan calculated from our dims that they would not suffer from water ingress. We also observed the walls over a couple of years and knew that there was no damp issue. So it is always worth checking with the very helpful technical team at Kingspan.

@CharlieDIYte 5 жыл бұрын

For anyone thinking "didn't he post this a few days ago", you're absolutely right! I took it down to add a few important details!

@stephenoconnor1459 5 жыл бұрын

Are you going to plaster that yourself now or get a plasterer in to do it?

@CharlieDIYte 5 жыл бұрын

@@stephenoconnor1459 Check out the video linked in the closing screen. I got Gerrard a pro plasterer in kzfaq.info/get/bejne/gdmTZdCYzamRZJc.html

@mel7077 Жыл бұрын

I've learned so much from this. Was nearly about to have insulated plasterboard put up on all four walls without being aware of building regulations. Life saver, thank you!

@CharlieDIYte Жыл бұрын

You're welcome. With insulating internally like this, you need to pay close attention to cold bridging points (breaks in the insulation). Cutting through the board for plug sockets, where each sheet butts up to the next and around windows are the big culprits. Expanding foam adhesive is one answer rather than dot and dab adhesive but you have to choose an expanding foam that's compatible with the Plasterboard. It's well worth doing this but you have to get it right to prevent moisture from the house getting between the boards. 👍

@mel7077 Жыл бұрын

@@CharlieDIYte Thank you. Any recommendations on good expanding foam adhesive? I'll be using the Knauf Thermal Laminate and the Knauf Soundshield plus plasterboards.

@geowgeow Жыл бұрын

Instastik is a good one. Very easy to apply and is made specifically for this job.

@TheDoosh79 7 ай бұрын

@@CharlieDIYte Have you seen the gyproc insulated plasterboard? They do their own sealant for a mastic gun the same as your dot and dab approach, goes straight onto existing wall. Wondered about doing the two walls either side of the chimney breast as they're external and get really cold.

@gl5934 5 ай бұрын

I also thought I’d need to do this! Does the video relate to the building regs of today? Thanks!

@000gjb 5 жыл бұрын

Great video. A lot of useful basic information to tailor the insolation solution and cut down product research. Well made.

@ThePhilandPam 5 жыл бұрын

That’s a great job and have to say I really enjoy a longer video like this....settles down with a cup of tea 😊👍

@CharlieDIYte 5 жыл бұрын

Thanks mate! A lot of people split them up into a series but I think where possible it's best to keep it as one. That way you're not jumping around trying to find the next video!

@Jackzuk 5 жыл бұрын

Great video Charlie, it is something I really want to do and something I have researched a ton about, reading all the technical data etc but still feel there is not enough info out there. However this is by far the best video i have seen. I would love to pick your brain as you too appear to have done a ton of research. The main areas I have concerns with is the vapour barrier and access for wires without cutting or making holes in the insulation. So my thinking is to press the insulation against the wall (mines rendered and is sound), tape all the joins and foam/tape/seal all the edges. Then put 25x50mm (standard roofing type) battens against the insulation, 25mm thick and screw the battens through the insulation and into the wall. Then plasterboard (normals fine but i would choose foil backed) to the battens and skim. This way seems to allow for the best vapour barrier you can achieve and u would have a void for cables without compromising the insulation/vb, and you could hang selves, pictures etc to the wall as you would any plasterboard wall without messing with the insulation and vb, and from what I can tell buying insulation and plasterboard separately would be cheaper also. (Window reveals would have to be dealt with differently) Can you see any downsides to this approach other than losing a few mm due to battens being a bit thicker than dot&dab. You input would be very much appreciated. All the best

@denisemc607 Жыл бұрын

Thank you thank you thank you! Excellent delivery, detail, and no faf. You are perfection ❤

@MtBArN 5 жыл бұрын

I do this on a daily basis. Well done!

@CharlieDIYte 5 жыл бұрын

Thanks mate - appreciate that vote of confidence from a pro!

@sarahknight4258 4 жыл бұрын

Superb - really on another level Charlie. Thank you.

@scottishpatriot5908 4 жыл бұрын

I worked for a double glazing and conservatory company a few years ago. We would always use kingspan as insulation. I remember it had a fishy smell when you cut it lol.

@RB-cs5dw Жыл бұрын

Amazing job m8, thank you so much. We are away to buy our granny's house as she passed away and I wanted to keep it in the family due to memories but it is a cold house, so was wanting to insulate all the boundary walls and this just looks amazing rather than messing about with wood and rock wool. Thank you

@georgenixon4608 2 жыл бұрын

Great video Charlie, clear and well presented. I have bought a villa in Spain with solid walls, and the rooms are COLD in the winter. I had thought about insulated plasterboard. Having watched your excellent video, I will be insulating the wall, so hears to a warmer property.

@CharlieDIYte 2 жыл бұрын

Thanks George. Before you do it, do lots of research on cold bridging and make sure you buy a board with an in built vapour barrier. Sockets and the edge of each board, corners and around windows are potential sources of cold bridging (cold spots) where condensation can form. And check out this video kzfaq.info/get/bejne/iq90lZChybXSiIE.html on keeping moisture levels down, though you may not have too much of a problem with that in Spain?

@ohyeahcristoff 8 ай бұрын

Great video - my old house has been cold for years - you've inspired me to sort it out uing this method!

@basilkearsley2657 5 жыл бұрын

Love the video, you make it look so easy. I have used insulated plasterboard in my garage conversion but found that the plasterboard came away from the foam and had to use lots of plasterboard screws to keep them firmly in place

@johnniewarren3049 5 жыл бұрын

Love how comprehensive your videos are a pleasure to watch look forward to seeing more of your projects

@CharlieDIYte 5 жыл бұрын

Thanks Johnnie! This one's been a beast to edit for one reason or another!

@simonruddy8265 4 жыл бұрын

Great vid thanks. My old 1900 house is a heating nightmare, you have given me a direction to move forward in future insulatiin works now. Thanks.

@Bradleyguy22 Жыл бұрын

For your suggested application it may be worth looking into a product called 'Spacetherm'. Much reduced (often 10x) thickness for similar U Value (W/m2k).

@jitsmen2519 8 ай бұрын

Excellent video Charlie! Im looking to do this in the summer time next year. Currently too busy with other renovation projects.

@JasonJFlippingLife 3 жыл бұрын

Thank you so much for taking the time to do this video and the one about relative humidity. I'm planning to purchase a property in Central Portugal where the older homes are notorious for being cold and humid during the winter. I now have a general understanding of how to tackle those issues.

@CharlieDIYte 3 жыл бұрын

Thanks Jason. And some sort of dehumidifier perhaps, or possibly a PIV?

@Bradleyguy22 Жыл бұрын

For your application it may be worth looking into a product called 'Spacetherm'. Much reduced (often 10x) thickness for similar U Value (W/m2k).

@robertsmart7484 Жыл бұрын

@@Bradleyguy22 But at a cost of about £100 per square metre it works out quite expensive.

@Bradleyguy22 Жыл бұрын

@@robertsmart7484 Hi, absolutely but in certain circumstances/properties the cost may be acceptable as it's the only method / cost effective solution etc but yes, it's not cheap.

@jeffjeffjeff2 2 жыл бұрын

Fantastic video, thabks for taking the time to record, edit and share. I'm going to tackle my front porch which is only a single skin of brick as it's the cold spot of the house and I was looking for recommendations for an insulated and moisture-proof board and this came up right away. I'll probably go with the batten fitting solution as I doubt it has anything in the way of moisure prevention currently. Thanks again.

@CharlieDIYte 2 жыл бұрын

Good idea. The thing to remember when you do this is cold bridging, cold bridging, cold bridging. This is the biggest problem when insulating from inside. A lot of care needs to be taken with window reveals corners and plug socket boxes - which ideally need insulating behind to prevent cold spots and moisture ingress. Good luck 👍

@mrflatroofer4089 4 жыл бұрын

Good video. Done this system 45 years ago. Still there.

@opentrail 5 жыл бұрын

Great video with lots of informative information and links. Love it. Is it a necessity to remove the gypsum-based plaster from the walls to install the boards or can they go straight on top without any issues?

@Jeff-gw1dv 5 жыл бұрын

Charlie brilliant video just what i needed as am going to do my small bedroom after having a steel girder fitted to extend kitchen dinner below so have ripped out old dob and dab plasterboard and will now fit the 50mm kingspan as the dobs on old ones were nearly 2" thick.!!

@CharlieDIYte 5 жыл бұрын

Thanks Jeff! It's great stuff, you won't be disappointed. It's worth getting a quote from SIG assuming they deliver in your area.

@padthai411 5 жыл бұрын

Ah this is the doc I was looking for thanks.

@itwillbenicewhenitsfinished 5 жыл бұрын

Glad this is back, it had dissappeared for a while. Great vid 😀

@CharlieDIYte 5 жыл бұрын

Thanks James! Glad to have finally uploaded it - this one's been driving me slightly mad 🤪

@footballsoccerreferee6152 4 жыл бұрын

Thank you for this amzing video Mr Chief DIY

@StAnger561to770 2 жыл бұрын

Awesome job mate! I wish I could do that here but my walls tend to be rather damp in this Old House and I don't trust the roof. It started to leaks in a few spots again, even after having all the clay tiles replaced a few months ago. I was able to get on the roof and sealed the leak spots but I'm not sure how long that will last. I don't mind running the heater in the winter more. I'll probably just stick to slapping some anti-mold paint up on these old walls and see if that does anything for me. Cheers!

@seannolan741 4 жыл бұрын

Never ever heard of a daughter turning the radiator half way down! :-) :-) :-)

@CharlieDIYte 4 жыл бұрын

Well, exactly, Sean!

@zorg1010tube 4 жыл бұрын

Great job, share the passion of DIY 😊 Thanks for very informative and great presentation. Subscribed👍

@bessbowers5533 4 жыл бұрын

Excellent job ! You are the most Professional of all DIYers out there.

@CharlieDIYte 4 жыл бұрын

Wow, thank you so much 👍

@Jcoughlan 4 жыл бұрын

Had a mate that retro insulated 5 houses like this except he used PU foam adhesive to adhere it to the wall. And mechanic fixings afterwards. PU adhesive is less likely to draw water through the wall. But you can’t use it to plumb the wall. Great if your walls are fairly flat and plumb to start off with.

@StAnger561to770 2 жыл бұрын

That pu foam has a good name because when i smells it I always say PU lol Seriously though if you have any damp issues that pu foam does eventually degrade, in my experience. Maybe not as fast as some silicone or other similar adhesives tend to though. Silicone is a lot easier to clean up though

@gelosul 5 жыл бұрын

Finally! I've been waiting for someone to do it and show how it's done just so I don't mess up.

@CharlieDIYte 5 жыл бұрын

You're welcome. Good luck with your project!!

@muniquri8210 3 жыл бұрын

Such a amazing video worth watching it you done to much research to make our life easier thank you

@maheshchauhan9290 2 жыл бұрын

Thank you Charlie. Like that you keep it real and sensible. 👍

@CharlieDIYte 2 жыл бұрын

Thanks 👊

@adamkhan5316 3 жыл бұрын

What an excellent video really. Brilliant information very well made, you cleared up a lot of confusion for me. I'm concerned about condensation on the back of the board though. It seems people prefer to mechanically fix for this reason. I wonder if anyone has anymore information for this.... personally I think the adhesives these days are incredible.

@CharlieDIYte 3 жыл бұрын

Thanks Adam. Yes, I mechanically fixed the last room I did and going forward I think this is a preferable option. You're right to be concerned about condensation, particularly where you're cutting through the board for the electrical back boxes. You want to aspire to creating an impregnable vapour barrier and continuous insulation to eliminate any cold bridging - which is damn hard in reality. In the bedroom I've just done, I battened the wall with 2x1 tanelised, dpc between the batten and wall where it touches - as the wall isn't level there was a nice gap behind. Then I infilled with 1 inch Ecotherm, foil taped over the joins, and then mechanically fixed the Kingspan to the front. That way, the electrical boxes only penetrate through the front insulation (I foil taped a piece of 12mm ply to the back of the Kingspan at that point to screw the back box to), and there's no cold bridging. Oh and I used that expanding foam tape you might have seen in that vid, underneath the Kingspan. It's breathable but eliminates any cold bridging.

@Ben.g 2 жыл бұрын

your garage looks similar to mine, would this method be good to use in that kind of environment ?

@gregnelson3006 Жыл бұрын

Thanks Charlie for the really useful info on your channel I have learnt a lot about insulating our home.

@CharlieDIYte Жыл бұрын

Thanks Greg, that's incredibly kind. Did you watch this update kzfaq.info/get/bejne/rt58rLqnl9zZeJ8.html sand keep an eye on my channel as I'll be doing another update on what I've decided to do in terms of insulating our kitchen. I'm thinking of going down the breathable route in there. Thanks again for the donation 👊

@normanboyes4983 5 жыл бұрын

Charlie that was excellent and very well worth posting.👍😀

@CharlieDIYte 5 жыл бұрын

Thanks Norman! Did you hear the shout out I gave you in my Parf system video kzfaq.info/get/bejne/mKeSl9Og38-ZY5s.html . I can't remember whether I forwarded you the link.

@tommiller7485 5 жыл бұрын

Hi Charlie, Thanks for this. Very helpful. Before applying the plasterboard - would you ever suggest plastering the stone wall first to increase insulation? Perhaps Lime Plaster if it’s a damp wall so the stone can breath?

@pedroroncon4554 4 жыл бұрын

Hi Charlie, great video! Just a quick question, how do you deal with the window molding? Can you just glue it on top or you need to secure it? Thanks

@garethb1968 4 жыл бұрын

You made a good choice doing this to your cottage , I been to jobs that other company's have insulted the lofts and stopped the air flow causing condensation in the roof space all they needed to do is add roof tile or slate vents

@mespabilo Жыл бұрын

Brilliant video, I've learned a lot and will be following it step by step to insulate the walls of my flat, thanks a million Charlie!

@CharlieDIYte Жыл бұрын

Thanks. Take a look at the foam adhesive too - it's a better insulator, and will be more effective to reduce cold bridging around the back boxes you have to cut out for plug sockets. Cold bridging should be your buzz word throughout the project. You need to do everything you can to eliminate any. 👊

@mespabilo Жыл бұрын

@@CharlieDIYte Thanks for that Charlie, is there a brand of foam adhesive you could recommend?

@robinford4037 4 жыл бұрын

Use a paint roller and tray to apply the PVA, load it up, start from the bottom and roll up, keeping a small wave of PVA between the roller and the wall, touch up with brush if necessary

@PaulHawxby Жыл бұрын

Great video Charlie. How did you get the radiator remounted? Did you have to extend the pipes or have you come up with some other way of doing it? Thinking of doing the same and trying to avoid having to drain down the system.

@samfox714 3 жыл бұрын

great help thanks - attempting mine this weekend!

@tanyaroyredcar 5 жыл бұрын

big thanks for your time and attention to this. Our walls are 3 bricks thick. Very dry. Considering mechanical fixing throughout though.. a longitudinal fixing of treated timber and then vertical fixing of softwood battening - to level. Fixing verticals with metal straps to reduce thermal conductivity - rather than timber to timber. Fill with fireproof insulation and screw fix 12.5mm plasterboard. Thickness 65mm internally. Wondering why you haven't gone for this approach, apart from the mechanics of getting it all aligned? with metal strapping, this has proven quite simple so far. Thank you R&T

@AranJackson 4 жыл бұрын

Hello mate. I didnt know you could dot and dab foil backed boards like that. Did you make any adjustments to account for that?

@bockersjv 5 жыл бұрын

Thank you thank you thank you. I have exactly the same walls with render on the exterior and they are always cold. This is just what I was after.

@davidrhodes6413 11 ай бұрын

great video, gave me some pointers that I hadn't previously considered. Thank you .

@CORRIGEEN71 4 жыл бұрын

Really really excellent video lots of detail and u don't have an asome American accent just brilliant have a whole house to do built 1937 mass concrete walls

@robandamyp 5 жыл бұрын

I'm a plasterer and I'd like to say very nicely done make sure you use a secondary fixing the adhesive is more like a packer I like to use 6 fixings more like a 6 on a dice than the way the manufacturer recommend but top job I've had lads working for me with years of experience that turn out worse boarding than that well done

@CharlieDIYte 5 жыл бұрын

Thanks so much Robert - I've got to say I was a bit nervous about posting this one but felt strangely compelled to do so - but comments from professionals like yourself are massively appreciated! Out of interest do you use the cork screw style mechanical (secondary) fixings I mentioned, or something else?

@robandamyp 5 жыл бұрын

@@CharlieDIYte I've tried many different types of fixing and to be honest I've never really been happy with any of them the insulation fixings are great because there all plastic but there about 5mm so skimming the wall becomes a pain I've settled on using a tile backer board washer with a zinc plated concrete fixing I have to make the hole in the middle of the washer bigger to let the screw head sit flat but it's the best I can come up with. most other options have either a small head so not really holding the board tight or othersare too thick to skim over

@CharlieDIYte 5 жыл бұрын

@@robandamyp Agreed. I thought about frame fixings (or the excellent steel core Corefix), rebated into the surface with a flat wood bit but being plastic they're not fire regs compliant.

@anthonymclean9743 5 жыл бұрын

@@CharlieDIYte Another tip which i always do is to drill a sequence of holes and stick the foam gun in for extra adhesion ..

@MarcGray1990 5 жыл бұрын

Got all this on the inside of my house on the external walls... just dabbed on.... I know it is meant to have mechanical fixings in an ideal world but it was done before I had the house and I’m not tearing it all off now haha. No problems as such just a few annoying movement cracks on the joints even with scrim tape on. So when going though the rooms decorating I’ve drilled small holes on the joints back to the brick and wet in the hole with diluted pva then foam filled to effectively stitch the crack. The stuff is as warm as toast in the winter and the heat wave last year nearly killed me inside haha!

@darylheasman1 3 жыл бұрын

Just a note, only use KNAUF bonding compound on foil backed insulation board k118 otherwise you are taking a big risk. There's no point in pva-ing the back of the boards then, knauf bags are readily available from all drywall merchants. When taking delivery of your boards lay them down as flat as you can get them especially if its going to be days before they get used to avoid them bowing.

@LB-gr5se 10 ай бұрын

What's the reasons for the KNAUF bonding compound? Thanks

@darylheasman1 10 ай бұрын

@LB-gr5se I assume your asking why use knauf bonding compound specifically on the knauf foil backed k118. If you use BG bonding compound instead,you will certainly run the risk of the board coming away from the dabs once they had set as it is not designed to stick to foil. Where as knauf adhesive you will have no such problems. On normal wall board, BG,Knauf or Siniat bonding are all pretty much the same ,though I personally prefer BG bonding. With Knauf ,you have to pay a little bit more attention when mixing because it doesn't like being overmixed by drill and tends to thicken up quickly, which you don't necessarily want if you have a large mix to do. Hope that answers your question

@LB-gr5se 10 ай бұрын

@@darylheasman1 that makes sense thanks for clearing that up

@qadeerhussain5751 3 жыл бұрын

Many thanks for your time & help

@Grayman58 4 жыл бұрын

Well done mate I am a brit living in canada and iam going to try your method on my son's bedroom because we also live in a 1920s house

@CharlieDIYte 4 жыл бұрын

Glad to hear it, Steve. Good luck. It'll make a massive difference.

@sonlyme4445 4 жыл бұрын

Remarkable that adding insulation to a property with no insulation requires Building Regs to approve it meets their spec. Does it meet their spec with no insulation? Jobs for the boys.

@CharlieDIYte 4 жыл бұрын

I agree!

@george9710 7 ай бұрын

Oh and if you think that’s ridiculous, consider that most local authorities charge you per external wall insulated. performance of the whole building

@Mikesay. 6 ай бұрын

Well said!

@matlovesrecovery 5 ай бұрын

I’m doing mine and not telling them it’s for my benefit.

@airjaff 4 ай бұрын

Screw telling them. how would those a-holes know!

@geowgeow Жыл бұрын

I love your videos Charlie. It’s been 3 years since you did this. Have you experienced any condensation issues or signs of condensation forming behind the insulation? I’m keen to do this at my house (already done one room) but my head is spinning with all the conflicting advice around the condensation risks and lack of breathability. This stuff is BBA approved for this application but there are so many experts warning against doing it at all or recommending alternative, breathable panels combined with lime plaster to maintain the breathability of the building. Interested to know your thoughts/experience on this

@thewalkingsketchbook Жыл бұрын

I’m having the same conundrum, George! Victorian building so 9” solid walls. We had some damp on one wall already but a specialist said it was mainly due to the incorrect mortar used when the pointing was re done some years ago. Replaced with a proper lime mortar we haven’t had many issues. But if I insulate with this method, am I adding to moisture/breath ability issues?

@mrat42 11 ай бұрын

@@thewalkingsketchbookmy house has solid brick walls and I insulated the walls internally 40 years ago. There was not much information available. Some was very wrong. I was concerned about condensation in hidden away spaces.I had a choice of polystyrene sheet or fibreglass/ mineral wool. I used the latter as it was much cheaper. I made a frame of 50 x75 mm tanalised timber, screwed to the walls and filled with insulation. Then a polythene vapour barrier and then plasterboard. Keep the vapour barrier intact around power sockets was awkward. I’m still in the house and have had no issues. I have one last wall to insulate, the bathroom. It’s only a few m2. No external render. But it’s sheltered and I might bond directly to the wall. Still in two minds about it. 24:19

@lozbian68 8 ай бұрын

@@thewalkingsketchbookthink of it like this , your house needs to breathe hence the lime mortar outside and the same applies to the inside with regards to lime plaster and limewash/ breathable clay paint , this method will keep humidity controlled in your property and won't end up spoiling any brickwork because of a build up moisture 👍

@supersesqui 4 жыл бұрын

Another informative and well done job. cheers

@johngarbutt 3 жыл бұрын

Brilliant. Quite a bit of work involved but you show us all the way very well.

@CharlieDIYte 3 жыл бұрын

Thanks John. The important thing is complying on the u value front and preventing any cold bridges. Plug sockets can be problematic as you're often cutting all the way through the insulation.

@MadDogsVlog 4 жыл бұрын

Hi, What fixing should I be using to hang mirrors, curtain rails & picture frames on 50mm insulated plasterboard?

@CharlieDIYte 4 жыл бұрын

Fisher Duopower would do a good job. For the heavy stuff you could use wall anchors - probably 5x52mm. They work in insulated plasterboard as the umbrella forces itself open even in the insulated foam. The only downside is that the screw head on the bolt is reasonably large, or at any rate looks different to a screw. kzfaq.info/get/bejne/m5mYnd2Bs8uZp58.html

@wilyc0y0te 2 жыл бұрын

Coming to this one quite late. Another really high quality video - great explanations. One thing though, these boards are phenomenally expensive now. In my 100 year old semi, it’d cost approximately £1000 for the materials to do less than 2 of my first floor rooms (external walls only, 50mm board). Have any competing products been released since this video was first uploaded?

@MadDog_Rules 2 жыл бұрын

Before you carry out any work, make sure the house does not contain any asbestos. Also old houses with plaster walls would highly likely have no vapour barrier under the plaster to stop moist air from saturating the insulation. Back then, plaster walls were designed to allow the free exchange of air and moisture. If you're not sure if the plaster has been replaced with a vapour barrier or any insulation, remove a small area and check. You may just need foam or wool insulation and a vapour barrier underneath the plasterboards. I can highly recommend Tekwarm EPS HP, not sure if it's available where you live though.

@AccountantDoesDIY Жыл бұрын

Sadly this is just the way of the world now. Building material costs are significantly higher than they were in 2019 when Charlie did this video. It’s been a painful three years for us DIYers !

@UnleadedApe 3 жыл бұрын

Thanks Charlie, gonna give this a go soon!

@CharlieDIYte 3 жыл бұрын

You're welcome. Just be careful with the plug sockets. Cutting the board does create a cold bridge. If you're going to dot and dab like I did and need to fit back boxes, rather than adhesive all round the socket, I'd get the back box ready, with a wall plug drilled in the wall to fix it in position, and then spray expanding foam in the gap behind the back box and quickly fix the box in place so the expanding foam expands and hardens around it. That will pretty much eliminate any cold spots that could cause condensation in this area.

@harrycallaghan22 5 жыл бұрын

Excellent tutorial. Great stuff.

@CharlieDIYte 5 жыл бұрын

Thanks!

@P12NCE 4 жыл бұрын

Hi Charlie, I’ve only just seen this video even though it’s almost a year old. I insulated the external walls in two bedrooms of my house the difference it makes is amazing. In one of the rooms I hacked of the plaster as it was very loose, but then I put a tight coat of sand and cement to get rid of some of the bows and bellies in the wall. Around the windows I framed them with 2x2 batterns. Before putting the boards up around I cut away the insulation only. When you put the board up around the window you can screw the edges around the window. Around the window you now have a reveal which you stick standard plaster board to using screws with a few dabs of adhesive. I’m about to move on to my bathroom. I just concerned about the condensation, and of course the tiles on that wall. Any advice

@satwinderdhariwal 2 жыл бұрын

Don't you lose heat around the standard plaster board on the window edges

@P12NCE 2 жыл бұрын

@@satwinderdhariwal I don’t think so. Around the window is framed with two by two and inside that it is insulated. I realise you will loose some heat but it is a vast improvement, which is what you want at the end of the day.

@GretatheEvilGremlin 5 жыл бұрын

Great stuff, clear and concise. Good to see building control nonsense tamed. It’s all a game to take things out of the hands of DIY and drive the contractors market. Look where cavity wall insulation got us !

@CharlieDIYte 5 жыл бұрын

I think you're absolutely right. And a builder mate said to me the other day when I told him I was preparing this video that in his experience these guidelines are often not followed!

@clivewilliams1406 5 жыл бұрын

Nonsense! The Building Regulations are the MINIMUM standards that have to be achieved and there is nothing apart from Heating and Electrical work that requires any recognised trades certification and therefore within the scope of a DiY'er. If you had seen the vast quantity of botches I have witnessed from both unknowledgeable amateurs and supposedly skilled tradesmen there is a case for more stringent application of the rules rather than less. The Building Regulations came out of the numerous local Public Health Acts that were brought together under a consolidating document, and without them we would still be victims of the Victorian slums. The Building Regs are continually evolving as they play catch-up with modern standards and innovation, the problem is that they are dealing in an ever more technological world so a becoming more prescriptive than performance based.

@CharlieDIYte 5 жыл бұрын

@@clivewilliams1406 I'm sure what he meant by "building control nonsense" is that the way the controls have evolved (and as you say, it's difficult to blame them for this as they play catch up) means that it's difficult for the average home owner, about to embark on a project, to make sense of.

@GretatheEvilGremlin 5 жыл бұрын

Charlie DIYte There’s a lot to cover so I shall keep it brief(ish). I did a self build 20 years ago when things were still quite normal, and it was a pleasure to do. Now we are being turned into cash machines and it’s like Dick Turpin has written the building regs. Advanced they maybe, structured robbery it certainly is. All backed and influenced by Gypsum, Knauf, and all the rest. Replacing boilers at £2000 a pop, for something that’s going to break within 5 years. You don’t really get your money back! Electric consumer units seem to be changed more than underpants, that’s just making money out of people. Becoming an eco warrior has some merit, but it’s only forced and driven by the extortion of energy companies. Older property needs to breathe, and the funny thing is it’s already stood the test of time for there not to be an argument that it was built right in the first place. New builds I wouldn’t have given, and I could cry myself to sleep for the amount of ‘quality apartments ‘ I have inflicted onto the great British public. May the Lord have mercy on my soul.

@Tayuss79 3 жыл бұрын

Nice job seems like I could give it a go. Worried about water penetration though. No render on the outside of our cottage. Seems very worth taking on anyway.

@fueltoblaze1554 Жыл бұрын

Thank you! We have just done this to our kid's room from your instructions.

@CharlieDIYte Жыл бұрын

You're very welcome. Glad you found it useful and thanks for the comment 👊

@ivanbarritt7650 3 жыл бұрын

Hi Charlie, great video thanks. Just a quick question...... When you mark the walls and ceiling so you can align the plasterboard panels, do you have to take into account the depth the adhesive will bring the board out by? Hope that makes sense👍

@CharlieDIYte 3 жыл бұрын

Yes, you want the lines to be a finished depth guide. Otherwise you won't see them because the adhesive will bring the boards forward of the line you've marked.

@grumpy9250 3 жыл бұрын

I would be interested in how you tackled the window reveal.

@yourkodi3945 3 жыл бұрын

would be great to know this

@elltell8644 3 жыл бұрын

a normal 12.5mm plasterboard would be used.

@alexclifford8961 3 жыл бұрын

@@elltell8644 followed by damp and mould in the months to come. Needs a proper thermal break. the improved insulation on the rest of the walls increases problems in the remaining cold areas.

@elltell8644 3 жыл бұрын

@@alexclifford8961 with window profiles of 30 - 40mm there is little else that can be used other than 12.5mm foil back boards. how they are fixed is down to the operative.

@Philsy1845 Жыл бұрын

Retired builder good demo Charlie. No rambling tech waffle nice straight down to brass tacks! Many rather pay its still a tough job ok if fit and enthusiastic!

@CharlieDIYte Жыл бұрын

Thanks Phil, I appreciate that. There are things I'd have done differently (like use the foam instead of the adhesive) but I covered as many bases as I could. 👊

@Ratsotone 2 жыл бұрын

For a DIYer you're very thorough, and you put a lot of professionals to shame...An excellent informative video.

@CharlieDIYte 2 жыл бұрын

Thanks buddy, I really appreciate that. 👍 For videos like this straying from DIY into building work you have to be on your game or you get shot down in flames 😉

@Ratsotone 2 жыл бұрын

@@CharlieDIYte and more often than not, the ones who criticise are the ones who cut corners to save time and money. They might be able to talk a good job, but it stops there, I've come across those types so many times.

@williamarmstrong7199 4 жыл бұрын

The big question we all need to know is... how did you get a teenager to keep her room that clean? You can actually see the floor!

@bali2880 3 жыл бұрын

Lol 😂😆😆😆

@mcspad 4 жыл бұрын

Those boards need fixings foil backs always pop off dabs

@leicestershirejim1558 3 жыл бұрын

Very helpful and interesting video. Thanks.

@Cradley684 5 жыл бұрын

Great job Charlie !!!

@CharlieDIYte 5 жыл бұрын

Thanks Brian!

@chrise202 5 жыл бұрын

I wish this method was banned. It eases the builders job but its a total pain in the ass for the homeowner when it comes to DIY. Prefer the studs

@mrcaboosevg6089 4 жыл бұрын

I've spend many hours rebuilding studs in my 200 year old house to get things level, this looks like a much preferred option. Not a single wall in my house is square and it's a right pain in the arse doing it 'properly'

@CharlieDIYte 4 жыл бұрын

I've just done my bedroom wall the stud method, and my bathroom before that. It was more of a pain but I thought I'd do a video on it, and also, with that extra layer I've more than complied with building regs in terms of the u values.

@riboid 4 жыл бұрын

Banned? Ok.

@seanoxborough8595 5 жыл бұрын

Bond the back of a board before sticking??? My arse, what's the point?

@MrDannybey 3 жыл бұрын

Pva on the back of the board isn’t the thing to do. You can buy the correct board. I think it’s called pl4000. It’s got paper on the back not silver!

@MzLewis29 7 ай бұрын

Thanks so much. Our walls are the same, and we're in need of better insulation as well.

@trimley 2 жыл бұрын

I learnt so much from your video and I’m in the building trade!

@CharlieDIYte 2 жыл бұрын

David that's incredibly humble of you, and I say to any trade pro who comments favourably on my vids (eg the silicone one) that they're clearly very good at their job. We're always learning aren't we. Actually there are a few things I'd do differently since making this. On my most recent bedroom refurb to eliminate any potential cold bridging (sockets being a big source) I battened the wall with 2x1, infilled with 1 inch celotex PIR, foil taped over the battens and then screwed the K118 insulated plasterboard to the battens. Socket boxes were cut though the insulated board with a 12mm ply board foil taped to the back to screw the box to. That way there's no cold bridging though the socket. Also continuous insulation around the window reveals and breathable expanding foam tape under the insulated plasterboard. And I either didn't video it or I've lost all the footage 🤦🏻‍♂️ Thanks for the comment 👍

@davidskeeterskeeter1835 5 жыл бұрын

😂😂😂😂😂😂 WTF are you doing fella,!, ABSOLUTELY no need to remove the old plaster 😂😂😂,! You took more time removing that old crap,,than fixing your boards,😂😂 Just drill through your insulated plasterboard AND the old plaster and (mechanically fix)using Fischer POLYPROPYLENE fixings to brickwork ,,12 fixings to each board,, Before you all start jumping up and down 😤I have been using this method for 28 years,!, my company has renovated more than 300 properties , I in fact still own 147 of these houses,as a private landlord,, PS,, very little point in applying pva directly to substrate that appears to contain old lime plaster,, PPS, I’m 73 years old started plastering at 14 I sincerely hope this has been of use to someone,👍🇬🇧

@CharlieDIYte 5 жыл бұрын

Three reasons 1) the plaster below was live and I didn't want to just hide it behind the new board (a botch in my opinion); 2) the walls weren't true - years of badly applied irregular plaster - so mechanical fixings wouldn't help with this; and 3) the wife is annoyed enough that I'm reducing the size of the rooms with this insulation so I was wanting to keep this to a minimum. I hear what you say that your approach is a lot less hassle though. Are the polypropylene fixings fire regs compliant? I thought they had to be metal.

@geoffreycasey875 4 жыл бұрын

@@CharlieDIYte you can get metal ones which are much better. 🍀

@daveMCZ 5 жыл бұрын

It isnt a good idea to insulate from interor of the house... exterior is much better - u save the materials before destruction via water x freeze. once u insulate inside part - u shift zero ceslcius into the brick (water start to change into ice - expands and destroys the material, u are never able to restrict all af vapore to come inside the material). ... if u insulate exterior part of the wall... proper thickness of insulation will have zero celsius in itself...... PVA is supposed to be used , once u clean the wall properly :) it doesnt take such a lot of a time and effort :)

@mattivirta 5 жыл бұрын

external insulation need be water resist, not suck water newer, only closed cell foam can use external insulation, interior can use all other, but not bathroom and water area rooms.or rooms were have sometime steam.

@MrJohnnynapalm7 3 жыл бұрын

Really good and detailed video - thanks for sharing 👍

@CharlieDIYte 3 жыл бұрын

You're welcome. Thanks for the comment. 👍🏻

@allisonjoel1 3 жыл бұрын

Excellent video. Thank you for sharing. I had insulation boards put on two walls in my kitchen and on one wall in my bathroom by the Housing Association I am under several years ago. To my surprise they put the boards over plastered walls. Since then, I have encounter problems with mildew around the top and edges of the boards and think part of the problem might be that they haven't been sealed correctly.

@CharlieDIYte 3 жыл бұрын

Yes that'll be because of cold bridging. Take a look at this video kzfaq.info/get/bejne/iq90lZChybXSiIE.html It's important you have some ventilation in your place during the day (windows open if you can) just to let out the huge amount of moisture we generate daily

@marcvoss3204 4 жыл бұрын

Good video. Some great ideas there . Well done Charlie. I’ve subscribed 👍👍👍👍

@CharlieDIYte 4 жыл бұрын

Thanks Marc!

@thomasjbyrne1 5 жыл бұрын

As usual - fantastic video!

@CharlieDIYte 5 жыл бұрын

Thanks Thomas!!

@arifanwari3168 3 жыл бұрын

I find a shovel and brute force works and it's quick for removing old Browning/render/plaster 🙂

@mr1379 5 жыл бұрын

Excellent video. Very detailed.

@CharlieDIYte 5 жыл бұрын

Thanks - just about killed me editing it so I'm really glad you liked it!!

@jmtworm 3 жыл бұрын

Great video Charlie, cheers

@borodinskyful 5 жыл бұрын

Great vid and nicely done

@08vinster 2 жыл бұрын

Thanks for this video. very useful

@harpo187bling 5 жыл бұрын

Nicely done pal.

@reshlanda1964 2 жыл бұрын

What a very informative and detailed vlog

@CharlieDIYte 2 жыл бұрын

Thanks. Glad you found it useful.👍

@aleksandrabogusz4653 3 жыл бұрын

I am loving it

@simoncooke6881 3 жыл бұрын

Brilliant video - really helpful!!! Thanks

@CharlieDIYte 3 жыл бұрын

Thanks Simon. The only thing I'd add is be careful with the electrical back boxes. Probably best to spray foam behind them to eliminate any cold bridging, if you can. 👍🏻

@duncanblanchard334 3 жыл бұрын

Great video, the issues for me would be the wires for sockets wouldn’t be long enough to reach through the new insulation, and pipes for radiators not reaching, it would be a massive job. You made a good job of this, just measuring for the sockets would of taken all day for me 😂.

@RandomShart Жыл бұрын

Wires for sockets you can easily extend with wago or similar. As I hate all plumbing I'd agree radiators would be a pain but no doubt would be a very easy job for a plumber to just extend the pipework. Given my gas has just gone from £110 to £600 a month this year I think it's worth a punt!

@Love500 2 жыл бұрын

Really useful. Thank you. I intend to do my conservatory in the new year.

@CharlieDIYte 2 жыл бұрын

Glad to hear it. If you have to install back boxes for the plug sockets, try not to cut all the way though the insulation or if you have to, re-insulate behind with spray foam to minimise any cold bridging. You could even glue the insulation boards in place with spray foam rather than plasterboard adhesive. 👍

@Love500 2 жыл бұрын

@@CharlieDIYte really? That would work? Probably easier. I’m always worried about making the plaster too thin. Thanks for the tips.

@forpeace8375 3 жыл бұрын

Thank you for this KZfaq video 👍🏻 Can DIY now

@CharlieDIYte 3 жыл бұрын

Thanks. 👍

@AmZPresents 5 жыл бұрын

Great video. Can you please upload video of the best plasterboard fixings, plasterboard with insulation. I saw many videos for plasterboard only but most new builds have insulation and wanted to know which one will be best.

@muniquri8210 3 жыл бұрын

Such a amazing video worth watching it thank you

@CharlieDIYte 3 жыл бұрын

You're very welcome. Thanks for taking the time to comment 👍