How To EASILY Repair Holes In Aluminum

Рет қаралды 1,546,166

10 жыл бұрын

How to easily repair "fix" holes or cracks in aluminum sheets, plates, tanks, and pots using a quality aluminum brazing rod like Alumite brand. Using a clean stainless steel brush just before initial brazing is essential for excellent results. Not removing oxidation/corrosion will result in a very poor repair.
Alumite & Alumaloy brazing rods BOTH work great. Please refer to the link posted below if you're interested in purchasing these rods:
amzn.to/2o4JaVx
electronicsNmore is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for this channel to earn fees(which support my work) by linking to Amazon.com and affiliated sites.”
My other excellent aluminum repair video is here:
• How To Easily Join Tog...
Support this channel by using the link below:
paypal.me/electronicsNmoreYT
**For GREAT deals(Usually cheaper than EBAY) on electronics, drones, automotive, home goods and MUCH more, please visit the link below. Your purchase supports my channel.
All Items: bit.ly/2cgYr14
Flash Deals: bit.ly/2cb6CZB
*Try these money saving coupon codes: affiliate6 or aff7off or f8aaf1 or 781622 or 5719ed or elec* or ask if other codes are available!
Thanks For Watching!
**If you enjoy watching my videos, please show your support by SUBSCRIBING, POSTING LINKS to my videos on other websites & blogs, rating a "THUMBS UP", and watching my video playlists. Doing so helps to ensure that many more videos will be released in the future. (Views are essential to ensure this channel remains in an active state)**

Пікірлер: 384

@electronicsNmore 6 жыл бұрын

**For GREAT deals(Usually cheaper than EBAY) on aluminum brazing rods & flux, test equipment, electronics, drones, automotive tools, household items, phone accessories, locksmith tools, & much more, please visit the link below and SAVE IT AS A BOOKMARK on your computer or smartphone to Banggood for future purchases. (Your purchase supports my channel!) All Items: bit.ly/2cgYr14 Flash Deals: bit.ly/2cb6CZB **Try these money saving coupon codes, or ask if other codes are available: 6% off everything: affiliate6 12% off Home & Garden: BGHome 12% off electronics: elec or measure 8% RC Toys & Hobbies: ToysHo

@emiliomejia2676 6 жыл бұрын

can you drill through the aluminum that you cover the hole?

@SameerKhan-yz3it 5 жыл бұрын

electronicsNmore tttffgreesdđsd

@jurgeenhandazola3006 7 ай бұрын

¿How strong is that fix against heat? ¿Can it whistand car engine heat?

@BigDaddyMuddzy 8 жыл бұрын

worked great for me on 1/8" hole in aluminum canoe. I did it in the sun - the aluminum was thin and ambient temp was 70 but the canoe was probably about 100 degrees from the sun. Used yellow propane bottle and the whole project only took about 30 min - including cleaning aluminum, heating and brazing hole, grinding and cleanup. I'm sure with thicker aluminum and/or a bigger hole it will take more time. THANK YOU very much for posting the video!!!!

@electronicsNmore 8 жыл бұрын

You're welcome! Be sure to share my channel with others and rate thumbs up. Thank you.

@mobilecarwashcorp8235 7 жыл бұрын

Thanks for this lesson. You saved me a ton. Keep up the good work. I really liked this technique!!! Worked flawless.

@electronicsNmore 7 жыл бұрын

Glad you enjoyed the video Ken! Be sure to rate thumbs up, share with others, and check out my video playlists. Thanks

@SirHenryofRR 8 жыл бұрын

Even though I will be using mostly oxy acetylene this has been most informative. Keep up the good work.

@gonefishing5415 6 жыл бұрын

great tip, thanks. Keep sharing your experience.

@GalaXy808 10 жыл бұрын

This is good, thank you much!

@renosoler6232 4 жыл бұрын

Thanks for this video, this is what I am looking for. I've learned it.👍

@electronicsNmore 4 жыл бұрын

You're welcome! Be sure to look over my extensive video playlists below for many other videos of interest to you, and share my videos on social networking websites. Thank you kzfaq.infoplaylists

@acklan3 9 жыл бұрын

I did a similar repair several years ago. I preheat the pot (Magnalite) in the oven to 400*, to minimizing the heat sinking problem. Then I brazed the crack. Once finish I placed it back in the oven and turned it off. Let it cool down over night. Still using the pot to this day. Good video.

@electronicsNmore 9 жыл бұрын

Slow heating and cooling is the best method. Thanks For Watching! Be sure to share and rate thumbs up.

@gennarobarba7396 7 жыл бұрын

greetings from Canada...great and useful video, THANKS!

@electronicsNmore 7 жыл бұрын

Glad you enjoyed the video! Be sure to check out my extensive video playlists, rate thumbs up, and share. Thank you

@SouthernRancher13 28 күн бұрын

I did this to my aluminum boat seems solid and i also coated over it with Flex steel super slick! wish me luck!

@GoAndStay 8 жыл бұрын

Thanks. I learned a lot

@electronicsNmore 8 жыл бұрын

You're welcome! Be sure to share. Thanks

@dudebro9825 8 жыл бұрын

Really solid amount of information, clear concise and to the point, didn't leave anything unanswered!Im gonna be using this technique to fill some small 1/8" - 1/4" holes in my jon boat, and sealing my rivets for next duck season. THIS IS WAY BETTER THAN SENDING IT OFF TO A WELD SHOP AND SPENDING $100 USD

@electronicsNmore 8 жыл бұрын

+M Thom Glad you enjoyed the video! Just make sure the surface is SUPER clean using a grinder followed by a stainless steel wire brush.

@charliehatfield6399 5 жыл бұрын

Excellent tutorial ! Thanx .

@electronicsNmore 5 жыл бұрын

Thanks for watching Charlie! I have a lot of excellent videos on my channel that cover many different subjects, so be sure to check out my extensive video playlists for other videos of interest to you, rate thumbs up, and share my channel with others.

@cuellargabier25 9 жыл бұрын

Thanks for sharing your video and your valuable advice.

@electronicsNmore 9 жыл бұрын

Gabier Cuellar Glad you enjoyed the video. Please share my channel with others, check out my other videos, and rate Thumbs Up, Thank You!

@DoctorCreepy 5 жыл бұрын

Very cool thanks for sharing.

@electronicsNmore 5 жыл бұрын

Glad you enjoyed the video! Be sure to rate thumbs up, share, and check out my extensive video playlists for other great videos of interest to you. Thanks

@penny6735 3 жыл бұрын

Great video! SO helpful. I'm wondering will this repair will withstand the heat from a very hot wood burning stove. (its an old aluminum tea kettle with a hole a little bigger than a pin hole).

@electronicsNmore 3 жыл бұрын

As long as there's always something in the pot, it will hold.

@miguelreyes8466 6 жыл бұрын

Thanks for sharing

@Lanninglongarmmowing 9 жыл бұрын

Great video. I don't remember seeing this video when I was doing my aluminum boat repair. I'm still waiting on warmer weather to get back to it. Lol.

@electronicsNmore 9 жыл бұрын

Hey Nick. Yes, I added this video after the other one was uploaded. Have a nice New Years!

@Lanninglongarmmowing 9 жыл бұрын

electronicsNmore oh ok. It works better with thicker aluminum because its not able to warp as easily. Have a great new years also!

@sazzadhossains4329 3 жыл бұрын

Nice & good work policy.

@Iddragon 4 жыл бұрын

yeah i feels good knowing somebody can helpyou

@fireandcopper 5 жыл бұрын

I was going to use the oxy Mapp torch, but the adjustable ts-8000 with propane seems better. Hank would be proud.

@geojor 9 жыл бұрын

thank you...

@robbiehobbs2009 7 жыл бұрын

That is some serious exacting heat application to pre heat and fill that hole WITHOUT burning thru. And the material seemed to magically fill in. looks like you've had some practice.. Very well done. I have a aluminum water tank in my boat that doesn't leak yet but I want to fill some pitting before it eats thru. Going to try and apply your lesson. Thanks

@electronicsNmore 7 жыл бұрын

Hi Robbie. Just make sure the area is SUPER clean(bright and shiny), and only apply enough heat to get the brazing rod to melt when touched to the aluminum surface. You'll likely need to use a MAPP gas torch. BTW, nice Gag Grouper. I freedive & spearfish. I've blasted some big ones too in the past.

@guliyevshahriyar 2 жыл бұрын

Thank you for helpinh us

@eadghe 11 ай бұрын

Thanks for the informative tutorial! Could you please tell me how to handle dents in aluminium pots, such as pots for outdoor activity? I read the aluminium must be heated as well, so the material can be reshaped. Or is that not needed with thinner aluminium? I'm pending between dealing with the dent and the dented bottom or going for a fix. I'm afraid I might weaken the overall material.

@ismailaiyub2173 3 жыл бұрын

Thanks alot very useful ideas.

@electronicsNmore 3 жыл бұрын

Glad it was helpful! Be sure to check out my wide range of videos below, and most importantly share links to my channel with others. Thank you kzfaq.infoplaylists

@RestoreItAll 7 жыл бұрын

great video , I just thought of one thing, You could reheat the pot or surface with a heat gun .

@digitaldoc1976 2 жыл бұрын

You solved a problem on which I have been working for three years in less than 6 minutes. Thank you.

@electronicsNmore 2 жыл бұрын

Thanks for watching Luke!

@jeevunvethanayagam6536 2 жыл бұрын

What problem did you have?

@digitaldoc1976 2 жыл бұрын

@@jeevunvethanayagam6536 I have a pair of Hartley 24" Concertmaster speakers which have had the aluminum pit horribly. They are quite valuable and incredibly rare and collecible. The foam surround disintegrated over the decades. This brought them to within 20% restored. Thank you!

@AG-yj1jv Ай бұрын

Can this be used to repair the aluminum clad bottoms on old 1950's Farberware pots (stainles steel food side, aluminum outside). My cousin had the fry pan for years & it's eaten out in places

@maynardcat 9 жыл бұрын

I'm glad you uploaded this video I have a big tea kettle with a tiny hole in it I need to repair, before this video I couldn't see anyway to repair it and still be able to heat it.

@electronicsNmore 9 жыл бұрын

maynardcat As long as you clean the area extremely well using a stainless bristle brush, and do not apply too much heat, you will be able to repair the area. As you heat, keep testing the temp of the pot by touching the brazing rod to the pot, when it starts melting, pull back and maintain that level of heat! The initial filler needs to be brushed into the surface when molted before applying the rest of the brazing rod. When cool, file, or grind to shape. Thanks For Watching! Be sure to Share and rate Thumbs Up.

@maynardcat 9 жыл бұрын

electronicsNmore Thanks for the advise, it's an old tea kettle from the late 40's or early 50's so it's worth saving, and now I can with your advise.

@Matsci101 6 жыл бұрын

I always heat the Aluminum and the rod at the same time. Its cool stuff if you learn how to use it! One can also make a dam with sheet metal to fill in large areas, I did it to a corner on a timing chain cover. BTW I also can gas weld 308 Tig rod on stainless! I am not a welder!

@fredmertz9950 2 жыл бұрын

Very nicely done.. the surface tension of the aluminum keeps it from falling in ?

@electronicsNmore 2 жыл бұрын

Pretty sure that's why it doesn't fall in. Thanks for watching!

@jimbola77 8 жыл бұрын

cool tip!!!!

@jamalbadhafari2634 6 жыл бұрын

nice job 👍

@electronicsNmore 6 жыл бұрын

Glad you enjoyed the video! Be sure to check out my extensive video playlists for other great videos of interest to you, rate thumbs up, and share. Thanks

@harrynasution4172 5 жыл бұрын

nice job bro...

@electronicsNmore 5 жыл бұрын

I have a lot of excellent videos on my channel that cover many different subjects, so be sure to check out my extensive video playlists for other videos of interest to you, rate thumbs up, and most importantly share my channel with others. Thank You

@tellmesomething2go 8 жыл бұрын

Very good work. Liked.

@electronicsNmore 8 жыл бұрын

+Arthur Bradley Thanks Arthur. There are lots of excellent videos on my channel. Please be sure to share, and check out my video playlists.

@MrTarkus007 8 жыл бұрын

didn't know that you could do aluminium welding with just a little propane torch very nice .2nd question after sanding down metal for prep can you use acetone for cleaning ? metal to be sure ? by the way liked your vid .

@electronicsNmore 8 жыл бұрын

Hi Mario. No need to clean the aluminum with anything but the wire brush unless the metal is oily. Thanks for watching!

@TrevorFisher 8 жыл бұрын

Could you use this pot (and particularly the weld spot) over an open flame (say a propane burner) after it cools and sets? Or would the weld fall out? My turkey fryer pot has a hole in it and I'd like to repair it. But if I can't use the pot on the fryer propane burner after repairing it then it doesn't help me much.

@tellmesomething2go 8 жыл бұрын

+Trevor Fisher The moral here is: never get a hole in your pot. Pologise.

@abdulkadir-iv9gc 2 жыл бұрын

Great work 👌👌👌

@electronicsNmore 2 жыл бұрын

Thank you!

@TheLandlordPicker 6 жыл бұрын

Looks good. I was looking for a video for repairing a hole in an aluminum pontoon. I think ill practice with a few pieces of aluminum first. Really appreciate the video it was done well.

@electronicsNmore 6 жыл бұрын

Part-Time Picker The only problem is you'll need a lot of heat to work on a large, thick area of aluminum......maybe easier to buy a small piece of aluminum plate and rivet it to the boat over the hole with 3M 5200 marine adhesive applied. Fill in the rivets with the 5200 also. If the hole is very small, just wire brush the area really good, wipe down with 91% rubbing alcohol and use only the 5200.

@TheLandlordPicker 6 жыл бұрын

electronicsNmore i use map gas when I am soldering copper pipes do you think that would work? That gets much hotter than propane? Also it only appears to be two pinholes. On the front of each pontoon. Probably from hitting / gliding up on rocks on shore. I actually just thought about drilling the hole a little bit larger and filling them with silicone. It only has to float on top of the water. No pressure really. Any thoughts?

@electronicsNmore 6 жыл бұрын

Part-Time Picker Wire brush the area until super clean, wipe down with alcohol, and use the 5200. Press into the holes and smooth with a wet finger....it will last years.

@TheLandlordPicker 6 жыл бұрын

electronicsNmore 5200?

@electronicsNmore 6 жыл бұрын

Part-Time Picker Look it up 3M 5200.

@stefanBEAR98 6 жыл бұрын

are these aluminum rods stiffer than copper rods of equal gauge?

@Almostboosted 6 жыл бұрын

Great job

@electronicsNmore 6 жыл бұрын

Almost boosted Thank you!

@md.muneer9944 6 жыл бұрын

Goob job man

@c.t.u3718 8 ай бұрын

Hi, what type of rod is used in aluminum brazing?

@quetzalcoatldeuz8912 10 жыл бұрын

nice!

@pikifrino 7 жыл бұрын

Once again, thank u

@electronicsNmore 7 жыл бұрын

You're welcome! Be sure to rate thumbs up, check out my video playlists, and share my channel with others. Thanks

@towerh6680 4 жыл бұрын

I plan to use your technique on an aluminum crab pot that has a couple pin holes in it....but what is stopping the brazing rod material from re-melting (then exposing the holes) when I put it on a propane burner????? Thanks for helping

@electronicsNmore 4 жыл бұрын

As long as there's liquid inside the pot, it will never melt out when over a flame/burner. :-)

@Jeweljasmine1 7 жыл бұрын

Could u use a similar technique to repair a leak in a pontoon on a pontoon boat?

@electronicsNmore 7 жыл бұрын

Aleyia Phoenix Yes. Make sure you can supply enough heat.

@Jeweljasmine1 7 жыл бұрын

electronicsNmore perfect thanks

@reinaldodasilvavaz5251 8 жыл бұрын

Onde eu encontro esta vareta de solda,será que os brasileiros terão acesso a esta tecnica . tankyou

@9sec93lx 8 жыл бұрын

Seems to me that you could have saved a lot of Propane by placing the large Aluminum pot in a 500 degree oven first to preheat the whole item. Then it won't suck away all your heat so fast. You do the same thing when repairing Cast Iron items to prevent thermal shock. Cast Iron actually needs to be put back in the oven after the repair so it can cool slowly and lessen the chance of it cracking and spoiling your repair job.

@electronicsNmore 8 жыл бұрын

Best Racing Tips Win At The Dragstrip I have used that technique before. It does work very well. Thanks For Watching!

@philipbrailey 5 жыл бұрын

Best Racing Tips Win At The Dragstrip What happens if you have a bigger job do you wanna buy a big oven.

@juzdoitbtcrandom3717 5 жыл бұрын

S'all gud man he looks lyk his rich...... with propane gas i mean..

@magogon70 6 жыл бұрын

Great...Would this work to weld the new f150 aluminium body ?

@electronicsNmore 6 жыл бұрын

Works on all alloys of Aluminum. Thanks for watching!

@koepketube 10 жыл бұрын

That's hot ;) Darn it ENM, now I have to order these things... So what if I never get around to using them xD

@Farmer2492 7 жыл бұрын

Fantastic video can i do that on a alloy boat hull that has a few small holes, and what are the rods called you use, what sort of gas is it you use. Thanks farmer

@electronicsNmore 7 жыл бұрын

You can repair an aluminum boat hull, but you'll need A LOT of heat to get the job done. Use a MAPP gas torch at very close distance, or an oxy-acetylene torch. If you don't care about looks, you can also take another small plate along with 3M 5200 sealant and rivet it over the area of holes.

@Farmer2492 7 жыл бұрын

Thank you

@bishopgalane8060 6 жыл бұрын

thanks man

@electronicsNmore 6 жыл бұрын

You're welcome! Be sure to check out my extensive video playlists for other great videos of interest to you and share. Thanks

@husseinalnasrawi3766 7 жыл бұрын

what kind of flame do you use

@mightynomak4205 5 ай бұрын

whats the difference with usual soldering ?

@tousshong9438 8 жыл бұрын

Can this brazing work on repairing a crack on an aluminum oil pan? i recently bought a car and that owner was using JB weld etc.. trying to repair the crack but it still leaks and load be hold I didn't know so now I'm stuck with the car. Replacing it would be too much so was looking to repair. Thanks!

@electronicsNmore 8 жыл бұрын

Hi. Your question was already answered at my other video.

@tayandylor4421 8 жыл бұрын

if its for a car engine for what its worth just buy a new sump. the last thing you want is a repair failing and then engine seizure that could cost 100's maybe 1000's thats if its not your own life as you dont know when the engine is going to seize. believe me i done it myself at 100mph. and ground to a halt when i was on a race track, i just know what to listen out for. if you don't know what your doing. leave it to a qualified mechanic. i myself am a HGV mechanic and its not acceptable to be repairing sumps to engines you can ask any GENUINE mechanic the same question and get the same answer.. regardless if its a crack or a hole. its scrap just bin it and buy a new one.

@tennesseesam7697 7 жыл бұрын

dude if you already have the oil pan out take it to a pro done #makes a great cooking pot#take your time#sick of getting screwed

@EggicTheCreator 7 жыл бұрын

if the guy doesn't have $300 bucks for a new oil pan don't you think he wouldn't have $300 bucks to take it to a pro? and if he did don't you think he would just buy a new one?? common guys you have brain for a reason.

@jlkbbk2003 6 жыл бұрын

"Low and behold" is the correct term :-)

@craigstock7471 8 жыл бұрын

What would be the superior gas to use for aluminum? I was thinking mapp gas, not so hot.

@tellmesomething2go 8 жыл бұрын

+Craig Stock MAP GAS IS HOTTER. WATCH THE VID. DUMBKOFFS. HOW DID WE GO FROM ALUMINUM WELDING TO EU?

@teeroosam6781 3 жыл бұрын

Can you do the same with steel pots? Thanks for your reply

@electronicsNmore 3 жыл бұрын

Steel would have to be repaired using a bronze rod. You can see them in my other video below. Thanks for watching! kzfaq.info/get/bejne/nquoa5x_mMydpWg.html

@LadySadWaters 8 жыл бұрын

Does that work with cooking pots as well? I've some cooking pots I'd like to repair myself but I'm not sure if the patch would hold when using the pot again. Please advice. Thank you very much.

@electronicsNmore 8 жыл бұрын

+Linda Alexander Hi Linda. As long as something is in the pot(water/oil/food/etc), then the repair will not melt out. Leaving an empty pot over a gas flame will melt the repair area once very high temperatures have been reached. Thanks For Watching!

@LadySadWaters 8 жыл бұрын

+electronicsNmore My pleasure. The hole on my pots were luckily on the side not the base, and not as big as the one you fixed in the vid, about a toothpick hole size. I'd like to give this a try but I fear I might be doing more damage to a good pot than repairing it. Thank you for your valuable advice.

@elizabethreed9926 7 жыл бұрын

If your pot has a hole in it, I wouldn't consider it a good pot.

@alexemmanuel714 7 жыл бұрын

gud work...

@crispychicken2743 5 жыл бұрын

Great video . We may need this in a grid down situation. Where can we get the rods

@electronicsNmore 5 жыл бұрын

Hi Michael. Glad you enjoyed the video! There's a link posted in the video description area. I have a lot of excellent videos on my channel that cover many different subjects, so be sure to check out my extensive video playlists for other videos of interest to you, rate thumbs up, and share my channel with others. Thank You

@crispychicken2743 5 жыл бұрын

@@electronicsNmore thank you . Happy holidays

@eddyjr1947 10 ай бұрын

Will the same technique work for screw holes in a vertical sheet of aluminum? And, if so, can the resulting filled hole be filed or smoothed before painting?

@William_Van_Landingham_III 8 ай бұрын

Did you get it to work? This is the same project I am considering.

@eddyjr1947 8 ай бұрын

@@William_Van_Landingham_III Sadly, haven't had a chance to try it yet --life got in the way. Hopefully soon but - - - -

@hogan8999 7 жыл бұрын

thanks

@electronicsNmore 7 жыл бұрын

You're welcome! Be sure to check out my video playlists, rate thumbs up, and share my channel with others. Thanks

@hanzbe420 6 жыл бұрын

Will this work on a oil pan?

@robertsalser848 7 жыл бұрын

Thanks for the video, I've had some of these rods for twenty years, I was never able to get them to work, I think your video should help, I will probably have to use steel wool on the rods as well, they have kinda turned dark over the years. Do you think it will work on cast Aluminum as well, that's what I really need to repair.

@electronicsNmore 7 жыл бұрын

Robert Salser Cast aluminum should'nt be a problem.

@hvacae6904 4 жыл бұрын

Is it possible to braze aluminum without flux and what type of brazing rod that have used thanks...

@electronicsNmore 4 жыл бұрын

Yes, I guess you didn't watch the video.

@BenjaminShi Жыл бұрын

What is the specifications for the Heat Gun or Touch, what is the Wattage, what is the minimum and maximum temperature ranges, what it the model number and manufacturer, and where to buy the touch? Thank you

@adam_-adam 4 жыл бұрын

This looks awsome but my main question is, is it as strong as aluminum and also why does this rod melt so easy because i thought it was hard melting al with a reg torch

@electronicsNmore 4 жыл бұрын

You can melt aluminum with ease using a torch.

@fuddyduddy 7 жыл бұрын

I have a question, would heat melt the repair material again during cooking something?

@electronicsNmore 7 жыл бұрын

Hello. As long as there is food or water in the pot, not possible.

@deodiaus 8 жыл бұрын

I have several cracks in my crankcase. I am going to attempt to weld it together with a propane torch. Should I apply aluminum from the inside or outside?

@electronicsNmore 8 жыл бұрын

You need to drill the ends of each crack using a small drill bit. Doing that prevents the crack from extending further. Also grind a small depression over the entire length of the crack. The repair works great when done PROPERLY. Practice using something similar first.

@deodiaus 8 жыл бұрын

goo.gl/photos/fxcVSHajYstmigqk9 see yellow lines.

@robinrwilsonsauls 9 жыл бұрын

I have really wanted to start learning all that I can do with Brazing. I have a question concerning if you could use a square of aluminum and Braze it to another piece of Aluminum, (as if it gluing a patch)?

@jordanrowan2537 2 жыл бұрын

I’ve been trying to fix a diesel tank off a Mack Truck and it’s been a pain trying to get it to take to the tank don’t worry the fuel tank has been empty for quite some time sitting in a field

@jeromejuanis6146 4 жыл бұрын

Hi bro..just want to know, what types of gas you use?

@electronicsNmore 4 жыл бұрын

Propane is fine for small areas(thinner aluminum), and for thicker aluminum use MAPP gas. Thanks for watching! Be sure to share the link to this video with others.

@user-gv1uz7de8w 2 жыл бұрын

good 🌴🌧️

@electronicsNmore 2 жыл бұрын

Thank you! Cheers!

@hussainsabah1576 5 жыл бұрын

مبدع

@electronicsNmore 5 жыл бұрын

أنا مسرورة لأنك تتمتع الفيديو! تأكد من التحقق من قوائم التشغيل الخاصة بي الفيديو واسعة النطاق لأشرطة فيديو أخرى كبيرة من أهمية بالنسبة لك ومعدل ممتاز تصل حصة قناة بلادي مع الآخرين. شكرا

@Samson-EC 3 жыл бұрын

I have aluminum ports on my truck's throttle body and one of the ports has holes from passing 34 years of antifreeze. I want to fill in the holes but I am afraid that heating the port up will melt it. Any thoughts on this scenario? Appreciate any input..thks...hc

@electronicsNmore 3 жыл бұрын

Visit a salvage yard and swap it out, or use a 2 part aluminum repair epoxy. Thanks for watching!

@Samson-EC 3 жыл бұрын

@@electronicsNmore Well I made a foopa. I did a magnet test and found that my throttle body is aluminum but my ports are stainless steel. So I have to look at stainless steel solder..Thks..hc

@bestherc1951 5 жыл бұрын

Can I use this method to repair a gash in an aluminum garage door?

@electronicsNmore 5 жыл бұрын

Yes

@theoldshooter9011 4 жыл бұрын

Will this work on a pontoon boat toons without damaging them???

@electronicsNmore 4 жыл бұрын

Yes, but you'll need a lot of heat, and VERY clean metal.

@prashanth2776 2 жыл бұрын

This process can be used for aluminium alloy???

@electronicsNmore 2 жыл бұрын

Yes

@arifiqbal5172 7 жыл бұрын

good very good

@electronicsNmore 7 жыл бұрын

Thank You

@mamakho464 3 жыл бұрын

Great 😘 ❤️ ❤️

@electronicsNmore 3 жыл бұрын

Thanks for watching!

@hernanddiaz207 3 жыл бұрын

Genial

@GalaXy808 10 жыл бұрын

Is it gonna work for steel or any any other type of cooper or metal? Hey good job! Sir

@electronicsNmore 10 жыл бұрын

Alumite rods can be used for Aluminum alloys, Zinc Diecast, Pot Metal, and White Metal. To braze steel, you would normally use a flux coated bronze brazing rod. Thanks For Watching. Be sure to share.

@Sam-qi4hm 9 жыл бұрын

electronicsNmore Great video do you have a video on repairing pot metal?

@electronicsNmore 9 жыл бұрын

Same procedure.

@GalaXy808 10 жыл бұрын

What type if material did you used?

@electronicsNmore 10 жыл бұрын

Alumite

@statingthe_obvious6309 9 жыл бұрын

electronicsNmore hey, Al, you might wanna try alumaybe instead of alumite.

@churchmouse2540 7 жыл бұрын

Great video. I noticed you didnt prep with any flux to decontaminate. Is that unnecessary? Flux also opens the pores of aluminum to take the rod better. Thanks for posting

@electronicsNmore 7 жыл бұрын

The manufacturer said no flux is required. Thanks

@Columbariusify 4 ай бұрын

Home used propane torch is enough for it?

@electronicsNmore 4 ай бұрын

Yes

@vanessabryant8125 6 жыл бұрын

I have a small hole in oil pan on my Mitsubishi cant find a oil pan can i use flex seal tape on it?

@electronicsNmore 6 жыл бұрын

Vanessa Bryant Flex seal tape is no good for applications 200 Deg F or higher.

@vanessabryant8125 6 жыл бұрын

Is the flex seal puddy or spray better

@brettwise2995 8 жыл бұрын

nice touch aluminum melting point is 1350 F

@gajendrabaliarsingh7638 5 жыл бұрын

Where the Aluminum brazing rod is available ?? Actually the tutorial is very good and worthy.

@gajendrabaliarsingh7638 5 жыл бұрын

Is the Aluminum Brazing Rod is of only aluminium or an alloy of other metals ?

@electronicsNmore 5 жыл бұрын

amzn.to/2N9NT44 Thanks for watching!

@PIPSGuy 3 жыл бұрын

Does it safe to fix cook ware hole? I mean for meal cooking after that. Any chemical toxic. Thks

@electronicsNmore 3 жыл бұрын

Not toxic. Just an alloy of common metals.

@PIPSGuy 3 жыл бұрын

@@electronicsNmore thks mate. will try then

@P3mpi 7 жыл бұрын

What rod did you use. Nice vid man.

@electronicsNmore 7 жыл бұрын

Alumite brand

@josephjoseph5514 8 жыл бұрын

Hye can I do the same for an engine Under mount on a lawn mower ?

@electronicsNmore 8 жыл бұрын

Should work fine for that.

@miormohdshahril938 7 жыл бұрын

thanks

@baskaranmarkandulingarasa8631 2 жыл бұрын

What type of rod you used? Led or aluminium?

@electronicsNmore 2 жыл бұрын

There's a link in the video description area. Thanks for watching!

@baldevbhaimakwana2124 5 жыл бұрын

Jis se Apne welding Kiya uska name kya he

@yayansmartfren2835 3 жыл бұрын

What kind of wire do you used ? Silver wire or alumunium wire ?

@electronicsNmore 3 жыл бұрын

Links to products are in the video description area. Thanks for watching!

@Samson-EC 3 жыл бұрын

So why did it not fall through?...thks jc

@electronicsNmore 3 жыл бұрын

It melts, but still retains it's rigidity to a degree.

@Samson-EC 3 жыл бұрын

@@electronicsNmore That's pretty amazing..thks..jc

@1966cambo 4 жыл бұрын

Some advice, dont use a drill or grinder wire wheel to clean oxidation, use a clean stainless steel brush only. Scrub until you feel the brush kind of digging in, thats the clean aluminum.now you are ready to weld or braze....