Thank you for explaining without talking about your childhood

thank you for the short video. too many videos on this platform having 8 min long intros and 2 min long solutions. my nozzle wasn't even clogged, i simply watched because it was concise and i learned something.

Thanks for explaining that. It was still plugged after doing both these procedures, so I heated up a guitar string (0.011") and shoved it in the end of the nozzle and that was enough to remove the blockage.

Best video by far! Easily unclogged without any disassembly - THANK YOU!

Excellent !!! Perfect, short, sweet, to the point, and packed with information! Thank you.

To the point. No wasting time. Everything I needed to know about clogs in a few minutes

Wow - that hex key trick was like magic!! I spent 30 minutes trying to get a clog out and no progress - then heated the hex key, let it cool then pulled the filament out easily. Thank you so much!!

I should have come to you first. Everyone was saying take apart the AMS, look at the Filament sensor, do a hot extrude but they never mentioned putting the filament directly in the without the AMS to clear it. It worked. Jesus you saved me I wasted a week damaging the plastic trying to pry everything else apart. Props to you.

Been printing with my X1C for nearly a year now - just got my first clog. This video is perfect.

Just cleared my 1st nozzle clog with this vid. It was so easy Brilliant!

That guide works like a charm.Not only how to tinker those printers but it includes great solutions. Amazing

Good. No wasted blah blah blah. Information with visuals. Well done.

I should be getting my X1-Carbon tomorrow and is new to 3D printing. Saw this video and loved how straight to the point this was. As I am someone who likes to be knowledgeable about issues like these, I am very grateful for this. Thank you!

For the last example, I use my old guitar strings to pull cold clogs. I take the 5 or 6th top guitar string and heat it up with a lighter until red hot, then push it on the stuck filament. Wait a few minutes until it cools and then pull the clog out. WORKS LIKE MAGIC !!!

Just had a clogged nozzle on my bambu a1 and tried literally the first step you talked about and it worked! Thank you!

This worked! As a last step I’d recommend going through the nozzle with a cleaning tip, so the extra gunk gets pushed out

After watching so many videos, your video was the only one that helped and it was simply because you got straight to the point and also had us heating the extruder to 260, and also told us its ok to pull a little! Thank youuuu!

Thank you, I spent hours trying to fix a clogged nozzle and managed to fix it in minutes using your last tip. I have subscribed.

Solved my problem at my X1C with 2weeks only. Great Video!

unscrewed the nozzle, heated up that little hex thang with a torch, shoved it right through and now we're back in business!!! Thank you infinitely!!!! THANK YOUUUUU SO MUCH!

This work!!!! I was so nervous about unplugging and taking the whole extruder out. You made my day. And thank you for sharing this!

Great video! All new Bambulab printer owners should watch this! Looking forward to other instructional videos on the bambulab printers!

Thank you for this video! I got clogged last night and had to figure out what to do. I ended up removing my nozzle and using my hot air rework station to heat the nozzle and push the old filament out. This is a LOT easier.

Thank you so much for these short tutorials. I did all 3! It all worked. I also used cleaning filament.

Another excellent video. Literally what I was looking in my time of need of my first real serious jam with my Bambu printer. Thanks for the guidance 👍

I just had the broken filament issue but this video helped me clear it up super quick. Thanks for the info!

actually one of the most to-the-point and useful video. Thanks Kramer

Very nice, detailed, and to the point.

Thank you so much for step 3, I had no idea how to get the nozzle unclogged and this was so simple!

Thanks. I had a broken piece of filament in the nozzle and your trick worked like a charm.

Thanks. Not got a clog so far but this is great. The use of the tool to remove the clog is a new one. Cheers

You can tell your experience by the way you explained everything, thank you so much

Thx Kramer I’m awaiting delivery of my new Bambu X1C and I saved this video for when it happens

Thank you very much indeed. Your video saved my life :) I had broken filament problem . I unclogged my nozzle with your heated allen key method. Thanks again

Thank you so much!!!! Got my stuck broken filament out easily with the help of your video!! So much appreciated! ❤

Perfect video! Heating up the allen key and shoving it into the hot end is a great idea. Going to give that a shot now.

Awesome video. Straightforward and well explained. Helped me clear a clog faster than ever. Thanks!

#3 was what I was looking for. Thanks for the solution.

Thank you, cleared my first ever blockage with your last method. Had to do it 3 or 4 times but it worked.

Awesome! The cold pull fixed my issue that I'd been struggling with for a week. Thank you!!

Kramer, you did the job!

Great video, the third method worked very good at my first try

Oh my god thank you so much!!!! Cold pull was the answer and it worked first try!! I was without my printer for 3 weeks!!

The last solution is straightforward and effective. Will try to do

Thank you - saved my ass with your tips. I ended up heating a 1.5mm hex key, pushing it into the hotend from above slightly, then letting it cool down and "set." This allowed me to pull the clog out from the top. Life saver!

Thank you for explaining it very clearly. I thought I had done almost everything there was to do concerning fixing problems on the Bambu x1. Boy, I was definitely wrong.!! This helped thank you very much!

Thanks, a neat method to removing a broken bit of filament that worked perfectly. I would recommend using something other than a hex key, it ruins the temper on the tool. I used the back end of a small drill bit held with a craft knife handle.

These are great lessons. Should be on the Bambu knowledge documents

I just ordered an X1 yesterday. Looking forward to getting it and taking my 3D printing to the next level. I've been using Creality Ender printers for 3 years. I'll will keep my 3S1 and use it as a secondary machine. Just subscribed to your channel.

Thank you! This also works for P1S, of course if anyone is wondering.

Thank you kindly, whats better is bambu delivers very nice and long allen key that is perfect for the job!

Exellentte vidéo , j''avais fais la technique de la clé à l'aine chauffée mais ça à rebouché encore après . En faisant la technique du nettoyage à 100° j'ai vu mon filament noir ressortir avec des impurté blanche ... Cette vidéo m'a bien aidée .

Thank you! Man this saved my butt. It was the first time i had a clog at the nozzel.

The broken filament tip is awesome.

thanks, you gave me the answer and fix i needed in the first 50 seconds.

Thank you for covering the technique of removing filament that has broken off flush at the inlet of the print head, I've been unable to clear mine and will give this a try.

Thank you for making this. Got my first clog after 1 month and this helped greatly! THANNKKK YOOUU

Thank you very much this did the trick.

Oh man. This will certainly cut down the swearing.......just kidding. Excellent video, very straight-forward and the information is priceless.

Well explained, thank you! The conciseness of the presented solutions is especially appreciated when you need such knowledge ASAP. :)

I cannot thank you enought to show us that trick, i spent like an hour trying to figure out, how tf i would unclog this if the needle doesnot nothing, simple and smart trick, i hate myself for not thinkgina bout that. Thankts!

Thank you so much. I had a problem that filament stuck in nozzle and your advice helped me to release it back

That was clean and concise - well done - learned 3 things today. Thank you.

Thanks. Helped me understand the cold pull ❤

Outstanding, good information without and banter and jabbering. Well done indeed thank you.

Thank you so much, you saved me a lot of money and pain and I love you thank you so much

As always - excellent video! You're the best help on KZfaq for Bambu Lab printers and more! Thank you.

This fixed my issue with my Bambu. Thank you!

Thank you! The last method worked incredibly well.

Subbed for not learning about your philosophical views and just getting the info I need.

Excellent advice and demonstrations. Well done and thank you! 👍

Thanks very much. Your procedure for unblocking hot end was great. Easy to follow🖐😀

Number 3 worked for me. Thank you.

Short sweet and worked great.

Great, helpful, clear, short video ! Many thanks. Could you do a video on disassembling the P1S extruder assuming the fixes in this video don't work ?

The cold pull trick helped me. Thanks

Best overview on this I've seen. Great job and thanks!

Ausgezeichnetes Video. Sehr hilfreich. Danke.

Glad that I know these tips now

Works perfect, thank you from germany😊

The allen key method was the fix for me :) Thank you so much!

don't ya just love finding something on the top of your google list that just bloody works, simple, easy, back up n running, uping cooling on ASA print profile,..... Cheers chap, awesomeness indeedly😁😀

My god I wish I’d found this before following another KZfaq clip where the first thing they suggest was dismantle the hotend… it took me four hours of pain to get the printer working again afterwards when it didn’t recognise the hot end fan. If I’d watched your video first I would have avoided potentially destroying my new printer 😮

EXCELLENT video. EXACTLY what I needed. Thank you 🙏

Thanks for the tips, this seems to have solved my recent printing issues😁

nice, a video too. with many thanks and greetings from Germany

Thanks for the help! And youre very straightforward and easy to understand. Following for more for sure :)

Saved me so much fuss, thank you!

This worked perfect, thank you!

Thank u short and sweet and everything worked.

Very helpful, well explained and properly shown.

thank you. I didn't have to take apart the extruder for this.

Nice trick with the broken filament cleanout.

thank you, you just got a new subscriber!

Very good video. Thanks a lot!

That helped so much! Really good job

This was great, very straightforward and to the point. I hadn’t previously known the proper procedure for a cold pull, many thanks! I also had never seen the trick with the hex key, to pull out broken filament, *BRAVO* for that! (A ball-end hex key would be especially good for this, as the ball would give the filament a lot to grab onto :-) A note though: It would depend on the alloy the hex hey is made from, but heating it might result in a change to its hardness or toughness. - So probably only do this with a key hey you don’t care about using in high-torque applications.

Great video! You got me up and running quickly!

This was very helpful thank you

Super simple explanation. Thank you very much