I also used the Stormsure Flexable Repair Glue on some small holes that I had, but while the pump was on deflating the spa, I put a blob of the glue on the hole and some got sucked into the hole and before too much went into the hole (dependant on the size of the hole), I switched off the pump and let the air back in to the spa to have equilibrium (same pressure inside and out). On tiny (cat claw pin pricks), I did not even need a patch over it. I have recently had some holes appear along the seam between the blue outer and white inner and used Lay-Z-Spa BWA0010 Vinyl Repair Kit (glue and patches) and found this to be utter S**T. The patches did not stick properly if you did it the way the instructions tell you, so then put glue on the tub as well and it worked well for over a day until the glue gave way. Now I have a hot tub at 36 degrees full of water and deflating overnight.....Great. Going to try Stormsure and patches after keep pumping the tub up to use it a few times before draining and repair.

Always handy when you know exactly where the hole is 🙈

Why do people insist on putting rubbish music over these videos rather than telling us what they are doing and what products they are using!

What glue is this? No info available online and never included with patches.

Use coleman campers fuel to clean surface and a vinyl patch Use rubber cement glue apply thin even coat on both sides Apply even pressure or use a roller

Stormsure Flex repair adhesive worked for me. Lay-Z-Spa clear patches are joke like others have commented.

It would be helpful if there was a voiceover to explain things to make it clearer. Maybe answer some of the comments here in the process. For example is the air pump on to create the soapy bubble? Does the tub need to be drained or can it be done whilst still holding water?

I had several holes in lazy spa tried everything lay spa patches, silicone, lazy spa glue, spent loads trying to get repaired with these got done now only one that works after much research is STORMSURE cannot fault this at all follow instructions plugs all holes

Two nice easy repairs. What about seams or in the recess show those

Those clear patches are jokes. The sticky substance literally melts when the sun heats them up. Go to your local dollar tree or where ever and get some fix-all adhesive. Pour a glob onto the hole and let dry for one hour. Cut a piece about 3 times larger than the hole out of the included vinyl material that comes with your hot tub and squirt a fair amount onto said patch. Let it tack up for about 10 minutes before sticking it onto the actual hot tub. Wait until the next day before filling with air and water. This also works for seams but only for small repairs.

I was told this is PVC, a guy on KZfaq used medium grey pvc cement and it worked. I'm about to try it

Those clear patches work temporarily. I'm on my third in the same spot. Always unsticks and an air tunnel is created over the hole letting air out again. I'm guessing the hot Australian temperatures loosens the adhesive of the patch?

Two different repairs, which one is best for the bottom/underneath?.

The worst thing you can buy is this “jacuzzi “ it’s a nightmare it will always leak from somewhere cheap plastic ventilation tube inside that will break in a matter of time

Any one know of how to repair a split seam on the jets bought mine 6 months ago, only used it 3 times and useless after

Would be useful for you to tell everyone where you can buy the repair kit from??

I have a hole on the inside of the airbubble tube with the holes. I will have to cut the tube oben to access the hole. Not shure if I will be able to repair the cut I have to make...

Common sense isn't so common Tub must be empty NO water Leave inflator ON Check using spray bottle with soapy water or sponge Methodically work in small areas Mark area with a tack Remove tack Sand area ( scuff ) to promote rough area for patch Drop super glue on hole Let dry Add super glue to effected area Add patch Use credit card from center out flatting & push super glue out to edges Let cure 10-15 minutes Move on to next leak Repeat Only work on 1 at a time Must allow 1 repair at a time to cure This video was ok lack of tutoring was lame music was horrendous

I used these on my lay z spa cover the inflatable part absolutely rubbish do not work and just peel off

Can I use the same clear patch for the bottom part? Wee have a puncture at the bottom seam so I'm hoping that will work. 😢

Where do you get those sticky patches???

Mine didnt come with glue.. Are you joking? It had a pinhole from shipping I only realized after it was all filled and setup ready to use. Garbage product.

I have a slice due to dog..can I use neoprene wader repair?

Someone commented on this video using my name and I apologize for the rude comment and removed it.

can i ask what repair kit u use to fix this as in have misplaces mine. i have punture on the black part of spa i have patch on it but air keeps gettin out it

hands thiccc

How do you find the hole if it’s not leaking water but just air?

Those patches are a JOKE!

I’m 100th like!!

tec7 does the job better

Patches are shite

What a terrible video providing no help whatsoever

Why on earth do you have to play this stupid bloody music. Could you not have a detailed written explanation on each task for this repair or actually someone explaining this. This is purely to cover costs and saves on individual European languages. Pathetic really.