the back plate template is pure genius it is definitely something I am going to make and use moving forward!
@briggsmalcolm11023 жыл бұрын
a trick : you can watch series at Flixzone. Me and my gf have been using it for watching all kinds of movies recently.
@zaynfrancis35073 жыл бұрын
@Briggs Malcolm yea, have been watching on Flixzone} for since december myself :)
@pierrecosta37893 жыл бұрын
Thank you Pablo , I am new to guitar building but every time I watch one of your videos I am learning something from its a pleasure to watch , keep up the great work.
@redkitekk3 жыл бұрын
Thank you. I am really pleased you find my videos helpful. Just in case you are interested I have a complete course available on www.onlineguitarmakingcourse.com
@alkssmith2 жыл бұрын
Bravo, maestro, another great video!
@backspatter7 жыл бұрын
Thank you Pablo-the back template is a great idea
@redkitekk7 жыл бұрын
Thank, I am pleased you like it!
@thebault10006 жыл бұрын
backspa
@simondupreelagak24453 жыл бұрын
Thank you and I appreciate this so much.
@redkitekk3 жыл бұрын
You are welcome, You might be interested in this course I have recently done, you can find it on www.onlineguitarmakingcourse.com
@edwinaponte97 жыл бұрын
Very good video, thank you.
@18roselover7 жыл бұрын
hola Pablo , ,Where did you purchase the wide mini c clamp. /? I have not seen anything like it here in the usa I use small spring loaded clamps thank you
@redkitekk7 жыл бұрын
I found them on eBay some time ago... I think this is the newer version of them. www.ebay.co.uk/itm/S-PCL1003-Modelcraft-G-Clamps-Magnet-x-3-/112359838237?epid=1838038383&hash=item1a292b121d:g:27UAAOSwTM5Y5M3C
@18roselover7 жыл бұрын
thanks pablo
@gillesclouzeau58017 жыл бұрын
Hello pablo, I always watch your videos with interest and I have a question: I read that you use a radius of 20 ft for the back, for all your models? And yet another question, how do you build your dish? Thank you for your videos. Gilles
@redkitekk7 жыл бұрын
Hi Gilles, I actually use a 25 ft radius dish. It isn't difficult to make your own dish, it is just time consuming and dusty....very dusty, so if you find where to buy them it is worth it. If you want yo make your own dish there is already a video from A lady that explains very well how it is done. I made mine using a very similar method as in her video kzfaq.info/get/bejne/aKx3obynndupmZ8.html I hope you find it helpful. Best wishes Pablo
@gillesclouzeau58017 жыл бұрын
Thank you very much Pablo
@TS1835D6 жыл бұрын
PabloRequena t
@3DMVis3 ай бұрын
Hi Pablo, thanks for your great videos. You start this video with the linings already in place. However, the sides need to be already tapered to the right body size. How do you taper the sides? Did you mark the final taper sizes on a straight line and cut them before bending? How do you make sure that you end up with the right body size at the tail and heel since it's hard to bend at an exact location. Do you measure again the depths after the sides are in the solera?
@redkitekk3 ай бұрын
Hi Juan. I have a template that I use to trace the shape into the sides and cut them to shape before I bend them. It isn’t a straight line as the back isn’t flat the sides need to be shaped to accommodate the arch of the back. On my course available on line I explain in detail how to do this and I provide plans with this template and other templates used in the course. You can find it on www.onlineguitarmakingcourse.com
@3DMVis3 ай бұрын
@@redkitekk Thanks, I'm working with Nicholas so I'll pass the message.
@manconello6 жыл бұрын
Thank you for your video, Mr. Requena. I can't see the bridge plate in your videos. Is it because you don't use the bridge plate? Am I missing something? Thank you. Antonello
@redkitekk6 жыл бұрын
Hi Antonello, In this case I didn't use a bridge plate, sometimes I do, each guitar is different.
@okiwatashi7 жыл бұрын
Thanks for the videos Sr Requena, can I detect a wee bit of Scottish in your accent?
@harryodum55984 жыл бұрын
I would love to take your class Pablo. Do you have them on a regular basis?
@redkitekk4 жыл бұрын
Harry Odum yes, I do, if you want info about it have a look at www.guitarmakingcourse.org Here you will find dates, prices and all the info you need about it.
@sat59027 жыл бұрын
Thanks for the great video. What is the radius that you use in your sanding board?
@redkitekk7 жыл бұрын
I use a 25 ft radius dish.
@thibaultjaberg46587 жыл бұрын
Hi, did you make the radius dish yourself? Or is it easier to buy one.
@redkitekk7 жыл бұрын
I made my own, but it surely is easier to buy them already made as it is a lot of work. Have a look at this link, they sell 20 ft and 40ft dishes, see it they work for you.I use 25ft radius dishes www.dictum.com/en/musical-instrument-making/special-tools-for-musical-instruments/guitar-tools/703937/radius-dish-guitar-40-ft