HOW TO FIX BATTERY FAULT IN FIRE ALARM PANEL ?

Рет қаралды 19,882

FIRE PROTECTION GUY

2 жыл бұрын

I attended a service call due to a battery low (voltage) fault. What is the reason and solution to fix the problem?

Пікірлер: 29

@niloyu105 2 жыл бұрын

Watching from Al Khafji Saudi Arabia

@simonegelormino3277 2 жыл бұрын

Nice work Elmer! I rwally enjoy your videos!Waiting for a video on fault finding for common faults found on Ewis panels, wip phones, break glass, speaker line etc😉

@niloyu105 2 жыл бұрын

😂😂😂 masipag Ngayon ang Ads start and end video 20sec. Completed support Filipino Vlogger especially Ads 😂😂😂

@o_z_b 11 ай бұрын

Thank you so much for this video

@maskarangvlogger7196 Жыл бұрын

Bago nyo pong taga suporta sir.

@niloyu105 2 жыл бұрын

Welcome back hehe! Watching from Al Khafji Saudi Arabia

@fireprotectionguy7943 2 жыл бұрын

My PC Motherboard was off. Under warranty, so I sent it back to the supplier. I can not wait for the repair so I bought another PC. Thnxs Ingat.

@niloyu105 2 жыл бұрын

Ah! Naka panood din ako Ads 😂😂😂 30sec. Ads completed keep watching and support from Al Khafji Saudi Arabia...

@fireprotectionguy7943 2 жыл бұрын

Daya...pinagkakakitaan na nila ang video ko.

@niloyu105 2 жыл бұрын

@@fireprotectionguy7943 Hehehe! Oks lang yun Sir Elmer alam ko naman po naglilibang ka nalang sa buhay 😂😂😂

@fireprotectionguy7943 2 жыл бұрын

@@niloyu105 ... tama ka dyan...dadagdag lang sa tax na babayaran ko yan.

@workonmyranger6336 Жыл бұрын

I like your videos

@fireprotectionguy7943 Жыл бұрын

Thank you.

@ericchoi1610 8 ай бұрын

thank you for the video. How did you find a magnet door was the problem? is it common failure or based on your experience? if you didn't know, how would you troubleshoot in general?

@fireprotectionguy7943 8 ай бұрын

Fire system auto battery test once a day (old system) or once a week (new model). For old system, it's an hour test. Any magnet or external power devices cause the battery to depleted earlier. In this site, it's only the magnet that causing it. From the day I introduced a new power source for the magnet, the problem never re-occur.

@roderickbalolong6795 3 ай бұрын

Hi Sir. Elmer, maybe during the design stage the magnetic lock current was not included in the battery calculation.

@fireprotectionguy7943 2 ай бұрын

True. But magnets must not be included in the normal power supply of the fire system. It should have it's separate power supply. Either with back-up batteries or not.

@carlh4279 2 жыл бұрын

For sure the magnets should have a dedicated power supply.

@maskarangvlogger7196 Жыл бұрын

Bagong palit din po ang battery naun eh..slamat po advance

@stevehunter532 Жыл бұрын

Does the system need to be shut down to replace the batteries? Or can be done while running on mains power?

@fireprotectionguy7943 Жыл бұрын

No need to shutdown. Power should always be ON.

@francisaguinaldo968 11 ай бұрын

Hi! How to fix psu fault in zeta primier quatro? Thanks

@fireprotectionguy7943 11 ай бұрын

I am not familiar with zeta. But the trick is all fire supply fault are the same - Battery Missing, Battery Fault, Blown Fuse, Battey Flat ( just replace it!), Low Battery Voltage, No Power Output or Input, Output voltage is too low ( Normally output is between 26.1 - 27.4 volts DC). Good Luck

@crisdeorbz8986 Жыл бұрын

Good day sir may video po ba kayo procedure replace battery ng consilium fire alarm panel?

@fireprotectionguy7943 Жыл бұрын

Replacing batteries are very basic. When replacing, make sure you have your normal power "ON". Once you removed one terminal, it will fault buzz and just acknowledge it to clear the noise. Just do make sure you got the correct polarity.

@crisdeorbz8986 Жыл бұрын

@@fireprotectionguy7943 ok sir no need to switch off the main power, only disconnect the battery wire

@fireprotectionguy7943 Жыл бұрын

@@crisdeorbz8986 ..correct. Never remove a battery with MAIN POWER OFF cause your battery is the back-up power source.

@maskarangvlogger7196 Жыл бұрын

Sir,itanong ko Lang po Kung ano dahilan nang battery deplited?simplex po addressable

@fireprotectionguy7943 Жыл бұрын

Flat batteries. Mostly cause of system that is running on batteries most of the time due to power blackout. Once a battery reached it's low voltage threshold - it's hard to charge using the fire alarm system battery charger. Best to charge it using an external charger. Another is, the system is in auto battery test every day. Once a week is okay for 30 mins only based on program setting. If it failed in 30 mins, your system requirement is bigger than the battery can supply. That's the time you sort out which equipment should not be included in the normal battery test and should be separated from the fire system. These are magnet door holders mostly.