How to Fix Oreck XL Fan
Рет қаралды 24,174
5 жыл бұрынPretty simple and cheap to do.
Brush Roll and Belts
amzn.to/2Xhds7v
Replacement Outer Bag Assembly
amzn.to/2TYtjpD
Hepa CC Bags (What I recommend)
amzn.to/2XjRMHW
Fan
amzn.to/3eF02rZ
Fan Housing
amzn.to/3dmaG6u
Cord
amzn.to/2zDKGFl
Commercial 3 Prong Cord
amzn.to/36XZvih
Light Bulbs (standard)
amzn.to/2XPoY94
Link for LED Bulbs
amzn.to/2ZqkLLA
FELT PIVOT WASHER
amzn.to/3XOU0Mn
I am a participant in the amazon affiliate program.
Disclaimer:
Due to factors beyond the control of Hank's Garage, I cannot guarantee against improper use or unauthorized modifications of this information. Hank's Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Hank's Garage recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Hank's Garage, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Hank's Garage.
@helenwood3199 Жыл бұрын
Hank, this 61 yr old lady is sending a big hug to you for your detailed, thorough video. Because of it, I gathered the courage to attempt to swap out the motor on my Oreck XL. Was nervous, but sooo satisfied when I plugged it back in and flipped the switch. Vvrrrrooom...the beater bar whizzed around. 😁💪🏆🍾
@aunabreslingaming3279 9 ай бұрын
God this is one of my favorite comments
@michaelgustow8973 Жыл бұрын
Thanks for you video instruction! Saved me a whole bunch of money on my Oreck XL21! Turns out my motor was still ok but the fan in the blower section was frozen against the housing. Also great tip on reverse threaded nut for blower fan.
@Planedoc1959 8 ай бұрын
Love restoring these old XL 1 and 2’s. A 7/16 socket also fits the fan nut.
@brianc5939 Жыл бұрын
This video helped me replace the fan kit. I had trouble removing the fan from the motor. After removing the nut it did not come off. It was stuck on after 20 years of use, but mission complete. TY
@PerformanceReviews 5 жыл бұрын
I would have had to put that whole thing in the Dishwasher ! Nice quick how too .
@hanksgarage_ 5 жыл бұрын
Yup I’ve done that before for sure
@randomvids5883 4 жыл бұрын
Hey performance reviews. I love your videos.
@goodkarna 2 жыл бұрын
Thanks! This is so helpful. I have the XL 2200 rs and trying to fix some things. I'm wondering if you know the part number of tiny front wheels on each side of the brush. I've looked everywhere and I can't find any information.
@dannyn5041 2 жыл бұрын
Hi Hank garage I got a new johnson motor for my oreck and the older model motor looks like a lamb or amtek motor don't know because it is rusty I can't seem to get the nut washer screwed in to the motor shaft keeps falling out maybe I'm tightening in the wrong direction got the motor on eBay for my 98 oreck
@amor4geo Жыл бұрын
Your video was big help! Thank you.
@Dustin-rb8mp 4 жыл бұрын
I have a oreck xl. Motor was sounding a little funny. Took the motor apart and noticed the fan blades are filed down like they have been rubbing on the intake. Also when I took it apart I didn't have to remove the nut on the fan, it just pulled apart. Should I order a new fan and intake?
@traymarr6468 2 жыл бұрын
Dear Hank's Garage, If I just want to replace the fan housing (it's cracked) can I keep all the wires connected on motor? Thank you...
@DANNYN224 2 жыл бұрын
Yes I did mines
@MrTL117 5 жыл бұрын
Simple and straight forward. Nice vid! And nice to see another Vacuum video
@stevekullen2150 4 жыл бұрын
I've followed the directions - thank you! But got stuck at the fan nut stage. I removed it as shown but the two housing parts won't come apart. Any suggestions - aside from going to Oreck AND I already bought a replacement Fan Housing for my XL121?
@hanksgarage_ 4 жыл бұрын
Takes a minute sometimes but you’ll have to “rock” it out. Maybe try some wd40 on the shaft
@bodeine454 5 жыл бұрын
I have an older Oreck XL, the wiring for the motor and switch is wired together with wire nuts instead of connectors. And I took the nut off of the fan and still can't get the fan to budge. I also can't get the bottom pipe off of the fan shroud. I guess I need to spray some penetrating oil on it or something. Not sure why the fan won't come off....
@domsstuffrippingonscooter2400 4 жыл бұрын
Howdid you get the fan off
@williamthomas8135 2 жыл бұрын
A small "pulley puller" should work
@williamthomas8135 2 жыл бұрын
which 'XL" there seem to be a dozen versions. Most not listed on the Oreck site.
@hanksgarage_ 2 жыл бұрын
They are all the same machine just a different color. The XL21 is different from the XL thats the only other model.
@stradivarius151 2 жыл бұрын
@@hanksgarage_ Any idea if the XL21 is similar to this video? I have one and need to replace the fan housing as it is cracking and leaky.
@johnpyros4993 3 жыл бұрын
Where could I find a wiring diagram for XL3600HH
@hanksgarage_ 3 жыл бұрын
They are typically in the back of the parts listing PDFs you can find on google.
@hanksgarage_ 3 жыл бұрын
www.manualslib.com/manual/800111/Oreck-Xl3600hh.html
@williamthomas8135 2 жыл бұрын
Which felt washer is supposed to go where?
@hanksgarage_ 2 жыл бұрын
against motor
@leovegas86 3 жыл бұрын
My oreck model doesn’t have regular Phillips screws on the bottom. What are these?
@hanksgarage_ 3 жыл бұрын
Torx screws probably
@leovegas86 3 жыл бұрын
Bought me some torx bits to see if they are thanks!
@Horseyhorsehorse 3 жыл бұрын
Requires a T20 Torx screwdriver, or an extra-long skinny extension for a bit.
@leovegas86 3 жыл бұрын
@@Horseyhorsehorse yeah I opened it with torx screws thanks lol
@TMech-hk9hh Жыл бұрын
Seems like they almost all are Phillips but a few are star bit or TORX.
@joshuaryanferguson3702 3 жыл бұрын
im just getting a new motor