How To Fix the blade clutch on a Honda mower

No video

How To Fix the blade clutch on a Honda mower

Рет қаралды 15,873

Жыл бұрын

Disclaimer: Repair at Your Own Risk - Consult a Professional if Unsure
This video is intended to provide helpful information for DIY repairs. However, please note that attempting these repairs carries inherent risks. By following the instructions provided in this video, you agree to take full responsibility for any potential damages or injuries that may occur.
Tool List:
Socket Wrench
Breaker Bar
9/16" Socket
Safety Glasses
Pliers Or Flathead Screwdriver
Phillips Head ScrewDriver
The most common reason for needing to replace this part is:
Blade Won't Stay engaged in tall grass
Subscribe to never miss a helpful video

Пікірлер: 32

@pjlifehacks2722 Ай бұрын

Nice Simple Video, Thankyou!!!!!!

@thehelpfulchannel5 Ай бұрын

Your welcome if you have any video suggestions feel free to leave them below

@richardhalbur4347 Жыл бұрын

The clutch spring is on wrong and that is why it is not working properly. Look it up on parts diagram and shows you the proper way. Plus that spring has marking saying up.

@thehelpfulchannel5 Жыл бұрын

Ok thank you

@iPhoneBenim61 11 ай бұрын

Sen varya gercekten süpersin 👍🏼

@thehelpfulchannel5 11 ай бұрын

Thank you please be sure to subscribe to never miss a helpful video

@robertpinder2307 11 ай бұрын

Are those "standard philips head" screws or JIS screws? You can " screw" them up with the wrong screwdriver.

@thehelpfulchannel5 11 ай бұрын

The ones that hold the cover on are standard Phillips head screws

@mgomez5606 11 ай бұрын

What honda model is yours? I have HRX217.

@thehelpfulchannel5 11 ай бұрын

HRN216VYA

@mgomez5606 11 ай бұрын

You make look easy. My belt is tight. Your has no tension. Wonder why?

@thehelpfulchannel5 11 ай бұрын

You have to remove the spring that keeps the self propel belt tight it is near the rear of the mower next to where the pulley sits in the rear

@mgomez5606 11 ай бұрын

Should of put some grease on shaft to prevent it from getting frozen on.

@thehelpfulchannel5 11 ай бұрын

Thanks for the suggestion

@mgomez5606 11 ай бұрын

@@thehelpfulchannel5 I have had some where I could not get it off.

@thehelpfulchannel5 11 ай бұрын

Ive heard of an Interesting mix of automatic transmission fluid and acetone idk if it will work better than store bought but its definitely worth a try. The mix is 50/50

@noelopez4000 2 ай бұрын

Is there a way to permanently delete it . And not have the lever up top

@thehelpfulchannel5 2 ай бұрын

What lever? The one for the blade clutch? It is a safety feature required by law on all mowers. And removing it can be a safety hazard

@noelopez4000 2 ай бұрын

@@thehelpfulchannel5 how do i remove it though

@thehelpfulchannel5 2 ай бұрын

Unfortunately i would not know

@mgomez5606 11 ай бұрын

Order a new bearing for the plate you replaced and replace it. You will have a spare plate.

@thehelpfulchannel5 11 ай бұрын

Thanks for the suggestion

@donalburns6548 9 ай бұрын

I have been trying to replace that bearing on my HRR2169VYA mower. The difficulty is removing the outer part of the original ball bearing. It seems to be push fitted and so far impossible to remove. Is there a video with suggestions about removal of the original bearing? Thanks.

@mgomez5606 9 ай бұрын

@@donalburns6548only the middle part came out and the race stayed on it?

@thehelpfulchannel5 9 ай бұрын

@donalburns6548 if i remember correctly i either used the end of the screwdriver and a hammer or a chisel and hammer to remove it. Yes it might take a bit of force

@mgomez5606 9 ай бұрын

@@donalburns6548put some oil on it and use punch to tap on it by alternating sides to tap it out. Screwdriver could score the bore. Just take your time.

@kcuster57 8 ай бұрын

You have the clutch spring UPSIDE-DOWN !!! That is why there are scrape marks on the driven disk. Better check your work.

@thehelpfulchannel5 8 ай бұрын

Thanks for the comment

@zekekunze1176 Ай бұрын

This procedure is incorrect. This will cause premature wear! Exploded parts diagrams are readily available. Print a copy or have your phone/tablet with you. Servicing the blade clutch system is fairly easy.....im not sure how this guy managed to mess it up 😂

@thehelpfulchannel5 Ай бұрын

Thanks for your input