Hi all . in this video How to topcoat/gelcoat a boat, im showing how i topcoated/gelcoated my boat .i hope this helps with any jobs you have coming up .
Пікірлер: 277
@markfennah43222 жыл бұрын
What a great well informed and enthusiastic exposition of gel coat work - absolutely brilliant, and if great help help ! Thanks so much
@westcoastprojects012 жыл бұрын
Thank you. Glad you enjoyed
@neilfixes55012 жыл бұрын
Thanks for this encouraging video. I have made a few replies to some comment questions. One point...I was taught to leave a thick stand-up edge at the end of each section and not feather it out like you would for house paint. If you have to stop work for any reason (dont answer phone calls or chat to visitors...😀), a thin feathered edge will not build up heat to cure properly and the overlap area will 'tripe' (wrinkle) when you restart. Also, prep. is king...scrounge plastic ice-cream containers whenever you see them, and always have rolls of kitchen paper towels at hand.
@timashcraft6262 Жыл бұрын
Top Tip. Use a water hose, wet the floor completely to help keep dust down as you walk around.
@Jonathanbaker2 жыл бұрын
Liked the video not like the other videos out there. Your clear and up front with no long introduction to the job. This is going to help me redcoat my own yacht. I was afraid to paint the boat with gel coat now I am more comfortable with having a go at it.
@westcoastprojects012 жыл бұрын
Good thing with this stuff . Just get it on and don't worry about how it looks . It's all about getting enough material on so you can cut and polish it . I'm glad you found the video helpful
@nixsonbronson45952 жыл бұрын
@@westcoastprojects01 Hi what grit sandpaper do you start and finish with before using a compound and then waxing? Thanks
@westcoastprojects012 жыл бұрын
@@nixsonbronson4595 check out My other video on how to cut and polish
@wildcoastadventures75352 жыл бұрын
Was thinking the same thing. 5 minutes and it's become a do-able, complete with ratios of catalyst plus drying time. 💯👌💪
@28theark5 ай бұрын
@@westcoastprojects01hello I’m going to be buying a boat this year and repainting it myself but I’m new to this 🤷🏻♂️can you recommend a quality sanding rotary tool like the one your using and a link to a good quality fibreglass boat paint company? I’ve got some acetone and hull cleaner and gel coat and all the tools but wanting a really good quality main body paint for the final job and I like jet black any help would be really appreciated and what type of grits aswell cheers
@SailingJohanna2 жыл бұрын
Thanks for the informative tutorial… well done! ♥️✌🏼⛵️
@sethook-ro4xh Жыл бұрын
Looks great. I really want to use this method to paint my two man Fishing boat.
@waterbourne92829 ай бұрын
Nice simple tutorials, thanks mate.
@perryberens6182 жыл бұрын
Good video. Kept the purpose real. "It's a fishing boat." If the fish aren't biting it's not the paint finish that stopped them. Looking forward to your next video. Hand rolling and finishing will be an interesting result to watch.
@westcoastprojects012 жыл бұрын
There is a video on the cut and polish steps
@mchabi18 Жыл бұрын
Great job and nice tips ! Thanks
@georgenettlesjr14668 ай бұрын
Great video you brought that thing back to life great pointers and tips as well😊
@westcoastprojects018 ай бұрын
Thanks mate
@gbmacc582 жыл бұрын
Very helpful, Thanks!
@thiodorchalkias89062 жыл бұрын
Nice job!!! Be Careful about the vapors of the painting bay be is toxic!!! Thanks for sharing!!!! Best Regards from Hellas (Greece)!!!!
@cassiopietsch13772 жыл бұрын
Meus parabéns pelo Vídeo me ajudou aqui no Brasil
@para13242 жыл бұрын
Beautiful and informative. Well done. 👍
@westcoastprojects012 жыл бұрын
Thank you
@wildcoastadventures75352 жыл бұрын
Cool, short & informative video. Thanks. Now I know how to Gel-coat too 💯👌👍
@adamkendari1513 Жыл бұрын
Valuable lesson ❤❤❤
@nedhawn955310 ай бұрын
Excellent tutorial
@andrewwarren42062 жыл бұрын
Cheers. I am gonna give it a go.
@tanksouth2 жыл бұрын
Saved it. Thank you.
@MilesCobbett Жыл бұрын
You might try the 3 ft long door roller handle. It makes applying paint much easier and quicker.
@JhanDeCal11 ай бұрын
"Roll and Tip" Helps to get a case of good beer and lure a buddy over. One to roll and the buddy to follow with a good brush. 👍👍👍
@hub70932 жыл бұрын
Your right about not needing a expensive brush. But you also need to be qualified to use it 😁all you had to do get it full of paint. Then wipe out, then just ah touch of paint on the end then put lines in your roller marks. Doesn't hurt to thin your dipping paint ah little bit either.
@000gjb2 жыл бұрын
I have sprayed Gelcoat mixed with Ferro brand "Patch Boost" in an Acrylic mini spray gun to blend in repairs into existing Gelcoat on boats. You have 10 minutes before cleaning the gun out with Acetone. Works a charm. If you are recoating an entire boat, an epoxy primer with a Acrylic Polyurethane top coat is the better finish. Flat and high gloss mirror finish straight out of the gun with no refinishing, that is as long as you avoid runs. Any colour you like.
@westcoastprojects012 жыл бұрын
I've just done that on my other boat . Comes out great
@southerntexashomestead50282 жыл бұрын
Yes please. We would like to see the next step. Thanks for sharing the video.
@westcoastprojects012 жыл бұрын
Check out the other vids
@nymack662 жыл бұрын
In a controlled environment like your shop, I would have done a no-wax Gel then a light spray with a finishing Gel then buff with Aqua Buff 1000-W Fast Cut Compound, followed by Aqua Buff 2000- for a mirror finished (I refuse to sand) I did this back in 2009 on my 84 Wellcraft V-20 it still looks amazing to this day. I like your work and simplicity, thanks for sharing. Hopefully, folks can see how easy it is to use Gel, most people are scared of the product.
@westcoastprojects012 жыл бұрын
The idea on this video is for people without the fancy shop and equipment. I could have easily done it so much differently.
@jaypurchase794811 ай бұрын
Got an 89 wellcraft v20 I’m bout to start finishing , wish I could see some pics
@edwardhovitz17537 ай бұрын
Dude, make a vid
@doonhamer2523 ай бұрын
Did you make a video yet?
@raymondcascella49202 жыл бұрын
The way to go is spraying, of course you need to add acetone to thin the product and a gun that will handle a heavy material like gellcoat. Knowing what I've learned over the yrs I would use an airless sprayer to get a smoother finish. You don't want to use as much catalyst as they recommend because it can kick up in the gun you also have to be a fast sprayer.get it on and guick clean the sprayer or gun.
@globyois2 жыл бұрын
Try a %100 natural bristle brush. The tips are finer than man made nylon or polyester and it will hide the brush strokes much better, leaving a more slick and “laid down” finish.
@westcoastprojects012 жыл бұрын
Cheers mate I will give that a try
@tomm9427 Жыл бұрын
What get coat brand and colour is this, It looks amazing
@jaimealfonsonoguerafuentes14532 жыл бұрын
Buenas noches amigo excelente trabajo,que clase de pintura es,te hablo de santa Marta Colombia y lo que explicas está en inglés
@paulscarlett52588 ай бұрын
Very good information What primer did you use? Also I want that gel coat where can I get it from
@niconine26811 ай бұрын
Is gelcoat just polyester resin with the pigment added. In this case blue ? Would like to know if i can use it in colours i like to coat surboards when i refurbish them. Would have to panel wipe before application ? And what about wax finnish. Can i add the wax/styren to this gel coat ?
@davegill86342 жыл бұрын
Nice Job on that Pal 👍
@westcoastprojects012 жыл бұрын
Thanks bud
@n2ghtowl2 жыл бұрын
So you used 2 litres of gel coat approximately what sort of coverage did that give you?
@thegreengenie2 жыл бұрын
Nice one mate
@cindyreid6404 Жыл бұрын
Thank you!
@JenkinsBoatWorks2 жыл бұрын
Good stuff, thanks
@westcoastprojects012 жыл бұрын
Thanks mate
@amishkeger2449 ай бұрын
Hey brother if you keep your roller metal peice on the side you’re pushing/rolling when you paint Ive found it to come out much better and Easier
@elliotcharlesworth46932 жыл бұрын
Are all 3 layers the same thickness as you said
@debradubose6055Ай бұрын
what gelcoat are you using? The blue gelcoat can? Manufacturer? Is it gelcoat or topcoat?
@LifeOnTheHulls2 жыл бұрын
Nice job mate,
@westcoastprojects012 жыл бұрын
Thank u
@mx-5claus5858 ай бұрын
Where did you got the GelCoat from? What kind of collor is it?
@dalepurcell7537 Жыл бұрын
What size of tin was the gelcoat for that boat
@antoniekruger86312 жыл бұрын
Thanks bro, that was a great video. Im a hobby builder with epoxy, not polyester, but I enjoyed this. Thanks for sharing. Is there no way of spraying on the gelcoat? I know that it is sprayed into the moulds before lamination.
@westcoastprojects012 жыл бұрын
Yeah I'm sure you can spray it on . Like you say its sprayed into tooling . Not sure what the texture would be like tbh
@neilfixes55012 жыл бұрын
You can spray it with a gravity feed gun using set-up pre-measured popcorn cups...it leaves an orange-peel finish. Use lightly waxed gelcoat so your sander doesnt clog.
@dudeleboski26922 жыл бұрын
I did the inside of my shower with gelcoat. I must of put it on too thick on top of the lamination coat, because a year later it started to peel off
@nigelmepham6355 Жыл бұрын
Did you put all three coats on in one go?
@kiwidonkeyk16562 жыл бұрын
That is helpful thanks, how do you keep the brush from going solid while you work?
@westcoastprojects012 жыл бұрын
Constant change of material on it. And a cup of thinners to wash it every now and then
@neilfixes55012 жыл бұрын
Keep 2 small containers of acetone handy to stand your brush tip in while faffing....one to wash out the resin, the 2nd kept cleanish for 'parking'.Good brushes are too expensive to waste.
@flightographist2 жыл бұрын
Best I have found! One question: what about the air barrier for curing?
@westcoastprojects012 жыл бұрын
The wax additive is already a part of the topcoat / flowcoat. If you have gelcoat your need to add wax additive for the air barrier . Hope this helps. Thanks for your comment
@flightographist2 жыл бұрын
@@westcoastprojects01 Thank you, you have answered another question...the wax version. hanks so much! You have assisted in splashing a salvaged impex formula kayak in Canada.
@Jonathanbaker Жыл бұрын
Wax or not to wax on a finish coat?
@ThePerfectSeason19722 жыл бұрын
Boat looks like a million bucks !
@James-cr5qx2 ай бұрын
Whats the normal process for under the water line? I have a boat with hundreds of tiny osmosis blisters, each one about the size of a pinkie fingernail. My plan is too lift, gelcoat plane a couple of layers ofbthe fiberglass. Soda blast to expose any deeper blisters ect. Then leave on the hard for a few months. Fix blisters, a couple of layers of fiber glass. Fill and sand anything uneven. Then i would like to know what else needs to be added to the hull before coppercoat or antifoul? Any tips are really appreciated
@westcoastprojects012 ай бұрын
Sounds like you have a good plan there. When you have done the topcoat just follow the instructions on what antifouling you choose
@haydenloader45292 жыл бұрын
Hi, great video. Just wanted to know the difference between gelcoat and flowcoat and if it has different applications?
@westcoastprojects012 жыл бұрын
Hi mate . Gelcoat is for application in tooling / mouldings . Flowcoat/ topcoat has a wax additive to help it cure
@snapbaitspredatorfishingch44522 жыл бұрын
also meant to ask will flowcoat give you a hard finish much like gelcoat,cheers great video
@neilfixes55012 жыл бұрын
Flowcoat is just heavily waxed gelcoat, usually made from resin approaching it's shelf life. Not for 1st or 2nd coats...the wax interferes with bonding, but it goes on thkcker and is easier to sand.(after 24 hrs)
@tubsworld-authorgerneldarr31062 жыл бұрын
Good Video 👍🏻👍🏻 Very Helpful🏆2022📆 New Subscriber from Bermuda Island🇧🇲🗺🌏 ...
@hopdjandy2 жыл бұрын
How far back do you need to sand for the gel coat to stick to? Can you sand down as in key it then apply or does it need taking right back to fiberglass?
@westcoastprojects012 жыл бұрын
If the coating your going over is sound then just give that a good key with 120 grit sand paper
@markramsden17722 жыл бұрын
Hi, IV got a little Avon sr4 rib and I'm wanting to tidy it up a little and thinking of re-jelcoating the hull now it looks like dirty old tea cup a bit yellow not the white it once was. Do I HAVE TO sand it down or can I just apply new jel paint straight on?
@westcoastprojects012 жыл бұрын
Just give it a clean and key it up ready to apply the new gelcoat
@qlder20202 жыл бұрын
hi do i need to add wax to gelcoat or more hardner was told to use flowcoat as gelcoat is for molds great video love the colour
@westcoastprojects012 жыл бұрын
I would use flowcoat or topcoat. If you have gelcoat definitely add the wax
@duncanwrigley37072 жыл бұрын
Useful vid thanks, what product did you use?
@westcoastprojects012 жыл бұрын
Was just a standard topcoat
@vincentdsnt2 жыл бұрын
When I apply gel coat for the best flowing coat I will use a red brick......with the brick in my hand i then pour gel on the the brick (not the side with holes) then rub the coated brick onto the finished glass ! OMG so much easier than a roller ! Trust me.
@triplecranks3 жыл бұрын
Quick question. I am applying gelcoat to a deck surface over fairing compound. The gelcoat I have has wax in it. Can I start with laminating resin for the first two coats and then finish with the gelcoat with wax?
@westcoastprojects013 жыл бұрын
Tbh I would get multiple coats of the gelcoat on . Reason being is you can cut and polish it back . With only one coat you will sand threw
@gregprider38433 жыл бұрын
No mate you need to sand back if you have wax iin the last coat before further gelcoating.
@triplecranks3 жыл бұрын
@@gregprider3843 Thanks for the info! I was thinking of wiping the surface down with acetone, then sanding with 80 grit then 120 grit sandpaper. I was going to wipe it down again with acetone and then roll and tip the gel coat. I do not have a tip large enough for spraying it and as little as I spray gelcoat, I can’t see spending the money on a tip as they are rather expensive.
@vivimu2 жыл бұрын
Will fresh gelcoat bond well to very old gelcoat? Or, do I need to sand off all the old gel down to the fiberglass ? Or do I need to prime the old coat first? I can't tell if you're applying the blue gelcoat to primer or sanded gelcoat
@westcoastprojects012 жыл бұрын
Hi mate . You can go strait over the old gelcoat as long as you have given it a good key to bond to . Go over it with 120 grit sand paper to key it up . On mine I'm going over tge original glass and body filler
@vivimu2 жыл бұрын
@@westcoastprojects01 My project boat is almost ready for new gelcoat whilst I am more than ready. Sanding sucks! Thanks for your tips hopefully I get some decent results like yourself
@neilfixes55012 жыл бұрын
Two-cloths solvent wipe + sanding to key the new coat + vacuuming. I would use 80-grit for a better key...gelcoat is so thick, sanding scratches wont show through, unlike lacquer or enamel, and you are going to finally fine-sand it anyway.
@guachingman Жыл бұрын
Superglue the base of the bristles where they meet the metal of the base of the brush, no more loose hairs on your gelcoat.
@pittythemillwrong50217 ай бұрын
is it non wax gelcoat or waxed? im getting ready to do my transom and i have to cut a part of my top cap off and then try and match the white gelcoat to the old stuff. so not the whole boat.
@westcoastprojects017 ай бұрын
It had the wax addive mixed in with it
@gedertonfc2 жыл бұрын
Ricky! Is it possible to gelcoat over a painted finish? It's inside my boat, it has some scabby paint over the fibreglass which has all but fell off. I could possibly sand the rest off but not sure if it would damage the fibreglass..
@westcoastprojects012 жыл бұрын
On the inside of one of my boats I had this same issue . I sanded off what I could and applied topcoat gelcoat over it all and so far it's fine . Didn't have any reactions or delamination
@gedertonfc2 жыл бұрын
@@westcoastprojects01 Cheers pal I will give it a go 👍
@brentmcmahon81882 жыл бұрын
Can you spray gel coat with a airless sprayer? Seams to me you would have a good shinny coat and you can put as many coats as you want. With a airless sprayer there is no over spray and no air means to air bubbles and a ver slick Finnish?
@westcoastprojects012 жыл бұрын
If u had a big enough cap
@farmer87yj2 жыл бұрын
helped me bigtime forsure ..i only really have one question ..what kind of tea do you drink
@westcoastprojects012 жыл бұрын
Warm and wet does the job lol
@farmer87yj2 жыл бұрын
@@westcoastprojects01 lmao just at the begining i think i heard you say lots of tea stuff lol thats why i ask
@SuperKimtuan2 жыл бұрын
Hi, I have a question how many qt gel coat do I need 4ft x 10ft? I’m doing the floor
@westcoastprojects012 жыл бұрын
Will give you coverage on the tin or data sheet of what you buy
@snapbaitspredatorfishingch44522 жыл бұрын
hi can you get a good finish by using flowcoat as a finish coat on the outside of the boat ??
@westcoastprojects012 жыл бұрын
Yeah mate
@jackdexter2147 Жыл бұрын
How would you paint a boat with a stripe down the side? Masking tape? Or is gelcoat too thick when it cures?
@westcoastprojects01 Жыл бұрын
Just mask it up and do it with the gelcoat
@mervynfuler Жыл бұрын
Hi mate I've got a 17ft wilson flyer how much gel paint will I need to do the outside
@westcoastprojects01 Жыл бұрын
It can vary with different brands and consistency. If you look on the info on the product it will tell you the coverage at different thicknesses
@mikebyford52582 жыл бұрын
What was the "cleaner you used prior to applying the topcoat? Also why didn't you abrade the surface I though oxidised gel coat would have little adhesion to new topcoat ?
@westcoastprojects012 жыл бұрын
I used panel wipe to clean the boat before I applied the topcoat. Not sure what you mean oxidised gelcoat . Every layer was keyed up
@mikebyford52582 жыл бұрын
@@westcoastprojects01 Thanks - I didn't hear a mention that the gel coat was sanded just the wipe as preparation . All gel coat is oxidised after exposure to UV and air after a few months . that's what I meant as polyester doesn't adhere to oxidised gel or any other poly ester . I thought from the video that you had used a special product that prepped the old gel coat without sanding .
@stevenclist66442 жыл бұрын
What brand of gel coat do you use as ive had mixed results from various types of gel coating, but love that colour
@westcoastprojects012 жыл бұрын
Will have to have a look lol . It's a local suppliers brand
@stevenclist66442 жыл бұрын
@@westcoastprojects01 definitely one of the better colours out there
@westcoastprojects012 жыл бұрын
@@stevenclist6644 yeah when I spotted I just had to have it
@Clover123462 жыл бұрын
Would a sponge brush work to smooth. It after the roller?
@westcoastprojects012 жыл бұрын
I don't see why it wouldn't. Only one way to find out lol
@GraemeJones19798 ай бұрын
Hello mate how many coats of gel coat did you apply to the boat, did you use a particular company for your gel coat supplies
@westcoastprojects018 ай бұрын
Hi mate . I applied 2 heavy coats . If you purchase gelcoat get the wax addictive or just buy topcoat . Any brand will be ok
@brandenandrews80512 жыл бұрын
Quick question, so I take it if you're putting on a gel coat onto fibreglass outside of a mould you add the wax solution into the mix for the final top coat layer for it to be able to be sanded and polished? As when I did more research it says that if you don't it will remain tacky and be unable to be sanded and polished?
@westcoastprojects012 жыл бұрын
Yeah thats correct buddy . Gelcoat needs the surface of a mould to cure. Topcoat or flowcoat has the wax additive in it . Or if your using gelcoat u as a finish u need to add the wax
@brandenandrews80512 жыл бұрын
@@westcoastprojects01 cheers, I thought so but was just checking as I'm not familiar with gel/flow coats, I've only done the actual laminating before. Are there any other finishing methods other than flow/gel coats?
@westcoastprojects012 жыл бұрын
@@brandenandrews8051 yeah you can paint instead of flowcoat / topcoat. There are many brands of marine paints . Even automotive paint
@markthomasson5077 Жыл бұрын
So you are Flow coating ….nor Gel coating!. Ps , good work….but no gloves!
@myparadiseonbantayanisland90302 жыл бұрын
Can you gel coat over a wood hull with enamel paint
@westcoastprojects012 жыл бұрын
I would suggest doing a test area to see if it reacts
@aandamar892 жыл бұрын
Nice work! I have a question, what is filler you recommend for polyester resin boat? Here, there only epoxy based filler in grey color, usually used for metal, body car repair. Is it recommended and can bond well? Or mix of the polyester resin with talc or aerosil is better for filler? Thanks!
@westcoastprojects012 жыл бұрын
I've just used car body filler
@aandamar892 жыл бұрын
@@westcoastprojects01 thanks!
@makingcookingfixing2 жыл бұрын
I've used car body filler on my dad's boat, and when the sun hit, it cracked all my repair work. It looked amazing and new the first week, and disappointing to watch the 3rd week. I basically have to do the job all over again, this time I am going to use, marine filler.
@aandamar892 жыл бұрын
@@makingcookingfixing thanks for experience! I'm still not tested the car body filler yet, but I believe what you told. I'm wondering it the car body filler will bond well to frp.
@makingcookingfixing2 жыл бұрын
@@aandamar89 I’m sure it will bond, now that I am thinking about it, I also used it on my car, and from the sun it cracked as well.
@gerardguglielmo16442 жыл бұрын
Funny how we all breath heavy with our own working sounds. Hughhhh, ohhh, shit, ughhh, breath heavy, repeat. By the way do you have ravens in the background? Nice work
@gotany12 жыл бұрын
when i work i tell who ever is around me "get ready for the sound effects".
@Luuxs2 жыл бұрын
what is the fastest way to sand off gelcoat? I have been trying it with my excentrik sander it takes 30min for a very small area i cant afford a 5k gelcoat planer do you have any suggestions
@westcoastprojects012 жыл бұрын
I used paint prep disks and flappy disks on an angle grinder . Very fierce and can easily cause damage that will need to be sorted with body filler .
@chhindz2 жыл бұрын
An air powered DA sander would be the normal with autobody work.
@Luuxs Жыл бұрын
@@westcoastprojects01 thanks for the answer right now i am using mirka deros 8.0 and its going pretty fast but i have done a test with a belt sander untill it starts to shine through and then sand it with the mirka the result is smooth and the fastest but also need to watch that you keep following the body lines of the boat
@NinoSpinner2 жыл бұрын
hello what product did you use to paint it? blue gelcoat? Io sono italiano ciao e complimenti
@westcoastprojects012 жыл бұрын
Hi there . Yes it was a blue gelcoat
@NinoSpinner2 жыл бұрын
@@westcoastprojects01 ok thanks
@1970swimmer3 ай бұрын
Can you apply gel coat directly over fibreglass?
@westcoastprojects013 ай бұрын
Yeah mate just make sure it's got a good key Check out my other vids
@benc657533 жыл бұрын
Did your gelcoat come with the wax added already? I didn't see any reference to having to add the wax additive.
@westcoastprojects013 жыл бұрын
I'm using topcoat. Wax already added to topcoat
@benc657533 жыл бұрын
@@westcoastprojects01 As I suspected. I just didn't want to assume anything.
@sander10162 жыл бұрын
So british accent, good vid, folk
@westcoastprojects012 жыл бұрын
Thank you
@LNM0000 Жыл бұрын
hi mate, did you get the brand of the stuff you're using ? Note ina comment way down about it but couldn't find an answer. Apologies if it did get answered.
@westcoastprojects01 Жыл бұрын
I got everything from these guys www.cfsnet.co.uk/
@christopherdougherty23122 жыл бұрын
I'm going to subscribe anyway. I have to see the results.
@jessebaker18832 жыл бұрын
Good vid. How long do you wait between the second and third coat?
@westcoastprojects012 жыл бұрын
If your going on same day you need to let it tack off . You should be able to touch it without your finger sticking to it . Or let it fully harden then key it up and then apply next coat
@makingcookingfixing Жыл бұрын
@@westcoastprojects01so did you do 3 coats? Does it mean that you used unwaxed gelcoat and used wax for the last coat? Thanks for answering, i finally got all the prep done , and tomorrow I’ll be doing this exact job. Thanks
@Gunsnstuff20022 жыл бұрын
What material is this boat I got I fiberglass one that needs redone
@westcoastprojects012 жыл бұрын
Fibreglass hull bud
@howardrice7280 Жыл бұрын
Thank you. What is Panel Wipe?
@westcoastprojects01 Жыл бұрын
It's like a degreeser to prep the panel
@tuzik17522 жыл бұрын
🙂🙂👌😁
@serviceproper2 ай бұрын
So you only put one coat on?? What if you put two or three do you just wait five minutes between coats?
@westcoastprojects012 ай бұрын
I did 2 coats on this . I left the first coat to fully harden so I could sand it flat . Second coat lays down better . Follow the guidelines on the material you use for drying times
@anthonyexmouth5 ай бұрын
How many coats did you apply before polishing?
@westcoastprojects015 ай бұрын
I applied 2 on this one
@KK-ol5ov2 жыл бұрын
I’m curious do you have to sand it between coats?
@westcoastprojects012 жыл бұрын
Only if each coat is left to cure . If you allow each coat to tack off you can then apply next coat directly on
@KK-ol5ov2 жыл бұрын
@@westcoastprojects01 thank you so much 👍
@justingeorge66553 жыл бұрын
If I have wax additive can I just add wax to the final coat or will the other layers not set up?
@westcoastprojects013 жыл бұрын
Your need to add it to all coats . Standard gelcoat is for tooling . Laying up in molds .
@justingeorge66553 жыл бұрын
@@westcoastprojects01 thank you! Does that mean I need to sand the wax off between each coat?
@westcoastprojects013 жыл бұрын
@@justingeorge6655 no mate the best way to apply is wait till the previous coat has tacked off then apply the next coat . Or let each coat go off then key with like 120 grit .
@justingeorge66553 жыл бұрын
@@westcoastprojects01 awesome thanks for the advice I really appreciate it!
@westcoastprojects013 жыл бұрын
@@justingeorge6655 no trouble mate . If your waiting for it to tack off you should be able to touch it and not stick to it . Then put the next coat on
@juantwo322 Жыл бұрын
So one brush to one cup of gelcoat ?, because the brush stiffens up ?
@westcoastprojects01 Жыл бұрын
The brush will last all the time your using it and keeping material moving .
@miyashelest77952 жыл бұрын
🤗🤗👍👌👍
@azmike19562 жыл бұрын
Or a verb if you gelcoat something.
@andrewvisser580511 ай бұрын
Would it not be easier if the boat was upside down? Looks like your shed is big enough to flip it..
@TheBurntSportsman Жыл бұрын
Would a HVLP machine work woth gel coat??
@westcoastprojects01 Жыл бұрын
Possibly if you had the correct size nozzle on a gun
@christopherdougherty23122 жыл бұрын
I would have sprayed one coat on the whole hull in 12 minutes ,boss. How are you going to sand that out??
@westcoastprojects012 жыл бұрын
I could have sprayed it as well boss . I have all the professional equipment to spray . And sanding out was easy . Check my other video how to cut and polish . The idea of the video was to help people without all the equipment
@christopherdougherty23122 жыл бұрын
@@westcoastprojects01 I like all your videos .. all these other guys try to make it fancy.. this job is a mess lol
@abdullahgamezer95167 ай бұрын
هلو الذي نحتاجه هو كيف نصنع الجليكوت وماهي نسب المواد المخلوطه وشكرا
@matthieugabri9981 Жыл бұрын
Composition gel coat de finition
@JuanMiguelGarcia19692 жыл бұрын
😳😨😱 exactement ce qu’il ne faut pas faire but it.s funny