No video
How to get GPS from Flite Test EZ-ID to Betaflight
Рет қаралды 1,689
Күн бұрынHere are the exact steps you need to take to get GPS location data from the Flite Test EZ-ID Remote ID broadcast module into Betaflight so you can use the coordinates for return to home, display on your OSD, etc.
Step 1: Wiring diagram is incorrect. Connect second pad from left (when looking at the back of the board) to a RX pad on your flight controller.
Step 2: Update to Betaflight 4.4.3-zulu ( or anything newer ).
Step 3: Enable MSP on the UART you connected the wire to.
Step 4: Enable GPS and select MSP.
If you have issues getting MSP enabled on the right UART and MSP enabled for GPS at the same time, have a look at this: github.com/bet...
#remoteID #ezid #ftezid #betaflight
@MCsCreations 10 ай бұрын
Thanks for the info, dude! 😊 It's great to see you back! Stay safe there with your family! 🖖😊
@donaldheon 10 ай бұрын
Excellent! Thank you for the video. the pinout diagram was a nice touch for use that cant locate it.
@Stormin13 10 ай бұрын
Thanks pal - I've been struggling with this
@5zero7RC 10 ай бұрын
Yeah, it wasn't easy and I had a lot of people help figure out all the issue. Glad I could help!
@cjstewart7979 5 ай бұрын
Hey there! Thanks for putting this together. I have an issue, hoping you can help. I don't have an option in BF10.10 for a 4.5-zulu firmware and I absolutely cannot get GPS to work on 4.5.0-RC2. Any idea what's going on?
@BuddsSkyCam 8 ай бұрын
There should be more shown in the gps tab. The gps tab should have info about each sat and yours is greyed out like mine. Once i switching to a separate gps from the ezid i then was able to see the data from each satellite in the gps tab. The way you have it setup does not work correctly and you will have your home point off even if you have 20 satellites.
@BuddsSkyCam 8 ай бұрын
Tried RTH and today and even though i had 20 satellites and it registered my home point this gps would not work correctly to fly home. Has anyone had the RTH function work via msp? Im thinking there is a lot more work to be done here.
@MystikSquash 5 ай бұрын
Can this be powered by the 3.3 pin output?
@BuddsSkyCam 8 ай бұрын
You have the m8 version right? I got the new m10 version and am only getting 5-6 satellites and according to bardwell you need to do an update to the m10 for it work correctly. Do you know anything about the new m10 flit test module?
@5zero7RC 8 ай бұрын
Yes, I have the m8 version of the EZ ID. As far as I know the m10 that is part of the EZ ID should have all the updates applied before it was shipped.
@BuddsSkyCam 8 ай бұрын
@@5zero7RC this is the update, i think its because of the way betaflight is working with the m10 where the m8 already has everything correctly updated. kzfaq.info/get/bejne/a8xyd9SWptXVpn0.html
@TheMoonwatchers 8 ай бұрын
@BuddsSkyCam sort of BF4.4.x has too many dev mistakes and no support fro the M10 so it takes far longer for cold start. Use the better and safer BF4.3.2; GPS rescue is unsafe on BF4.4x in our opinion and we pulled it from all iFlight product that uses GPS - wait for BF 4.5 with full M10 support or just use BF4.3.2 that doesn't slow cold start as much on the M10. 4.5 is RC1 now release should not be too far. and its amazing with return to home and fast M10 support. too.
@BuddsSkyCam 8 ай бұрын
@TheMoonwatchers i was talking on the bf discord and was able to get 4.5 zulu updated yesterday morning and i went from 6-8 sats sitting in my house on 4.5 rc1 to now 10-12 on 4.5 zulu just have to make sure barometer is off. They are working on it but 4.5 zulu with baro on and gps on, the gps will not work. Spent all day yesterday chasing that issue, after the day before there was an msp issue when using gps but its working really well today and i hope to test the gps tomorrow in a bigger area.
@BuddsSkyCam 8 ай бұрын
What do the other pads do in the row of 7? Is there another ground and power?
@5zero7RC 8 ай бұрын
Not sure, but probably for the manufacturer to install firmware.
@BuddsSkyCam 8 ай бұрын
Any Idea why when I select mps for my uart2 that its on that it removes everything selected from the ports tab?
@5zero7RC 8 ай бұрын
If you try to enable MSP on a 3rd or maybe it is 4th port, it will reset all the ports. MSP is not supported on that many ports. That's my first guess.
@BuddsSkyCam 8 ай бұрын
@5zero7RC i was going between your video and bardwells on gps m10 and i was selecting gps in tve ports tab after i clicked msp and that caused it to reset it.
@BuddsSkyCam 9 ай бұрын
Have you tried RTH with that setup on betaflight? Are you using this same method for INav?
@5zero7RC 9 ай бұрын
I have never tried to use INav. I have not yet tried RTH, but I do get good GPS coordinates in my OSD, so I assume it could work normally.
@BuddsSkyCam 9 ай бұрын
@5zero7RC wish they made these with the m10 gps.... would be cool to see how accurate it is with RTH is with the rfid. Thanks for make thia post you are the only one i have found to have and do this
@BuddsSkyCam 6 ай бұрын
Have you been able to test out RTH yet over mps?
@5zero7RC 6 ай бұрын
I have not personally tested it, but I know others have, but you may need betaflight 4.5 for it to work... github.com/betaflight/betaflight/pull/13269
@BuddsSkyCam 6 ай бұрын
@5zero7RC yes i have tried it on rc2 4.5 and 4.5zulu.
@BuddsSkyCam 5 ай бұрын
@5zero7RC can you share any videos of it working? I cannot find anyone who has made it work and i just tried it again on a 3rd drone on 4.5 rc2 and the drone gets lost and cant find home
@DrDroneFilms 3 ай бұрын
@@BuddsSkyCam I'm having the same problem as you! I can get the GPS tab to partially work with GPS over MSP, but still can't see the quality of satellites. Whenever I arm (making sure I have plenty of satellites, usually 12+!), the OSD warns "RESCUE N/A", which means I GPS rescue won't takeover in the event of a true failsafe. When I activate failsafe via switch, it just hovers in place for 20 sec (and is of course blown by the wind) due to sanity checks. I noticed that telemetry and betaflight will recognize the number of satellites, but my OSD always says "NC", which I'm guessing means that the OSD parameter, which must be different than telemetry (?). Perhaps there's something there on why GPS rescue isn't working when using GPS over MSP with the Flite Test EZ ID. I opened a bug report on the betaflight github page, but I don't think the developer understood my problem. I'm curious what you think. github.com/betaflight/betaflight/issues/13484
@Sergio10795 Ай бұрын
@@BuddsSkyCam any luck finding someone who has made it work? I'm currently trying to figure it out myself
@PremiumK9Krunchies 7 ай бұрын
Its pretty cold today.. take out the drone?
@5zero7RC 7 ай бұрын
No, I have not flown much lately. Too busy riding my fatbike in this nice cold weather. :)
@PremiumK9Krunchies 7 ай бұрын
@@5zero7RC That's awesome, I'm on the Mississippi near Albertville. And it's literally frozen over and not moving as far as visual. I took my drone out for some video I might post a short later
Andreas Spiess
Рет қаралды 547 М.