✅How to Get Rid of or Turn Off the TPMS ⚠️ Indicator Light (Blinking then Solid) on a Toyota Tundra

Рет қаралды 52,922

Жыл бұрын

✅➜amzn.to/3Dp1cFQ, TPMS sensors can be costly and may not fix your situation. In today's video I'm going to show you how to get rid of the blinking or solid TPMS warning light on your dashboard. My TPMS sensor would blinking serval times then stay on solid and never turn off.
✅Red Quick Splice Connector ➜amzn.to/3WjI3Ob
I have a 2012 Toyota Tundra and had this issue for 6 months now. I had the tires check and pumped to proper specs, checked my spare tire pressure because it had a TPMS on it, I had the TPMS system reset and checked, I had the TPMS module and receiver checked and no resolution so I went with this disable bypass option that you see in my DIY video.This should work on 2007-2013 Toyota Tundras as well. Comment below if you tried a similar solution and it worked for you. Ever since I had my truck I rarely even use the TPMS system because I check my tire pressure on a regular basis. If the TPMS light comes on it could mean you have low pressure, high pressure, TMPS sensor batteries are low, or TPMS sensors have to be reprogramed. The TPMS system on this truck is useless really because if the dashboard TPMS indicator comes on you don't even know which specific tire is low or high or even which side it is on.
DISCLAIMER: This is a demonstration of a modification I did on my truck. Not responsible for any mods that you perform on your vehicle.
✅Visit ➜funtechreviews.com to support the channel! THANK YOU!
#TPMS #Toyota #Tundra

Пікірлер: 109

@VibrantDeals Жыл бұрын

*✅Red Quick Splice Connector ➜**amzn.to/3WjI3Ob* *✅Visit ➜**funtechreviews.com** to support the channel! THANK YOU!*

@billsherrill6571 Жыл бұрын

Thank You, Thank You. Wow! This fixed my problem. 2007 Tundra SR5 CrewMax 5.7 After dealership changed my TPMS sensors, it was determined to be my Receiver. Receiver was ordered 8.5 months ago and has been on backorder. I had to pay for Receiver when they ordered it ($801.38 with tax) and I was then told it would be $319.90 for them to install. My TPMS light would come on only after I had driven for 20 minutes and then stay on. The light would go off after it was parked over night. Tried this and worked. I made 2 thirty minute trips to confirm. Now, the TPMS light will show up for a split second when you turn on ignition (not as long as before when turning key switch on). I called the dealership and they refunded my money. This procedure is very easy to do, just make sure the insulation has been broken on both wires when it is clamped. My first try, one of the wires was not making contact through the clamp. This video/suggestion saved me over $1,120.

@VibrantDeals Жыл бұрын

Extremely glad to hear that. This is why I made this video. Happy to save people time and money!

@bradluebke6922 5 ай бұрын

Dude, you're a rockstar! '07 Tundra Limited, worked like a champ! You have no idea how thankful I am!

@hd607ny 4 ай бұрын

i have a 2010 tundra , worked like a charm .... Great Video , Good job

@darreltomberlin1242 Ай бұрын

Thank you.! Worked exactly like the video.! 2008 DC long bed.

@darrylshafer8473 8 ай бұрын

This worked perfectly for my 07 tundra, and it took about 2 minutes. Thanks for the help

@VibrantDeals 7 ай бұрын

Glad it helped

@timspratling9404 Жыл бұрын

Thank you so much! This worked perfectly for me. I was quoted $240 at the tire store to replace the tire sensors. 2007 Tundra.

@VibrantDeals Жыл бұрын

Awesome! Glad to hear that. Thanks for sharing your experience.

@risajajr 3 ай бұрын

Thanks for the excellent video! This worked for my 2011 Tundra. All of the steps are exactly as you described, with one exception: my dash panel had 4 clips that had to be released, not 3. There is one behind the left post (the one you just popped out). In fact, we can see that clip on your panel too (@0:37), above the vent opening. Also, you can release the tabs with your fingers (if you have fingernails). In my particular case, one of the clips could not be easily released because the clip had been deformed so that it was very hard to access it. It took a lot of finagling with a screwdriver to basically push it straight up (i.e. somewhat straightening it) in order to get the panel out. But that was the only hard part for me. After that, everything was gravy.

@3131960dan Жыл бұрын

thanks for the great how to! super easy mod! did it in less than 10 min on my 2010 Tundra!

@VibrantDeals Жыл бұрын

Nice work! Glad to hear that! Thanks for sharing your experience.

@jiavang7748 Жыл бұрын

Thank you very much for sharing it's work for my 07 toyota tundra double cab. Your video was really helpful.

@VibrantDeals Жыл бұрын

Awesome!

@alexarnold174 Ай бұрын

Great video, i just forwarded to my neighbor across the street who's been online for days copying schematics and other hacks that absolutely don't work. He had it fixed within ten minutes of receiving this video. Thanks so much.

@timflippymorris Жыл бұрын

thanks soon much. very helpful. great job with step by step.

@VibrantDeals Жыл бұрын

Glad it was helpful!

@spicythai2000 2 ай бұрын

Good informations. My stay on but doesn't bother me. So I will do what you did. Thank you.

@adamo4904 10 ай бұрын

Thanks a ton. Worked perfect on my 2009.

@VibrantDeals 10 ай бұрын

Great!

@jimgow4991 Жыл бұрын

Thanks! Worked like a charm!

@VibrantDeals Жыл бұрын

Excellent!

@gregvanzant8275 11 ай бұрын

Thank you

@user-uf2tq4nq1b 7 ай бұрын

اشكرك نعم فعلت هذا كان فعالا.

@kayborn1076 Жыл бұрын

Thank you best video I found on this problem that light been driving me crazy 5 min fix no more light 07 tundra. Thxs again!

@VibrantDeals Жыл бұрын

Glad it helped

@imquattro Жыл бұрын

Confirming -this works! Ref: '07 Tundra No TPMS light anymore! Thanks!

@VibrantDeals Жыл бұрын

Good to know. Thanks for the feedback!

@vitabona5 Жыл бұрын

Works perfectly on a 2010 Sequoia. Thanks!

@VibrantDeals Жыл бұрын

Great!

@TerpyTheTundra 4 ай бұрын

Thank you very much

@shadowshadow6326 Жыл бұрын

Thank you so much for video and go working this tomorrow in the morning and tell you more detail what's going on thank you happy good night

@VibrantDeals Жыл бұрын

Thanks for the feedback. Glad I could help! Let me know how your project turns out.

@colemanhorner Жыл бұрын

How'd it work out for you?

@sergioalmanza4316 6 ай бұрын

👍 Thanks a lot 👍

@abc33944 3 ай бұрын

Gonna try this on my 2020 Camry hybrid

@howardheater9131 8 ай бұрын

Thank You!!!

@VibrantDeals 7 ай бұрын

Very welcome!

@ElPrimoNuni1960 Жыл бұрын

Good Yob🎉

@liemtruong2982 Жыл бұрын

Thanks!

@VibrantDeals Жыл бұрын

Thank you much! I highly appreciate your donation!

@rudylucas8791 Жыл бұрын

Thank you very much for your video…very informative. It helped me to disable the tire pressure light for 2008 Toyota Tundra 4.7l V8.

@VibrantDeals Жыл бұрын

Glad to hear that.

@brandonalbracht5209 Жыл бұрын

Thank you great video

@brandonalbracht5209 Жыл бұрын

Worked perfectly no more light

@VibrantDeals Жыл бұрын

Nice, I have 3 other friend that tired it out and it worked.

@KarlNettgen 11 ай бұрын

This worked perfectly for my 2007 Tundra. I noticed when I got the truck that two of the wheels didn't even have the sensors installed on the rims. The tires were new! So, instead of expensive repairs or splicing into the factory wires, I simply installed a small strand of copper wire jumping the back pin side of the connector. This is easily reversed and does not damage the wires either. Thanks for the great info! Now there is only a quick flash as the ignition key is turned to the start position and then the light stays off!

@voodosforever 9 ай бұрын

You are obviously a person of great intelligence! It is never a good idea to use. Scotch locks plays connectors because they cut the insulation and allow moisture intrusion into the wire, which, for corroded in addition to the scotch lock splice connector, potentially cutting the copper conductors, which will be damaged further by the corrosion if you don't cut the wire off and completely. Your idea of the jumper in the back of the connector is perfect, and something that I have done for years - I save old fluorescent light ballast wiring for just such purposes: it makes a perfect light gauge jumper wire.

@mattdaniel2395 2 ай бұрын

And your crusie control works with it off correct?

@thepoastman209 Жыл бұрын

Thanks my man definitely works for a 2011 Toyota but I ran into a problem with the splice connector not cutting deep enough into the wires had to really jiggle pull and pry on them to make them contact the connector

@VibrantDeals Жыл бұрын

Nice! Great insight thanks for sharing your experience.

@voodosforever 9 ай бұрын

And call mentor very recently suggested simply using a jumper wire from the blue to the yellow wire/yellow to blue wire either either or in the back of the connector: I save the solid wires off of old fluorescent, light ballast, or just such purposes. you push one wire end on one side and the other end of the wire on the other side and you have "Jumper" the connection - as the commentor pointed out, simply pulling the wire back out, returns to the original condition and there is absolutely no damage to the wiring. The problem with those 3M scotch locks places as they cut through the insulation and potentially the copper wire and can lead to corrosion which will ruin the wiring. Believe me, I am 64 and I can tell you stories.

@CarlostheBarbarian Жыл бұрын

Works on a 2007 Tundra SR5. There was no cover on mine, wires are same color/orientation and TPMS box in same location. Thanks!

@VibrantDeals Жыл бұрын

Cool!

@mattdaniel2395 14 күн бұрын

Have a 2010. Womt go off even woth reset. It disabled the cruise control which is the worst. Will this allow the cruise control to work again?

@eleazararauz5413 10 ай бұрын

This TPMS crap is stupid, replaced two sensors, discount tire charged me 80 bucks just for installation they couldn’t program it, then took the truck to the STELALERSHIP wanted 220 bucks for the programming 😢 I’m not paying over 300 dollars to replace two stupid sensors Thanks for the video I’ll try this I done it on my 4Runner wich have one on the spare tire also, and never had any problems!!

@stevec9669 Жыл бұрын

Thanks much. It works on my 2009 4cyl RAV4. I see you borrow the yellow wire (red in my RAV4) to power the light blue wire (pink in my RAV4). Just curious, what stuff is usually powered by the yellow wire?

@VibrantDeals Жыл бұрын

Thanks for the feedback! Good to know it works on that year RAV4.

@javiermoreno7746 2 ай бұрын

Is this just for tundra? I have a 2009 ford f150 with same problem

@sundownbelow 3 ай бұрын

I did this with my 07 Lexus ES 350 and it didn’t work, I saw another forum saying that on my vehicle I need to connect the orange and dark blue wires yet after doing so my TPMS light is still on. Any tips?

@AGCampagna Жыл бұрын

I like it. What year is your tundra?

@VibrantDeals Жыл бұрын

2012

@Halfflip 6 ай бұрын

Mine didn’t work. Should I double check to see if I need to grip harder onto wires?

@sundownbelow 3 ай бұрын

Thanks so much! I’m using this on my 2007 Lexus ES 350 and wanted to ask, there’s some soft grey padding right above the wires and it’s not giving me enough space to connect the two. Is it safe to remove this type of insulation or at the very least cut some of it back to have more room to connect the two wires?

@sundownbelow 3 ай бұрын

I see in your video you do not have this padding, does this mean you removed it or perhaps your Tundra came without it?

@billygreenwood4004 Жыл бұрын

Will this work on a 2021 Tundra?? And would it be the same gauge wiring and same blue and yellow wires? Having the same problems, thx

@VibrantDeals Жыл бұрын

Not sure but you could try it and then just rewire it back it doesn't work? I don't know of anyone with that year that has tried this method out.

@Halfflip 3 ай бұрын

Hello, I did everything but still on? Should I try again? Any ideas? Thanks

@frederickespanol7007 Жыл бұрын

can I just put a jumper wire at the connector between those 2 wires. so I don't need the splice connector ?

@VibrantDeals Жыл бұрын

Not sure but that should work because that is essentially what I did.

@adkuenaso 3 ай бұрын

Bro thanks for video saved me a lot of $$$. The receiver is like $500 or something like that. I didn’t use that splice connector though I just spliced the two wires and black taped it and all is good. It was on a ‘08 Tundra with oversized tires btw. Thanks Again, TC.

@MrBikedrummer 9 ай бұрын

Any idea if this will work on an 08 Chevy Impala LTZ?

@VibrantDeals 9 ай бұрын

Not sure but maybe someone can give some input.

@sellmycar44 Жыл бұрын

Will this work on 2014 sequoia? And thanks

@VibrantDeals Жыл бұрын

Not sure honestly but what I have done is easily reversible. Mine still works perfect.

@Almighty7266 Жыл бұрын

Currently having this problem with my 2011 tundra they told me 2 of my tire sensors were bad but I’m thinking if I just replace the 2 sensors wouldn’t the light go away

@VibrantDeals Жыл бұрын

It should go away if the sensor are bad but if it doesn't then it is costly. Especially if the sensors don't resolve the problem. Up to you. Let me know how it plays out.

@edlyli7166 Жыл бұрын

Now I can upgrade my wheels

@VibrantDeals Жыл бұрын

Nice!

@navidsoroush8777 7 ай бұрын

Does the red clip thingy basically disconnect the blue two wires? Is that how this was done?

@im2yys4u81 3 ай бұрын

The wire splice splices the wires together without cutting the wire.

@mlopez1007 Жыл бұрын

You know, I wouldn't mind this idea, however I'd do this to a wiring harness extension to what's already there. That way I don't fudge with the original article, and it does give me the option to try and repair it later. That being said, anyone here have any idea as to where I can find something like that for this issue? It's happening to my '11 Tundra right now.

@Couchlover47 10 ай бұрын

This is a good idea. Did you ever find an extension?

@miguela.santiago4292 Жыл бұрын

Quisiera recibir instrucciones para apagar permanentemente o deshabilitar la luz TPMS en una Tacoma FJ cruiser 2007. Gracias.

@stmckevlin 6 ай бұрын

I have a 2013 Toyota Corolla. Are the 2 wires I'm splicing together the same as this Toyota Tundra you're doing this to in the video?

@johnp7551 Жыл бұрын

Correct me if I'm wrong, but its not the color of the wires that matter, but the locations in the connector?

@VibrantDeals Жыл бұрын

Both are important. You can move the connector up or down but they must make good contact with the splice connector to join both terminals.

@spookerr 4 ай бұрын

Is this disable method un--doable? Incase you have to revert back to TPMS?

@VibrantDeals 4 ай бұрын

Yes, both wires will be split. Just have to reconnect & insulate.

@RM..... Жыл бұрын

Hmmm,on the tundra forum ,they say to cut the light green and splice to the yellow. You cut nothing and just connected the 2 and it worked.

@VibrantDeals Жыл бұрын

I have no issues & have other friends with Tundras with no issues. Took it for an oil change recently at my local Toyota dealership & no codes/problems.

@mattsivert2594 6 ай бұрын

Or buy a black sticker an cut out a circle or what works best and place over indicator lol

@ukraineboy21 Жыл бұрын

Don’t work on my 2010 tundra 😢. Any other options?

@VibrantDeals Жыл бұрын

Sorry to hear that. It worked on my friends 2007 Tundra. You can try to put proper air in tire and reset the TPMS. You can try unplugging the battery and see if it goes away once you reconnect the battery.

@billsherrill6571 Жыл бұрын

Try it again and make sure the insulation is broken through on both wires with the clamp. The wires are so small that the first time I tried, one of the wires was not making connection because the insulation was not pierced/broken on one.

@ukraineboy21 Жыл бұрын

@@billsherrill6571 yes that was an issue. Now no light

@billsherrill6571 Жыл бұрын

@@ukraineboy21 Great, glad I could help

@VibrantDeals Жыл бұрын

Very true. Insulation must be broken to create proper contact.

@MrTexas2A 5 ай бұрын

I clipped mine 3 days ago and it went away. Just came back on today. Has anyone else had this happen?

@danielwiggin2982 2 ай бұрын

This did not work for my 15. Anyone else experience issues?

@nicolagiannini9847 10 ай бұрын

spend few dollars ,ask someone with programm pc to connect to your car and disable tpms light. thats all no ore light on

@nfpsrocketiptvftaiksdonati4954 6 ай бұрын

Did not work for me....2011 4.7 Tundra

@yz250brett Ай бұрын

Hello, not sure if you got it to work. I had the same issue with an 07 Crewmax. I even took the splice connector back off and saw the wire coating had been nicked by the splice. I decided to try it again, being certain to really crimp down on the red connector and ensuring both wires went through their respective sides. Sure enough , it did work. I saw another guy use a blue splice connector , but that is way too large for the fine wires on our trucks. Hope this helps.

@albertoaguilar704 11 ай бұрын

Disabling is not fixing the problem/ I hope the people thanking you know that😂😂 I would have just put duck tape over it if the light bothered me that bad 😂

@adamharris2674 8 ай бұрын

Thanks Dudley-Do-Good. I think everyone here knows what we are performing..

@im2yys4u81 3 ай бұрын

Depends on how you look at it. TPMS is a PITA and a useless feature for someone who checks their tires. I don't require an idiot light to tell me when my tires need air. I managed to operate a vehicle for 50 years without a TPMS monitor before the government decided I needed one. Imagine that.

@howardheater9131 8 ай бұрын

Thanks!

@VibrantDeals 7 ай бұрын

I highly appreciate ya!