Ten minute rambling tutorial on oil modifications. Thanks for watching .
Пікірлер: 31
@SonOfLiberty19843 жыл бұрын
I don't know how long I've been fighting with these damn things. Great vid! I appreciate it.
@cgriebel1 Жыл бұрын
Doing this trick tonight on my '94 029. It barely keeps a 20" set up lubed in the current (oem) trim. All I'd need is 15%. Thank you Sir!!!
@sonofthunder.3 жыл бұрын
nice i modded my stihl 034 036 piston ,and passages ,i appreciate your video
@chrisradla9 ай бұрын
AMAZING, amazing truly
@climbe44223 жыл бұрын
Never new you can do that. Thanks mitch
@thomasgronek6469 Жыл бұрын
In the event that one way overshoots the limit mark, can an extra washer be installed between the spring and the gear to compensate for the overgrind ? Thanks for the video.
@WeThePeopleUnited2A9 ай бұрын
Would like to see before and after oiling
@tonyd682110 ай бұрын
I bought an Husqvarna chainsaw 365 I was told it was OK but the one who gave it to him said it was not used for a long time ...there were a few things missing that I replaced them , as well the oil pump the carburettor gaskets .and fuel lines ...it started and I used yesterday to cut a fallen tree ...it went OK To day I tried to start again but no success after many try it would start but would die very soon ... Could you have any idea where to have a look for the trouble ? Your help is very much appreciated if you can . Thank you
@Witschor3 жыл бұрын
Hey, very usefull lead. Thanks
@montestreecutting91523 жыл бұрын
Nice video . Makes perfect sense to me.
@nickywalsh84923 жыл бұрын
That cotter pins kinda difficult to get out I find, on the 450 the plunger/piston is just push in as you know, I've used a flat file to on the flat end on those type have you?...a great vid would be to cure a saw that leaks when sat... Some mine do some don't, the ones do I've had success and failure...
@mweba13 жыл бұрын
O ring on plunger shaft. Requires machining.... I let em mark their territory.
@simpsonkid1003 жыл бұрын
Great information. Thanks for that A1 ✌🏼
@GrizC2 жыл бұрын
great video thanks ...
@arturtavares50308 ай бұрын
I need a oil pump for oleomac 942 chainsaw
@mspahn1967 Жыл бұрын
On the adjustment screw itself. Is the oiler all the way open when turning adjustment screw clockwise or counterclockwise?
@mweba1 Жыл бұрын
CC
@husky2683 жыл бұрын
Good vid Thanks
@sudburyhouse2 жыл бұрын
I have a husqvarna 440e that doesn’t oil the bar very well. I took it apart and the oil comes out when I run it without the chain. I also cleaned out the holes in the bar but it doesn’t oil it and I don’t see an adjustment screw. Any idea wtf is wrong?
@scod39082 жыл бұрын
clean out the ridges in the bar, and the passage from the hole
@acpfunnylunches3 жыл бұрын
If I sent you a new still in the box 7310, would you be interested in doin some work on it?
@mweba13 жыл бұрын
Yes sir. Do quite a few of them. Mweba10@gmail.com
@GrizC2 жыл бұрын
will this or on a husqavarna 77 also ?
@GrizC2 жыл бұрын
will this work on stihl saws also?
@mweba12 жыл бұрын
Yes
@bobeden50272 жыл бұрын
Goodonyamate!
@1d1hamby3 жыл бұрын
That doesn't look like it operates the same as my MS362.
@mweba13 жыл бұрын
Same principle with an overly complicated oiler assembly
@sagerman6779 Жыл бұрын
Much appreciated topic. I'm looking to experiment with filing the flat spot on the other end slightly larger. Has anyone had any experience with this mod? Are there any other ideas to increase the output of these pumps I may not have thought of? Thanks again for the video.