For sure it's definitely a great upgrade pitty it took so long but better late than never I guess!

No problem at all!

Thankyou :) Much appreciated!

Thanks! Glad I could answer that one haha. It was a customer's car so I won't be able to do pros and cons overtime unless they tell me anything haha but so far haven't had any issues installed a few of them at current time now. Pretty good upgrade from what I can see :) One thing I did notice is that when the car was off and door open is the door lock and door light buttons wouldn't adjust but there is a setting for retained accessory power so I would think that would do it but haven't played with it myself

There's another KZfaq vid that shows the trip fuel etc on screen working fine..

Yes for sure it's been a long time in the making but better late than never!

Thankyou very much :)

Hey. As for the transceiver, I have no idea sorry, as far as swc younonly need one or the other either the 3.5mm jack or the 3 key wires. Have to make sure the swc and head unit loom are connected before connecting the main power. I'm not familiar with all pioneer models but a lot of pipneers need to follow this step to work: turn car on on the head unit touch the screen where you go through the sources and drop down to source off once on source off but head unit still on then go to settings, I think system or one of those then steering wheel controls and click with adaptor then it should work. Also from memory the ba bf kit has dip switches on the back of the module that you have to switch I think pin 1 if using a pioneer unit so check that also its in the manual though if it's required. Hope this helps

@@D2iAuto thanks heaps mate, I was just about to comment on my original comment about the SWC issue, I double checked everything you just mentioned (those dip switches are ridiculously small 😩🤣) turns out some idiot (me) plugged the jack into the wrong socket hahaha, total rookie mistake 🤪 I found your website so I’ll give you a call shortly, will buy some stuff off you, just gotta save a few more $$, (I’ve rebuilt the suspension & brakes as well, which set me back $5k)…. Need new speakers & sub, my new HU has 4v pre out as well so I might ditch the factory amp for a decent power amp as well…. (Surprisingly the factory amp isn’t that bad , but being 18yrs old I dare say it will shit itself eventually) Thanks again mate, much appreciated 👍

@haydarmstrong8649 no problem at all. Glad you got it sorted 😁

That is for the comment! Yeah definitely been a long time.in the making. Still plenty of them around though every week I work on one on average but yeah would have been good if it was released a long time ago

Great vid thanks. What Sony head unit did you install? And what would you recommend I buy for my BF wagon?

Thanks, I'm in Ballarat Victoria so about an hour or so north of Melbourne city

Thanks! There should be a pink wire on the harness that either says vss or speed that gets connected to the head units speed sensor wire

You'll have to purchase the secondary harness so Sony to iso unless you are happy to cut and solder the wiring in which case you'll just cut the ISO connector off and solder the supplied Sony bare ends harness to the facia kit loom :)

The central locking, trac control and interior light button are part of the new air-conditioning switch panel the buttons are all still there. The trip settings are accessible through the menu from the infodaptor it's all still functional. Also this is an install video it's not my product feel free to check out aerpro fir more information

You'd have to pull the unit out and check the wiring at the plug to confirm you don't have power there then probably trace it back from the plug. Or pickup an accessory switch elsewhere and wire it to the unit trigger. Its something i can really say this or that unfortunately. My best advice would be take it to a shop or auto elec

@@D2iAuto thanks mate, 2 things I was leaving to last, pulling it out, and budget's a bit thin atm for sparky. It all points to a fuse, is there anything in the actual internal switch?

It's a sony ax3200 head unit and yes it's a plug and play harness

Hey, It should all be data on the canbus line so no extra plugs should be needed. I have done a few of these since the video and the temp display has worked on them without any dramas. Out of curiosity what model is it that you changed over?

@@D2iAuto cheers mate, sounds like the temp sensor's faulty in that case. It's a 2009 AWD Petrol Ghia, had the Aerpro kit paired with an Alpine iLX-W650E. Was told that the Sony would be too deep for the Terri, but I see you've installed a Sony here.

@@ashwynfernandes Hmm may have something to do with the Ghia variant potentially i haven't done a Ghia as of yet but yeah not too sure on that one. Yeah half chassis is recomended, the sony units are a single din but almost a 3/4 chassis but they just fit especially if you remove the plug as shown in the video that gains another 20mm or so the sony unit wouldn't fit without doing that :)

Check out the Kenwood range would be my recommendation. A lot of the new kenwood line are all short chassis so work perfectly with this facia kit. The dmx5020s would be a good starting point for wired carplay or the dmx7522 would be a good starting point for wireless carplay then the dmx8521 for physical button compared to touch buttons

Hey, yeah any of the Sony mechless units should work. Or Kenwood dmx5020s Clarion fx450 Grundig gx3800 Anything similar in size should be fine

@@D2iAuto Thanks for taking the time to reply Have you installed any of the units you have mentioned or just the Sony?

@@leslesbo4049 no problem and yeah have installed 3 different Sony models the Clarion fx450 Kenwood dmx5020 and grundig gx3800 there would also be a few alpine units that would work I'd say. If it's half length chassis it will all fit fine

All wiring is plug and play at the back and labelled example green to green purple to purple and so on so it's self explanatory

Hi, Nothing unless you run say a 12v - 5v usb regulator and then connect that up which would give 2 charging points but that's why its best to choose the head unit for the vehicle or application. I wouldn't pick an ax1000 personally for this vehicle or any for that matter unless the budget really didn't allow for anything else but yeah these usb points would be connected to nothing unless you do further add ons :)

Unfortunately not at the current time. I think aerpro are working on it but I'm not sure

@@D2iAuto i see. I hope they make something for territory tx. My car is running like an undead zombie. Never broke down since i bought it. Now at 290k km. Really want to upgrade that one with one of those head units.

Thanks! Here's a link to the Ford parts on my website :) d2iauto.com.au/56-falcon-bf

@@D2iAuto Sorry to be a pain but, I can see the bare facia, do you have a link for the android screen as well?

@@leonclince5462 it's not an android screen that's a double din head unit a Sony ax1000 I have Clarion fx450 in stock that works but that's all I have in stock

Hey man. Im from New Zealand, do you ship to us over here?

@@leonclince5462 not typically bit I could check pricing and see but it's a pretty big box but yeah I can check for you

Thanks! It was a sony xav ax3200 from memory I'm pretty sure I mention it in the video but yeah I think that's what it was

Thanks! I'm not sure what you mean by this. The carplay is just connected via USB to the front USB panel (has a USB pass through to the front from the rear) so then plugged in and connected to carplay and set up Siri and you're good to go :)

@@D2iAuto i’ve seen many headunits with the usb port coming out of the rear. thinking about getting this ICC for my BF but didn’t know how u can use the rear usb port of the headunit. unless u connect up to the USB ports on the ICC?

@@aaronkerr2536 ahh got you, yes the facia kit has a passthrough so basically a USB on the front of the facia that you can use that has a USB out the back to go to the rear USB on the head unit other than that you can also install flush mounted USB plugs in a location.of.your.choice.and.run.the USB to there or have a cable running direct to your phone holder from the rear through the cars trim all personal preference on how and where you want to connect it :)

@@D2iAuto Awesome! thank you very much for ur help!!

Great video by the way…thank you!

@@Paytrade Hey, thanks! Ambient temperature I'm not overly sure on I think it may through the info mode but don't quote me I don't own one of these vehicles so only had the cars in to fit the unit so not entirely sure. As for clock that will be head unit dependant but most head units will display time or at least have the option to

Key 1, Key 2 and gnd are used for OEM steering wheel controls for manual steering wheel setup otherwise if it has the 3.5mm jack with your part 2 harness then simply plug that in and forget about the key1,2 and gnd ( keep in mind you'll need to cut the loop cables to set the swc module up to match your head unit which is given in the manual and tells what colour to cut for what brand)

Speed connect won't be used on that model as it doesn't have speed pulse so tape it up and leave it disconnected

The FG kit has been made through aerpro they're just finalising it and waiting on parts of think estimate was end of this year so soonish will be out :)

@@D2iAuto Sweet! Did that Sony system you installed have navigation on it?

@@maxrockatanksyOG carplay and Android auto so navigation through that but I'd recommend Kenwood over Sony 5020s is good but 8020s is better but 5020s would be better suited being the half depth size

My local Autobarn had an FG one so I grabbed it a few weeks back. New head unit arrived this morning so next weekend it all gets installed

@@zachplier5704 interesting that they had one, they're not released yet or even available through the Australian distributor yet but that's awesome hopefully they're close then

@user-oq5rp2ki8c did you connect the video output from the aircon unit to the head unit reverse camera input?

@@D2iAuto affirmative - so the male yellow rca is plugged into camera input in the unit, purple reverse wire on head unit side of loom is connected to purple reverse wire on main harness side and then the female yellow rca is not connected to anything as I do not have a reverse camera installed yet in the car.

@user-oq5rp2ki8c do you get no video at all for aircon as well? If nothing at all potentially pal vs ntsc so may need to be swapped to the other video signal which may need another head unit to then access settings to change it as I cant remember if there is a pal vs ntsc dipswitch to change the settings on the module itself there may be

@@D2iAuto there is 4 switches on the back of the fascia in-between the plugs that the instruction manual which can be found online refers to them as dip switches.. I have had a play around woth switches 1 and 2 - 3 is supposed to reset the settings on the headunit and 4 is useless.. if you could have a squizz over it and let me know what you think it may be advising me to do for my unit to get it to pick up signal.. because yes as you said, both Trip and Menu buttons have the 'no video signal'.

Also woth aircon as well, the only work around for the meantime is to turn off reverse camera on my unit to it won't display that message.. but then by doing that, that doesn't really help because then the screen does not flick over to Trip/Menu/Climate Control.

If it's a sx or sy model then yes tx is like the level such as Gia etc so as long as it's sx or sy then the facia is the same. Cost on facia is about 600 from memory retail and a basic double din carplay and android auto head unit will put you back around 600 again. I do supplied and fitted discount packages for them as well though

Thanks for feedback where is your location

@@timjssuman3620 Ballarat Victoria

Its been made and prototyped and installed in a few cars recently so i think at the moment they are just waiting on the facias to be made and its all good to go so within the next couple of months possibly

@@D2iAuto by xmas hopefully

Yes you are. So the infodaptor (which is contained within the main aircon panel) has output to the reverse cam input of the new head unit but it also has a reverse camera input on the infodaptor itself so when in reverse and triggered it will override the infodaptor so only 1 reverse camera input is needed on head unit to do both :)

Just suxs rhe factory camera on the ghia models can't be retained

It's coming they were meant to be here by now but haven't arrived they're available for dealer backorder and were scheduled to arrive in December but it's been delayed with the chip shortage so not sure of an ETA as of yet

@@D2iAuto I contacted aerpro last month and they reckon mid year it will be released

@@philt3775 yeah at this it's not looking anytime super soon

Hmmmm I'm not sure on that one. As you can see in the video the whole plug could be pushed back and so far everyone I have done has allowed for this. Haven't been able to do it on the FG ones though they don't move much but haven't come across an issue on the ba bf as of yet for this. If you have a mechles shallow mount unit like a dmx5020s or clarion fx450 or grinding gx3800 and so on then you should be fine anyway

Nah my deck is a full size. I stuck my finger in behind the plug and there's some padding I'm guessing is on the firewall or whatever...

@@paulshearer9233 oh okay yeah it's not recommended to fit full size chassis units I think it will struggle without cutting and modification to air vents unfortunately

@@D2iAuto Yeah all good, I'll buy a shallow unit lol. Thanks mate

Yes it works with a reverse camera there is a patch lead that comes with it which has the reverse camera output (which goes to head unit reverse camera) and reverse camera input that goes to the reverse camera that way the head unit thinks it's in reverse and displays the aircon setup when aircon is pushed bit will override that with the reverse camera when in reverse

@@D2iAuto no need to connect the reverse trigger wire then? Maybe that’s what’s stopping mine working!!!

@@robtaylor893 nah the head unit reverse trigger needs to be triggered by the infodaptor so that it can turn it on when you touch aircon controls the actual reverse is then triggered through the infodaptor using canbus so no extra trigger needed then from memory the reverse camera is a setting to turn on

Got it… cheers

It doesn't have a factory reverse camera retention harness but i think they can be hard wired in should be able to be anyway. I haven't had to do one with a camera yet

You have to have the steering wheel control patch lead connected and also have it connected to head unit and can use adaptor before connecting it to the vehicle and power if its pioneer you'll have to turn steering wheel controls on in the settings with the source off. So there's a number of things it could be

Do I need to buy a separate lead or will the wiring harness that came with the facia do the job. I've checked the pioneer unit I don't have an option to enable or disable steering wheel controls, by the way thanks for the quick reply.

@anthony eldegel I can't remember if it comes with the universal patch lead but if it has a universal patch lead (has a 3.5mm jack and gnd key1 and key 2) then you don't need anything else. Disconnect the facia and head unit for at least 30 mins, make sure all the connections on head unit are connected first and the steering wheel control harness is connected etc. Then connect the facia to the vehicle last. Most pioneer units (not all) will require you to tell the steering wheel controls to be either an adaptor or oem control. Depending on the head unit you may need to turn the source off so the unit is on and source is off. Have handbrake on (assuming park brake wire is connected or otherwise the green wire grounded) then go to settings and set steering wheel controls to with adaptor and then they should work. If you go to settings and find steering wheel controls greyed out then make sure handbrake is on or as stated need to have the source off which is usually the arrow down at the top of pioneer units and select source off

Right so the steering wheel controls work I wired them up but I can't get the after market ac control to communicate with my pioneer unit they work, I can control the ac fans traction control etc but they don't show up on the unit.

@@anthonyeldegel7538 you need to wire the reverse trigger from the head unit to the output from the canbus module and then run the rca output from the canbus module to the input of the reverse camera

Yeah sure can :)

@@D2iAuto awesome mate, how much does that run for a kit, just a basic install, I have kickers so will have to mount take off to the left side of the boot, I need to retain the spare wheel and well

@@s4ss.m8 base kit non engineered and no autolevel supplied and fitted you'd be looking at 3k with the tank and compressor etc all mounted to the left of the boot

Nothing I can suggest other than check plugs and then test wiring so check for ground (black) Accessory (red) and Constant (yellow) If anyone of those have nothing then it won't work so check connections and fuses. That's all I can advise without having the vehicle next would be take it to your local audio shop for diagnosis

Thanks so much for replying back 😊

Hey it was faulty hvac that control AC/control

Have them available on my website d2iauto.com.au :)

hmmm i haven't really seen anything with any more cables can you shoot through some pics to contact@d2iauto.com.au and i can try help you out

@@D2iAuto hey mate, just thought i’d let you know, i’ve just fully put it together & it all works, the issue was i have a premium icc with premium sound in my BA which had multiple cables connected to the fob which i had to run under the bracket for the bcm before i inserted the bcm, and just made to tuck away all the extra wires which were unneeded 👍🏽

@@edantaggart9280 Ahh yes premium sound got you yeah too easy :) glad you got it all sorted anyway

This one didn't have a factory reverse camera but could easily hook up an aftermarket camera if wanted to. Factory cameras have to be hard wired in there's no retention harness for them currently

I think they're a 6.95" its just standard double din size so most double dins will range between 6.8-7" touchscreens

Yes i'm in Ballarat and i think it was a Ballarat car not sure though

this was a sony AX3000 id prefer the Kenwood DMX5020S or Clarion FX450 personally but the customer supplied this one

@@D2iAuto was just making sure whatever i order for it has a proven track record that everything works steering controls and all. the blend door controlls have locked up again, second control set i have put in now so thinking would be a good upgrade and fix the issue at the same time in my BA shaggin wagon

in all honesty i feel its priced pretty well. Factory integration isn't chap and when it has aircon controls involved that get removed it starts putting prices pretty high. A grand cherokee facia kit is over 1500 haha

It was the first vehicle I had installed it on, have done about 12 falcons though since I just filmed the first one which happened to be a territory :) But yes factory integration on systems with climate control built in is never cheap the canbus integration always means it will be expensive unfortunately so these options won't be for everyone.

No worries, sorry to waste 18 mins of your precious time 👌